Titan ReloadingLee PrecisionInline FabricationMidSouth Shooters Supply
RotoMetals2Graf & SonsStainLess Steel MediaADvertise here

Tab Content
  • abunaitoo's Avatar
    07-14-2018, 10:24 PM
    Got it done. Glad I didn't spend anything to do it. Had all the parts I needed. Used a brass tube and soldered the extension to the stone. Very little wobble, so all was good. I slowed down the grinder with a cheap speed control for table...
    7 replies | 243 view(s)
  • abunaitoo's Avatar
    07-14-2018, 09:48 PM
    abunaitoo replied to a thread Coffee in Our Town
    Used to drink coffee. Can't now. GOUT. I would always drink it straight. That way I could taste what real good coffee taste like. Fufu coffee is OK, but you can make almost anything taste good with enough sugar and stuff. It's funny, but...
    54 replies | 904 view(s)
  • abunaitoo's Avatar
    07-14-2018, 09:41 PM
    abunaitoo replied to a thread Texas Drivers in Our Town
    It's like a plague. It started in kakafonicate, and is spreading across the country. We, in hawaii, are already infected. Kind of like the show Walking Dead. They walk around with no brains, no honor, no respect, only care about themselves. ....
    41 replies | 655 view(s)
  • dagger dog's Avatar
    07-13-2018, 09:43 AM
    I like to wring as much accuracy out of each firearm I own, that requires a bench, once I know the firearm is capable, then I like to use as many positions off the bench. Then the only thing I can blame on a missed shot is me.
    41 replies | 933 view(s)
  • abunaitoo's Avatar
    07-13-2018, 03:10 AM
    I'm wondering why this is not bigger news???? I would think it would be headlines all over the world. During the ordeal, it was not headline news on any of our local stations. Not even front page in the paper. I read yahoo news, and it wasn't...
    20 replies | 385 view(s)
  • abunaitoo's Avatar
    07-12-2018, 07:26 PM
    Not really a hole, but close. I'm trying to take the bell mouth out of a lathe chuck. I was looking for an easy way out. I'll try the suggestion from kenton. If not, I'll make a holder.
    7 replies | 243 view(s)
  • abunaitoo's Avatar
    07-11-2018, 11:33 PM
    All I can find here are grinding stones with short shanks. Shank is 1/4" di and 1 1/2" long. I need it longer to reach inside a hole. I was going to epoxy an longer rod it into a tube to make it longer. Problem with this is it will not fit into...
    7 replies | 243 view(s)
  • abunaitoo's Avatar
    07-10-2018, 03:09 PM
    abunaitoo replied to a thread Phillippine Navy ???? in Our Town
    Once in a while, if I see someone having a really hard time, I may offer to help. 99% of the time they are glad for the help. 99% of the time, they just got the rifle and don't really know anything about it. Had one poor guy who went through 9+...
    10 replies | 449 view(s)
  • abunaitoo's Avatar
    07-10-2018, 05:06 AM
    So I have a bunch of 8mm Label on Hotckiss strippers. To hot to shoot through the 1886 Label rifle. I pulled a couple of strips and tried to fire the primers. Not one went off. Good hard hits. Deep dent. Saved the powder, hoping I might be...
    3 replies | 201 view(s)
  • abunaitoo's Avatar
    07-10-2018, 04:12 AM
    I stopped using Imperial case lube long ago. Kiwi Mink oil was the same thing. Worked the same. Was less half the cost for twice the amount. Something happened, and Kiwi has to stop making it. On suggestions from them, I started using their...
    19 replies | 388 view(s)
  • abunaitoo's Avatar
    07-10-2018, 03:24 AM
    While at the range this Sunday, noticed a commotion going on a few tabled down from me. One of our Filipino range safety officers was scolding a bunch of shooters. All in Filipino. Found out later, they were sailors from Philippine Navy, here for...
    10 replies | 449 view(s)
  • abunaitoo's Avatar
    07-05-2018, 05:25 PM
    abunaitoo replied to a thread Master & apprentice in Our Town
    I thought it was rubbish.
    20 replies | 608 view(s)
  • abunaitoo's Avatar
    07-05-2018, 03:34 AM
    Throw some fresh orange peels, or any other fruit skin like it, in when vibrating. Keeps down on the dust, and the acid helps clean.
    23 replies | 542 view(s)
  • abunaitoo's Avatar
    07-05-2018, 03:10 AM
    abunaitoo replied to a thread Steve's pages website in Our Town
    It's working for me. I just clicked on the "X" in the log in box.
    7 replies | 350 view(s)
  • abunaitoo's Avatar
    07-03-2018, 03:12 PM
    The one I saw, looked like it has been taken apart. The measure arm is missing half of it. What looks to be the IR is removed. Pan is missing. If whoever took the IR out, also took parts out of the housing. It might now be worth anything. It...
    12 replies | 336 view(s)
  • abunaitoo's Avatar
    07-02-2018, 09:43 PM
    I wonder if it would work in a vibrator???? Seems like it would clean tarnished dirty brass really fast.
    16 replies | 465 view(s)
  • abunaitoo's Avatar
    07-02-2018, 06:19 PM
    Probably right. Poi is good. Also Ulu (bread Fruit)
    5 replies | 291 view(s)
  • abunaitoo's Avatar
    07-02-2018, 06:10 PM
    Has anyone tried red granite sand blast media for cleaning cases????
    16 replies | 465 view(s)
More Activity
About abunaitoo

Basic Information

About abunaitoo
Shooter/ Reloader for over 30 years.
Kaneohe, HI
Old firearms


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 05:35 AM
Join Date

1 Friend

  1. dagger dog dagger dog is offline

    Boolit Master

    dagger dog
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check