Inline FabricationGraf & SonsMidSouth Shooters SupplyADvertise here
RotoMetals2Titan ReloadingStainLess Steel MediaLee Precision

Tab Content
  • mac1911's Avatar
    02-10-2018, 09:56 AM
    I am surprised there's no prevision on ballistic calculators for at least a rough change in poi vs a current zero with a change in load data. Example : I load a 30-06 load 168 grain at 2600fps my rifle is zeroed at 200 yards. Now I load a cast...
    21 replies | 539 view(s)
  • mac1911's Avatar
    02-09-2018, 09:26 PM
    Just buy the least expensive 1040-1100 fps ammo available closest to you.
    21 replies | 587 view(s)
  • mac1911's Avatar
    02-05-2018, 08:03 PM
    mac1911 replied to a thread Swiss K-31's in Military Rifles
    Whish they made a 5 rounder for cmp vintage match
    6 replies | 605 view(s)
  • mac1911's Avatar
    01-26-2018, 10:38 PM
    mac1911 replied to a thread Need help in AirGuns
    Im pretty good at finding parts and I can't find anything for these pistols other than that UK web site. I wold call umerex with the part number provided from that UK web site and see what they say. If the valve assembly and co2 inlet seal are cheap...
    6 replies | 304 view(s)
  • mac1911's Avatar
    01-26-2018, 10:34 PM
    I'm curious does bass pro or cabela even buy the products any more or do they basically lease out shelf space and take a percentage. Its just not seem right if they have the "buying power" they should offer better prices. Then again I don't want to...
    70 replies | 4159 view(s)
  • mac1911's Avatar
    01-24-2018, 09:04 PM
    mac1911 replied to a thread Need help in AirGuns
    from what I could tell the walther by umerex and crosman are the same ? Thisis the only place I found a parts diagram? https://www.gunspares.co.uk/products/24996/Walther-PPK/ for what these pistols run new I don't think theres a lot of...
    6 replies | 304 view(s)
  • mac1911's Avatar
    01-23-2018, 10:35 PM
    mac1911 replied to a thread Need help in AirGuns
    Do you have a model number, there is a parts list diagram look up on the web site. Depending on the model some are easier to rebuild than others. The cheaper ones are not worth it. ...
    6 replies | 304 view(s)
  • mac1911's Avatar
    01-23-2018, 10:21 PM
    I,have not had any decent accuracy with my cast loads through my M1s . one will cycle at 32 grains of H4895 but holds a loose group and its work keeping them in the black.
    11 replies | 546 view(s)
  • mac1911's Avatar
    01-22-2018, 08:02 PM
    mac1911 replied to a thread FX Cyclone Air Leak in AirGuns
    Can you hear it leak? Or does it leak slowly over time. If you don't want to put soapy water on it try some very light oil around all the fittings. Sometime something gets where it does not belong on the seals inside. Sometimes this works. Fill...
    5 replies | 249 view(s)
No More Results
About mac1911

Basic Information

Statistics


Total Posts
Total Posts
857
Posts Per Day
0.30
General Information
Last Activity
02-17-2018 04:37 PM
Join Date
04-25-2010
Referrals
0

1 Friend

  1. Sonnypie Sonnypie is offline

    Boolit Master

    Sonnypie
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check