RotoMetals2MidSouth Shooters SupplyInline FabricationADvertise here
RepackboxLee PrecisionWidenersTitan Reloading

Tab Content
  • M-Tecs's Avatar
    Yesterday, 02:17 AM
    Back in the day it was claimed to be the best and I believe that claim, however, synthetic oils of today are far superior .
    18 replies | 374 view(s)
  • M-Tecs's Avatar
    12-09-2019, 11:54 AM
    When I first started shooting NRA Highpower Service Rifle Competition with M1's and M-14's I only used GI ammo or loads with CCI #41 primers. After watching the military teams shoot 100,000's of Federal Gold Medal match I became much less...
    17 replies | 455 view(s)
  • kywoodwrkr's Avatar
    12-08-2019, 10:59 PM
    Is there a similar presentation for a M14SA? Have a LRB barreled action to put in completion status. Had this since '08 so time to finish it. Only problem then is finish the M1(from '05) first or M14SA. Don't handle dilemmas real well. Thanks.
    11 replies | 271 view(s)
  • kywoodwrkr's Avatar
    12-08-2019, 09:48 PM
    Text book for use in basic machine tooling vocation class room. Some times they get new ones which is hoping will be selected as course text book. I have one which is over ten years old and as many 'updates' ie new # more $. Still refer to it for...
    11 replies | 287 view(s)
  • M-Tecs's Avatar
    12-08-2019, 06:51 PM
    I've done maybe 200 or 250 trigger jobs on M1's or M-14's. Everyone one that has doubling issues was corrected by process laid out in post two. I have only shot a limited number of Federal primers in an M1. I have fired a large number of...
    17 replies | 455 view(s)
  • M-Tecs's Avatar
    12-08-2019, 03:13 PM The MI and m14 bolts and triggers are basically same. Page 7 below has some very good info. ...
    17 replies | 455 view(s)
  • M-Tecs's Avatar
    12-07-2019, 06:51 PM
    Doubling is common with both the M1 and M-14 triggers that have been stoned a little to much or heavily worn. The fix is simple and only requires a small piece of sand paper. The cause is your finger bump firing the trigger. ...
    17 replies | 455 view(s)
  • M-Tecs's Avatar
    12-06-2019, 10:44 PM
    Take a black magic marker and color the case than insert into the chamber and rotate the case. You will be able to see were the contact is. Once you do that you can figure out why.
    47 replies | 1532 view(s)
  • oldred's Avatar
    12-06-2019, 01:23 PM
    Heat treating doesn't work that way. Besides heat treating comes in two flavors, through hardening and case hardening with the old rifles being made of early grades of weaker steel (with BP rifles usually being even weaker) and being case hardened...
    26 replies | 906 view(s)
  • oldred's Avatar
    12-06-2019, 12:47 PM
    Now ya dun'it, got clean the coffee off my computer! :lol: Thanks for the morning chuckle!
    10 replies | 456 view(s)
  • M-Tecs's Avatar
    12-06-2019, 03:00 AM
    Springfield M-1903 Style T, Heavy Barrel target rifle, .30-’06. The Style T ’03 rifle is quite rare, only 100 were ever made by Springfield Armory in 1929-32.
    4 replies | 1145 view(s)
  • M-Tecs's Avatar
    12-06-2019, 02:55 AM
    I was commenting on this type of swager I forgot about these
    25 replies | 1303 view(s)
  • M-Tecs's Avatar
    12-05-2019, 10:46 PM
    I like both the heart and liver but I would not grind liver and add to hamburger. Hearts no issue but the taste and color of liver is not a good mix with hamburger in my opinion. Liver is reserved to liver and onions at my house.
    47 replies | 1287 view(s)
  • M-Tecs's Avatar
    12-05-2019, 10:41 PM
    I have never used the RCBS PP swager so I don't know if this is even possible to create issues with 30 cal cases. With the Dillon 600 Super Swager on 223 cases the inside support is small enough that if you over swage the pocket you can collapse...
    25 replies | 1303 view(s)
  • M-Tecs's Avatar
    12-05-2019, 06:14 PM
    Winchester offered various types of set triggers in addition to the standard.
    15 replies | 14182 view(s)
  • oldred's Avatar
    12-05-2019, 11:25 AM
    I don't know what's the big deal about those short chambers but it seems that most everything is geared toward them, reamers, dies, etc. When building my 38-55 I insisted on (and still do!) having the CORRECT long chamber but it seems that most of...
    10 replies | 456 view(s)
  • M-Tecs's Avatar
    12-05-2019, 01:18 AM
    Yep mine mostly collects dust for this reason.
    32 replies | 2528 view(s)
  • M-Tecs's Avatar
    12-05-2019, 12:51 AM
    Not very much bluing wear so not that many rounds. More detail here ...
    7 replies | 1081 view(s)
  • M-Tecs's Avatar
    12-05-2019, 12:48 AM
    I started casting in 1968 with Lyman 4 cavity for 45 Colt and 45/70. My most used molds are H&G 10, 8 or 6 cavity with a close second to my brass 4 cavity. The older Lyman's that I own cast on size or larger. The newer ones are on size or under. ...
    18 replies | 960 view(s)
More Activity


Total Posts
Total Posts
Posts Per Day
General Information
Join Date

4 Friends

  1. kywoodwrkr kywoodwrkr is offline

    Boolit Master

  2. M-Tecs M-Tecs is offline

    Boolit Grand Master

  3. taiden taiden is offline

    Boolit Buddy

  4. terryt terryt is offline

    Boolit Buddy

Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check