Inline FabricationLee PrecisionRotoMetals2ADvertise here
WidenersTitan ReloadingMidSouth Shooters SupplyRepackbox

Tab Content
  • dragon813gt's Avatar
    Today, 12:08 PM
    It will run in Wine. But it may not just run out of the box and you will have to adjust settings. No, software as a service needs to go away all together. I want to pay once and then itís mine. If I donít want to upgrade thatís on me. W/...
    5 replies | 101 view(s)
  • dragon813gt's Avatar
    Today, 11:49 AM
    I switched to Ballistol a long time ago. It doesnít fall into the cheap category at around $100 a gallon. But itís non-toxic, safe on all materials, thicker and clings to parts and it doesnít gum up in cold weather. The last part doesnít apply to...
    23 replies | 491 view(s)
  • dverna's Avatar
    Yesterday, 10:59 AM
    Prayers....
    7 replies | 195 view(s)
  • dverna's Avatar
    Yesterday, 10:57 AM
    No way the barrel is .227+. It will not shoot jacketed bullets at all if it is. Use another micrometer or mic a jacketed bullet to verify the readings. If it really is a .227 barrel, contact CZ and they should replace it at no...
    20 replies | 616 view(s)
  • dverna's Avatar
    Yesterday, 10:50 AM
    I love my G22's. Even bought a Lonewolf 9mm conversion and 9mm mags so I can shoot two calibers with one gun. Mine is boringly reliable which is what I want in a SD gun. I shoot tighter groups with the Kimbers, but that level of precision is...
    47 replies | 793 view(s)
  • dverna's Avatar
    Yesterday, 12:20 AM
    For handguns it is a waste of time for the vast majority of guns, shooters, and applications. I used to do it until I started shooting a lot. If I still shot Bullseye, and had the skill I had 40 years ago, I would sort for the 50 yard stages and...
    73 replies | 1255 view(s)
  • dverna's Avatar
    05-24-2020, 04:48 PM
    Larry Gibson gave you the best insight IMHO. BTW, starting with a 5.56 in cast is not a good place to be, and you can look forward to an immense level of frustration. I would suggest NOT even trying unless you are more of an experimenter and...
    63 replies | 1493 view(s)
  • dverna's Avatar
    05-24-2020, 03:41 PM
    Agree. It is not as fast as a good 6 cavity mold but it allows you to cast for longer periods of time. I have nerve damage and cannot work with heavy molds for very long anymore. You want a consistent and very clean alloy so that is what I...
    11 replies | 185 view(s)
  • dverna's Avatar
    05-24-2020, 03:33 PM
    Lots of good choices above. My favorites are the Anschutz repeater my dad gave me over 55 years ago (still shoots less than 1.5 MOA with junk bulk ammo), a Winchester M52 sporter and the 10/22. If I was buying one now, it would be the CZ.
    28 replies | 578 view(s)
  • dverna's Avatar
    05-24-2020, 03:24 PM
    This morning I was reading a long thread on the .350 by Oldfeller on this site. He was working with an AR. Worth reading if you plan on loading the .350. There were (are?) a few issues with .350 cases that sounded concerning. It is nice to...
    6 replies | 148 view(s)
  • dragon813gt's Avatar
    05-24-2020, 03:20 PM
    Nothing is permanent, especially nations. If they really wanted out they would fight again. Time has seen nations and empires come and go. Nothing has changed that would prevent this from happening now.
    20 replies | 387 view(s)
  • dverna's Avatar
    05-24-2020, 11:17 AM
    This has been an interesting read.... A lot of work and experimentation that will help others on a similar quest. I would never make the journey as I have so little patience and talent yet I can appreciate those qualities in others.
    348 replies | 32029 view(s)
  • Ickisrulz's Avatar
    05-24-2020, 02:57 AM
    If you buy the brass directly from Starline, they ship it for free. The prices for 44 Mag brass are $110/500 cases and $191/1000. So if you buy 1000 cases, it's a little more than 19 cents per case (for new stuff).
    6 replies | 349 view(s)
  • dragon813gt's Avatar
    05-22-2020, 07:49 PM
    Maybe I am running the newest version then. I was part of the initial run and there were a few firmware updates early on. If it ainít broke donít fix it, which the firmware apparently is.
    36 replies | 873 view(s)
  • dragon813gt's Avatar
    05-22-2020, 07:42 PM
    For me time is the more valuable than anything else. Second to that is results on target. So I donít bother w/ wet tumbling 99% of the time. It takes to long due to the many steps required. And there is no positive result on target. If the...
    42 replies | 620 view(s)
  • dragon813gt's Avatar
    05-22-2020, 10:46 AM
    There have been multiple firmware updates over time. Might want to see what yours shipped with. That being said Iím not running the most recent version. Havenít had any issues and donít want any that inevitably pop up when updating firmware.
    36 replies | 873 view(s)
More Activity
About Ickisrulz

Basic Information

About Ickisrulz
Biography:
Retired from USAF, My wife is retired too
Location:
Shawnee, OK
Interests:
Sulcatas, ATVs, Woodworking, Biblical Studies

Statistics


Total Posts
Total Posts
2,554
Posts Per Day
0.69
General Information
Last Activity
Today 10:45 AM
Join Date
04-13-2010
Referrals
0

6 Friends

  1. Bob Krack Bob Krack is offline

    Boolit Master at Heavens Range

    Bob Krack
  2. Char-Gar Char-Gar is offline

    Boolit Grand Master

    Char-Gar
  3. dragon813gt dragon813gt is offline

    Boolit Grand Master

    dragon813gt
  4. dverna dverna is offline

    Boolit Master

    dverna
  5. jmort jmort is offline

    Banned

    jmort
  6. rl69 rl69 is offline

    Boolit Master

    rl69
Showing Friends 1 to 6 of 6
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check