Titan ReloadingADvertise hereGraf & SonsInline Fabrication
RotoMetals2MidSouth Shooters SupplyLee PrecisionStainLess Steel Media

  • mold maker's Avatar
    Today, 05:20 AM
    Do you have faith? Eventually all things will end. At that time all the wealth, food, and planning in the world wont prevent the inevitable. Infinity is just a dream of short sited people. Every morning I awake on the green side (while it still...
    96 replies | 2336 view(s)
  • mold maker's Avatar
    Yesterday, 03:29 PM
    mold maker replied to a thread Today's kids in Our Town
    I only had occasion to spank our Daughter twice and in her words, the idea that she had broken the trust between us was lots worse than the licks. My Son, on the other hand, required regular applications with the rod of wisdom. It seemed as if no...
    42 replies | 826 view(s)
  • mold maker's Avatar
    Yesterday, 02:32 PM
    If your knowledge of collector coins is lacking, stay away. Common silver rounds and bars are rarely faked, and the value is tied to spot price. It still pays to stick with recognized mints. Everyone brings up the SHTF and while it isn't...
    96 replies | 2336 view(s)
  • mold maker's Avatar
    07-17-2018, 11:12 AM
    SAFE is just a feeling like the pride you get for the money you spent. It has very little to do with keeping determined thieves from your valuables. The cheapest locked box will keep curious little fingers away. Good insurance is money better...
    65 replies | 2777 view(s)
  • mold maker's Avatar
    07-17-2018, 10:36 AM
    The idea that that amount of energy can flow through a tiny copper wire at that speed is mind-boggling, but it's a fact we can't deny. While I understand the energy isn't contained within the wire, it follows its path like a train and its tracks.
    63 replies | 1269 view(s)
  • mold maker's Avatar
    07-16-2018, 04:42 PM
    Like a dime store lock on the outside door. I'll keep toddlers out.
    65 replies | 2777 view(s)
  • mold maker's Avatar
    07-16-2018, 04:07 PM
    And this is the best Gov to its citizens in the world try another country. If you're concerned where else are they building walls to keep aliens out?.
    42 replies | 1162 view(s)
  • mold maker's Avatar
    07-16-2018, 09:01 AM
    Tip the mixer to the point that lead ALMOST exits with the water. The mixer action will release most of the clay and the outflow of water will carry it away. I used this method on several tons of range scrap in dense NC red clay. The resulting...
    63 replies | 2290 view(s)
  • mold maker's Avatar
    07-16-2018, 07:50 AM
    mold maker replied to a thread Sunday Supper! in Our Town
    Are there any leftovers, and what's your address. LOL
    8 replies | 193 view(s)
  • mold maker's Avatar
    07-15-2018, 06:55 PM
    mold maker replied to a thread Coffee in Our Town
    I've started my day with coffee for over 73 years that I can remember. The only exception being three mornings before surgeries, but I made up for it before dinner. It's not a matter of want or desire, it's a necessity for everyone within...
    56 replies | 1084 view(s)
  • mold maker's Avatar
    07-10-2018, 10:16 AM
    Man, I'd hate to have to remove a stuck boolit from 100' barrel. It would extend onto the neighbors' yard.
    29 replies | 746 view(s)
  • mold maker's Avatar
    07-10-2018, 09:58 AM
    As a boy, we used to burn car bodies to melt the lead off for race cars. The ground in that area was like pavement. There is a Wally World there now.
    12 replies | 643 view(s)
  • mold maker's Avatar
    07-10-2018, 09:46 AM
    The last of the Mom and Pop diners, as well as the last cafeteria in this county has closed. It's now fast food, chain stake place, or nothing. Just the memories make me hungry.
    51 replies | 1844 view(s)
  • mold maker's Avatar
    07-10-2018, 09:30 AM
    Coins usually cost a premium over spot related to the grade and number struck. There is also always the unknown factor of how many have been melted. Silver rounds and bars of recognized source cost only a stated value over spot. The...
    96 replies | 2336 view(s)
  • mold maker's Avatar
    07-10-2018, 08:32 AM
    mold maker replied to a thread Phillippine Navy ???? in Our Town
    Is there a political reason the reg navy isn't trained for combat with riles.
    10 replies | 457 view(s)
  • mold maker's Avatar
    07-09-2018, 09:32 AM
    mold maker replied to a thread Case Lub in Reloading Equipment
    All cases are de-primed and SS/citric cleaned. If required the pockets are swaged/reamed and flash holes cleared and beveled. Lanolin and alcohol lubed before sizing means no damage to dies. Trimming and chamfering leaves brass debris so cob...
    46 replies | 782 view(s)
More Activity
About Black Powder Bill

Basic Information

About Black Powder Bill
Biography:
FFL Retired as an officer & director in all my previous associations. Served my last term Labor Day 2013 as President of the NYSMLA.
Location:
Madison County Ga.
Interests:
shooting,reloading
Occupation:
Licensed stationary engr./hvac

Signature


Your're already a criminal, you just haven't been arrested yet!
BPB Wayne Weekly News 1999
What I write on this forum or any forum is my opinion unless otherwise stated.

Contact


This Page
http://castboolits.gunloads.com/member.php?13380-Black-Powder-Bill&s=4672fe53e2ed9e96e40a8065c389a9dd
Instant Messaging

Send an Instant Message to Black Powder Bill Using...

Statistics


Total Posts
Total Posts
264
Posts Per Day
0.09
Albums
Total Albums
3
Total Photos
11
General Information
Last Activity
Today 10:57 AM
Join Date
03-17-2010
Referrals
0
Home Page
http://www.blackpowderbill.com

1 Friend

  1. mold maker mold maker is offline

    Boolit Master

    mold maker
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check