Titan ReloadingLee PrecisionInline FabricationRepackbox
MidSouth Shooters SupplyRotoMetals2ADvertise hereWideners

  • trapper9260's Avatar
    11-15-2019, 07:01 AM
    Years ago I had the Game Warden stop by while I was setting beaver traps .I seen him speed down the road and pull in fast where I was park. He got out and seen who I was and since he know me . He said I know I wasting my time . But I like to see...
    61 replies | 893 view(s)
  • trapper9260's Avatar
    11-13-2019, 06:27 PM
    I had my 357 lock up on me about 2 months ago and got it close after I remove the 2 plates and then was not able to fire it so I took it to my gunsmith and he had idea of a peace break on it and ask me about do I have a had time to load it I said no...
    24 replies | 8713 view(s)
  • trapper9260's Avatar
    11-11-2019, 05:06 PM
    trapper9260 replied to a thread Veterans Day tomorrow in Our Town
    You sum it up good Larry . For me I sign up delay entry for the navy to finish high school and then one week out of high school I went in from 79 to 83 active duty in the navy and then 83 to 84 in active reserves . then 88 to 90 active...
    34 replies | 575 view(s)
  • trapper9260's Avatar
    11-11-2019, 08:33 AM
    I only cut the brass is when the mouth start to split. Otherwise I did buy some 44spl brass for the reason of instead of down load my mag to spl ,That way I will not have to think of what one is low charge in the mags .
    33 replies | 957 view(s)
  • trapper9260's Avatar
    11-10-2019, 08:24 PM
    I do the same also and do it with 357mag also to 38spl. also will do it with 327mag if need to .
    33 replies | 957 view(s)
  • trapper9260's Avatar
    11-09-2019, 03:27 PM
    For me I would say the 44 mag for all that you can do with it also shoot spl in it . also the 357 mag that you can do the same and shoot spl. if you want to get small and med I would say the 327mag for all that you can shoot in it . I have a rifle...
    63 replies | 2001 view(s)
  • trapper9260's Avatar
    11-05-2019, 08:42 PM
    trapper9260 replied to a thread NAFA done in Lets talk trapping!
    Here is more on this https://mailchi.mp/1826a83db276/letter-from-nafas-president-1411865?e=143b650a1f November 4, 2019 Dear NAFA Customer, On October 31, 2019, North American Fur Auctions (NAFA) sought and was granted creditor...
    2 replies | 153 view(s)
  • trapper9260's Avatar
    11-02-2019, 05:42 AM
    For those that ship furs to NAFA they are done . They are out of the wild fur . Just ranch. Here is a write up on it that I found this morning. What's on T-Man: This is a summary of Tuesday’s conference call, with the receiving agents...
    2 replies | 153 view(s)
  • trapper9260's Avatar
    10-31-2019, 08:02 AM
    trapper9260 replied to a thread New cartridges. in Cast Boolits
    I went with the 327 mag because of all the rounds you can shoot in that same gun for what I was looking for and work for me .
    68 replies | 2104 view(s)
  • trapper9260's Avatar
    10-31-2019, 07:41 AM
    trapper9260 replied to a thread Cracked brass in Cast Boolits
    I have had some factory rounds that had cracked after I fire them. Other then that for what was stated for how it happeneds.
    44 replies | 1380 view(s)
  • trapper9260's Avatar
    10-30-2019, 07:07 PM
    I have some that I size to ,356 and some others will take .358 Need to slug the gun and go from there .
    25 replies | 712 view(s)
  • trapper9260's Avatar
    10-29-2019, 06:09 PM
    As for how I clean my mold and works for me, is I use the tooth brush with rubbing alcohol and let air dry and then .Preheat your mold on a hot plate then run your alloy hot . When the boolits is frosted then you lower the heat on the pot some.I to...
    11 replies | 413 view(s)
  • trapper9260's Avatar
    10-29-2019, 04:11 PM
    trapper9260 replied to a thread Cabela's club dollars in Our Town
    I drop them and close the card from them. They are too high price .
    13 replies | 595 view(s)
  • trapper9260's Avatar
    10-28-2019, 03:08 PM
    trapper9260 replied to a thread Bullet Hardness ? in Cast Boolits
    I would mix them also .
    17 replies | 490 view(s)
  • trapper9260's Avatar
    10-28-2019, 10:52 AM
    I got a Ruger SP101 327 Mag with a 4" barrel.
    1857 replies | 220002 view(s)
  • trapper9260's Avatar
    10-27-2019, 07:39 PM
    Anything cotton that is thick if not I add layers.When it get to burn I just change it . That is what works for me .I use old socks and stack them.
    30 replies | 832 view(s)
More Activity
About trapper9260

Basic Information

About trapper9260
Location:
Iowa

Signature


Life Member of NRA,NTA,DAV ,ITA. Also member of FTA,CBA

Statistics


Total Posts
Total Posts
2,442
Posts Per Day
0.69
General Information
Last Activity
Yesterday 06:21 PM
Join Date
02-14-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check