RotoMetals2Graf & SonsMidSouth Shooters SupplyInline Fabrication
StainLess Steel MediaWisconsin TriggerLee PrecisionTitan Reloading

Tab Content
  • ulav8r's Avatar
    03-23-2017, 10:31 PM
    Never turn down any dies offered to you for free. :D:D
    6 replies | 506 view(s)
  • ulav8r's Avatar
    03-22-2017, 11:15 AM
    Lather is nothing but soap bubbles. The tailstock spindle on your machine does not need tanged drill bits but can use them. I think the Atlas/Craftsman uses a set screw point in a slot on the spindle to resist rotation. Using a dog on the shank...
    12 replies | 302 view(s)
  • ulav8r's Avatar
    03-20-2017, 07:25 PM
    ulav8r replied to a thread Winchester 1892 problem in Leverguns
    Primers backing out is an indication of excessive head space, but not necessarily dangerously excessive. Yes, rimmed cartridges will not alleviate excess headspace. At around 30K psi, excessive headspace can be a problem; mainly with brass life...
    22 replies | 535 view(s)
  • ulav8r's Avatar
    03-20-2017, 12:20 AM
    Had one stuck .308W case about 40 years ago. Had seen pictures of RCBS stuck case remover, so I used a 1/4-20 tap, a socket head screw, a 1/4 inch washer and a 9/16 socket to remove it. Easy peasy. I think I might have been using RCBS lube on a...
    21 replies | 390 view(s)
  • ulav8r's Avatar
    03-17-2017, 09:17 PM
    It's good when newbies buy good equipment. That's how I got a Reloader Special press, Uniflow Measure, 505 0r 510 scale, 3 sets of dies and a Lee hand primer for $50 about 4 years ago.
    79 replies | 2234 view(s)
  • ulav8r's Avatar
    03-15-2017, 09:39 PM
    At the NRA convention in 1976, I sat at the table with the gentleman who started and owned Saeco. He told us that he went to a stock manufacturer(don't remember which one) and bought their scraps of figured walnut to make handles for his molds and...
    36 replies | 1127 view(s)
  • ulav8r's Avatar
    03-14-2017, 02:22 PM
    Still doesn't explain what it is or how it works to do whatever it does.
    19 replies | 531 view(s)
  • ulav8r's Avatar
    03-13-2017, 11:08 PM
    Post 5 explains it. Some of the loads were not pressure tested and others were.
    8 replies | 262 view(s)
  • ulav8r's Avatar
    03-12-2017, 07:51 PM
    The different manuals were prepared by different people at different times using different lots of powder and different guns. Why should we expect them to agree exactly. Always start with minimum loads and work your way up till you are satisfied,...
    8 replies | 262 view(s)
  • ulav8r's Avatar
    03-12-2017, 05:29 PM
    When I started reloading in 1967, I used a Lee Loader. I found a piece of 5/16 brass rod and cut a piece about 5 inches long. Then put it in a drill and tapered the end a little with a file. I could then slide on a .308 case and polish it up with...
    29 replies | 700 view(s)
  • ulav8r's Avatar
    03-09-2017, 09:28 PM
    Then you are a lot more man than me. I would have to use a hoist or fork lift to pick up one.
    60 replies | 1990 view(s)
  • ulav8r's Avatar
    03-07-2017, 03:26 AM
    Owned a SMLE for a short while, while in school. Had it rebarreled to 30-40 with a 1903 barrel, so headspace was not a problem. Sold it as soon as I got the stock refinished. Did not take the bolt head off, did not know about the different sizes...
    42 replies | 1419 view(s)
  • ulav8r's Avatar
    03-03-2017, 03:23 PM
    The Neptune and other washers that use 3 phase motors have a VFD built in that take 120V single phase and electronically converts it to 3 phase. The VFD controls the motor speed by varying the frequency of the 3 phase power created. I worked in...
    73 replies | 1692 view(s)
  • ulav8r's Avatar
    03-02-2017, 01:31 PM
    Probably not, but I have data to back that up. When you consider how fast they run the automatic machines, it is a wonder they can get powder in the cases, much less hold a tight tolerance on the amount.
    76 replies | 1712 view(s)
  • ulav8r's Avatar
    03-01-2017, 05:14 PM
    Maytag Neptune was one of the first in the US.
    19 replies | 696 view(s)
  • ulav8r's Avatar
    03-01-2017, 05:13 PM
    Many newer washing machines use a high speed 3 phase motor. The high speed is used to spin dry the clothes so they do not have to spend as much time in the dryer. The three phase is so the speed can be varied electronically. Maytag Neptune was...
    73 replies | 1692 view(s)
  • ulav8r's Avatar
    03-01-2017, 05:05 PM
    Ain't shootin no deer at 60 yards with a .380. For precision rifle loads I'll use one of my scales.
    76 replies | 1712 view(s)
  • ulav8r's Avatar
    03-01-2017, 04:35 PM
    ulav8r replied to a thread Badly Burned!!! in Classics & Stickies
    My worst burn was sunburn on the insides of my ankles after a 3 day canoeing trip. Could not work for a week because I could not wear my boots. Next worst was from slaking lime getting inside my 6 inch rubber boots. The lime fell out of a kiln...
    169 replies | 74628 view(s)
  • ulav8r's Avatar
    02-28-2017, 11:30 PM
    Many newer washing machines use a high speed 3 phase motor. The high speed is used to spin dry the clothes so they do not have to spend as much time in the dryer. The three phase is so the speed can be varied electronically.
    19 replies | 696 view(s)
  • ulav8r's Avatar
    02-28-2017, 02:26 PM
    10 scoops = 27.7 grains 10 more the same, 10 more the same, close enough.
    76 replies | 1712 view(s)
  • ulav8r's Avatar
    02-27-2017, 02:20 PM
    Added bold text.
    15 replies | 664 view(s)
  • ulav8r's Avatar
    02-27-2017, 01:38 PM
    My Lee dippers do not drift, do not require warm-up, and can be used during a power outage. I use 2.77 grains of Unique in a 380 with Sierra blems, don't remember which dipper. This is just barely a starting load(old Unique, not current) that...
    76 replies | 1712 view(s)
  • ulav8r's Avatar
    02-27-2017, 01:26 PM
    Zoom 1550 RPM 115 VAC FAN MOTORitem number: 10-2614PRICE: $6.99 620 In Stocklimited to stock on hand. We describe our products as follows: New - Excess inventory that is new and unused. Quantities are limited. New...
    33 replies | 1076 view(s)
No More Results
About ulav8r

Basic Information

About ulav8r
Location:
NC Arkansas
Interests:
fishing, hunting, shooting, gunsmithing
Occupation:
retired engineer

Statistics


Total Posts
Total Posts
149
Posts Per Day
0.06
General Information
Last Activity
Yesterday 07:22 PM
Join Date
03-05-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check