MidSouth Shooters SupplyTitan ReloadingStainLess Steel MediaInline Fabrication
Lee PrecisionADvertise hereRotoMetals2Graf & Sons

Tab Content
  • Duckiller's Avatar
    10-14-2017, 06:30 PM
    Given the same weight boolit ,both the Sectional density and the ballistic coefficient are greater in a 0.338 boolit vs a 0.357 boolit.
    16 replies | 284 view(s)
  • Duckiller's Avatar
    10-14-2017, 06:14 PM
    Duckiller replied to a thread Gun theives sentenced in Our Town
    I have a problem with someone being charged in federal and state courts. I know courts don't agree with me but I think it is double jeopardy. Let the two prosecutors decide who has the best case and try some in that court. If they don't...
    16 replies | 588 view(s)
  • Duckiller's Avatar
    10-11-2017, 01:22 PM
    Duckiller replied to a thread Need help. 45/70 in Cast Boolits
    When I got my Marlin 45/70 I got two lee molds,330 & 405. Both are fun to shoot over minimum charges of Trail Boss. For larger animals I use 5744. Black powder loads in trap doors killed lots of bison. Are you shooting something bigger than a...
    20 replies | 534 view(s)
  • Duckiller's Avatar
    10-10-2017, 12:27 AM
    Low speed load i used 11.5 (I think) gr of 700X under a 185=/- gr lyman boolit cast with wheel weights, air cooled. Probably my most accurate load in any gun I own. Started at 10.0 gr and increased at about0.5 gr until It really got good at...
    19 replies | 608 view(s)
  • Duckiller's Avatar
    10-03-2017, 04:03 PM
    Have had no trouble crimping 44Mag with RCBS dies. Cast and jacketed projectiles. For single and double action revolvers, Desert Eagle and a couple of rifles. Would suggest than you closely follow the instructions for setting crimp.
    14 replies | 453 view(s)
  • Duckiller's Avatar
    09-28-2017, 05:41 PM
    MI has lots of doe licenses but only in the southern part of the state. UP and ULP you have to draw a doe permit. Before you apply you have to decide if you are going to hunt on private property or public land. Have to apply before Aug 15. ...
    47 replies | 1524 view(s)
  • Duckiller's Avatar
    09-26-2017, 03:42 PM
    I have a smal supply of Berdan primers that I use to reload 7.5x55 Swiss brass. It is just too pretty to throw away. I use the hydraulic method to deprime fired primers. Set shell in a socket that fits the base. Fill with water slide a 30...
    19 replies | 725 view(s)
  • Duckiller's Avatar
    09-24-2017, 04:39 PM
    Duckiller replied to a thread Marlin 38-55 in Factory Rifles
    Wait a while it may get cheaper. It is a caliber that I want but not sure I can justify. Have a 338 Win Mag and a 348 Win to shoot big things.
    18 replies | 669 view(s)
  • Duckiller's Avatar
    09-24-2017, 04:17 PM
    Duckiller replied to a thread Ben Avery in Our Town
    Welcome back. We may have changed some in the last 3 years!
    6 replies | 458 view(s)
  • Duckiller's Avatar
    09-20-2017, 02:59 AM
    Load #2 son's Casull with small rifle magnum primers. Stout loads but not anything screaming hot.
    16 replies | 440 view(s)
No More Results
About Duckiller

Basic Information

Date of Birth
December 1, 1942 (74)
About Duckiller
So. Cal.
hunting shooting fishing
retired civil engineer


This Page
Instant Messaging

Send an Instant Message to Duckiller Using...


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
10-15-2017 07:52 PM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check