RotoMetals2Titan ReloadingLee PrecisionADvertise here
MidSouth Shooters SupplyInline FabricationStainLess Steel MediaGraf & Sons

Donate Now Goal amount for this year: 6000 USD, Received: 3800 USD (63%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • TCFAN's Avatar
    Today, 05:51 PM
    TCFAN replied to a thread 327 fed. mag. in Cast Boolits
    The seller is monticha2014 Here is the same grips I bought. https://www.ebay.com/itm/New-wooden-grip-for-Ruger-sp101-checkered-hardwood-handmade-grips/162085052642
    16 replies | 273 view(s)
  • TCFAN's Avatar
    08-13-2018, 10:01 AM
    I had a RCBS that broke. I boxed it up and sent it back to them with a note asking if it was covered by their life time warranty. About 1 week later got a new one in the mail. Can't beat that anywhere.
    37 replies | 589 view(s)
  • TCFAN's Avatar
    08-12-2018, 08:13 PM
    TCFAN replied to a thread 327 fed. mag. in Cast Boolits
    The 32 H&R ammo was some old stuff.I size my bullets at .314.The sp101 is more accurate than I can hold. I am not disappointed at all in the gun.Maybe I need to order some 32 H&R starline cases and try some wadcutters again.My trouble may have been...
    16 replies | 273 view(s)
  • TCFAN's Avatar
    08-12-2018, 09:58 AM
    TCFAN replied to a thread 327 fed. mag. in Cast Boolits
    Trailboss is one powder that I have not tried in my 327. I have used it in the 44 mag. super blackhawk with 215 gr boolit and is is a nice load.
    16 replies | 273 view(s)
  • TCFAN's Avatar
    08-12-2018, 09:17 AM
    TCFAN replied to a thread 25/20 and 218 Bee brass in Leverguns
    I use the Redding form and trim die in 25-20 and 218 bee to make 218 bee from 32-20 brass. Winchester 32-20 brass is easier to form than starline 32-20 brass.The 218 comes out a bit short but they work especially for cast loads....
    8 replies | 216 view(s)
  • TCFAN's Avatar
    08-12-2018, 08:50 AM
    TCFAN replied to a thread 327 fed. mag. in Cast Boolits
    The 32 H&R case never was as accurate as the 327 case with any load I tried. I really wanted the shorter case to work for wad cutter boolits for target shooting but never found a load that would do better than the 327 case. Never had any 32 S&W...
    16 replies | 273 view(s)
  • TCFAN's Avatar
    08-11-2018, 07:20 PM
    TCFAN replied to a thread 327 fed. mag. in Cast Boolits
    I have the same gun. I put a Burris red dot sight on mine.I found out real fast that my SP101 does not like the H&R case. Mine only likes the 327 case.I don't want magnum loads in my gun either. Not what I bought it for.I found 3.7grs. of Bullseye...
    16 replies | 273 view(s)
  • TCFAN's Avatar
    08-11-2018, 06:55 PM
    I finally got to shoot the pistol target today. This is a very difficult target.I shot one hand standing at 25 yards with my S&W 686 using a red dot sight and a 358495 wad cutter with 3.2grs of Bullseye in 38 special wad cutter case.A hard target...
    22 replies | 1104 view(s)
  • TCFAN's Avatar
    08-08-2018, 11:32 PM
    PM sent. Will get something up for this primer feed in a day or two.Thanks much appreciated.
    4 replies | 146 view(s)
  • TCFAN's Avatar
    08-08-2018, 05:06 PM
    My gas check shield on my chronograph was no match for a 45 acp at 10 feet
    67 replies | 1446 view(s)
  • TCFAN's Avatar
    08-08-2018, 04:48 PM
    well if no one else wants this I will take it.
    4 replies | 146 view(s)
  • TCFAN's Avatar
    07-31-2018, 09:47 AM
    For one hand Bulls eye shooting I find that my S&W 686 handles and shoots as good or better than my old S&W 14-6. Using the Lyman 358495 WC boolit with 3.2grs. of Bullseye powder loaded in a 38 special wadcutter case my 686 will put 6 rounds almost...
    46 replies | 1232 view(s)
No More Results
About TCFAN

Basic Information

Date of Birth
March 14, 1944 (74)
About TCFAN
Location:
Missouri Ozarks
Interests:
Shooting and Casting Boolits
Occupation:
Retired

Statistics


Total Posts
Total Posts
1,010
Posts Per Day
0.22
General Information
Last Activity
Today 06:30 PM
Join Date
02-04-2006
Referrals
0

1 Friend

  1. blaser.306 blaser.306 is offline

    Boolit Master

    blaser.306
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check