Graf & SonsStainLess Steel MediaRepackboxTitan Reloading
RotoMetals2WidenersMidSouth Shooters SupplyInline Fabrication
Lee Precision
  • trapper9260's Avatar
    Yesterday, 08:39 AM
    I remove them also on the press and had not one go off.I do like stated slow to take it out. But Dan Cash stated we all gonna die and the end of us all.
    27 replies | 337 view(s)
  • trapper9260's Avatar
    11-14-2018, 08:35 PM
    What are you doing with the furs? That is the main fur that have a market on it.I trap 2 today .
    4 replies | 213 view(s)
  • trapper9260's Avatar
    11-14-2018, 08:04 AM
    It was a rain day for opener and for the 2 days after and everything is slow not like it was the past years and took care of 2 beaver problems and work on a 3rd one that the landowner i met at one of the places I normal trap and got my otter that...
    12 replies | 481 view(s)
  • trapper9260's Avatar
    11-11-2018, 08:57 AM
    I use some and ones that show that dose work .I seen it first hand of a buck stop in its tracks when on the run .Was something to see and did get the buck and one other I use with it also works and got my doe with it watch the does walk right to the...
    24 replies | 436 view(s)
  • trapper9260's Avatar
    11-04-2018, 10:04 AM
    What I have done is use the weight that is close to the shot load and go with that data and work for me.Someone had sent me some slugs to try on my 10ga side by side and that is what they told me do and it work great.
    23 replies | 633 view(s)
  • trapper9260's Avatar
    11-03-2018, 07:44 AM
    Good start .Season open today for here in Iowa at 8am. i have a place across the road that the landowner have a beaver in it this year and some rats. It will be long days for me till it slows down for me later on in the season.
    12 replies | 481 view(s)
  • trapper9260's Avatar
    11-02-2018, 11:00 AM
    I use the fork rod made of maple.I do not eel the bark off, I can tell if it is surface water or in ledge. I had work for a well drilling outfit years ago as a helper on the drilling rig .the operator was usen the rods and was walking too fast and...
    45 replies | 2087 view(s)
  • trapper9260's Avatar
    11-02-2018, 09:25 AM
    I do up my own and use the trimmings when cut up the deer and do not add anything to it when ground up and cook it slow and it is just right for me. When I do beaver that is when get the cheapest beef from the store and add that to the beaver that...
    38 replies | 1271 view(s)
  • trapper9260's Avatar
    10-29-2018, 03:45 PM
    Thanks for explain this more.I have one that my dad got years ago and the problem got was the finish crimp part did not feed to well in a pump. So what I did is deprime and size in my Mec and have the hulls done all up that way then when I need to...
    22 replies | 687 view(s)
  • trapper9260's Avatar
    10-28-2018, 10:05 AM
    trapper9260 replied to a thread success in Hunting with CB's
    I still need to fill my permit with a crossbow also.No luck yet. I do not care what it is,doe or dose not matter.I did fill my permit for early muzzle loader . I got a doe.She was a good size one.Alot of fat on her also .
    19 replies | 977 view(s)
  • trapper9260's Avatar
    10-28-2018, 10:03 AM
    For my rifle What ever I use in my RH I can use it also in the Marlin. just size a little bigger.I use SWC and feed with out any problems. Just the WC is that I need to feed like a single shot.
    10 replies | 363 view(s)
  • trapper9260's Avatar
    10-25-2018, 11:54 AM
    You got to start somewhere. You are doing good. For the tree rat have you check around see if there is any taxidermist might like to buy any off of you or check around ? Also check check if there is a market on the skins or tails of them. Yes it...
    12 replies | 481 view(s)
  • trapper9260's Avatar
    10-25-2018, 11:51 AM
    Try not to smart the beaver up. Look for channel to set and use dive poles also.If you like to know anything else if I can help PM me.
    12 replies | 481 view(s)
  • trapper9260's Avatar
    10-25-2018, 11:46 AM
    Nice write up and all you done on this. With the photos it was nice to see how things came together for you. Thank you for posting.
    44 replies | 2130 view(s)
  • trapper9260's Avatar
    10-24-2018, 05:57 AM
    trapper9260 replied to a thread Range Scrap BHN in Cast Boolits
    I seen this also for all Larry wrote. It all depend on what is used .When I get all my range alloy done up I always test it to see what it is and go from there.Some times I just use it as is.
    13 replies | 523 view(s)
  • trapper9260's Avatar
    10-23-2018, 07:47 PM
    I learn from the Lyman #3 cast boolit handbook.I do have the 4th one and like was stated you can get reprints from Cornell.I had got the 1st and 2nd from them.
    25 replies | 1088 view(s)
No More Results
About trapper9260

Basic Information

About trapper9260


Life Member of NRA,NTA,DAV ,ITA. Also member of FTA,CBA


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 08:40 AM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check