Lee PrecisionMidSouth Shooters SupplyADvertise hereInline Fabrication
RepackboxTitan ReloadingWidenersRotoMetals2

Donate Now Goal amount for this year: 6000 USD, Received: 5750 USD (96%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • redneck1's Avatar
    Today, 05:03 PM
    redneck1 replied to a thread A quick ammo box in Special Projects
    Thanks :) I did think about a box joint , and might do a couple if I don't have to put a bunch of time into making a sled and a jig . If I had a decent table saw I wouldn't be adverse to doing the work . But I plan on dumping the one I...
    5 replies | 94 view(s)
  • redneck1's Avatar
    Today, 03:38 PM
    Free time can be a dangerous thing .... I hate the cheap plastic ammo boxes . So I fired up my crappy table saw and whipped up an ammo box for the 32-20 I am not a wood worker I don't have a good table saw nor do have a dado blade set ....
    5 replies | 94 view(s)
  • redneck1's Avatar
    08-10-2019, 02:23 PM
    I've been planning a 12x16 shed myself for this fall . Local prices for pre built are about the same here as the op. After looking at those and pricing store bought materials I learned that holy cow material prices are a bit crazy . So...
    17 replies | 800 view(s)
  • redneck1's Avatar
    08-10-2019, 01:35 PM
    I did some math and basic research .... average lenght of gun season for deer is 13 days and average success rates hover around 50% So I'm going to apologize to you , I guess to see 1000 deer shot on drives you've got roughly 60-70 years...
    40 replies | 1543 view(s)
  • redneck1's Avatar
    08-10-2019, 09:25 AM
    Something else to think about , how old is your media ? It does wear out after awhile and doesn't clean as well . I change mine once or twice a year ...
    16 replies | 498 view(s)
  • redneck1's Avatar
    08-10-2019, 09:12 AM
    A little bit of mineral spirits and nu finish car wax in the media works just fine for me . One thing I have learned with the smaller cases is we tend to not put enough of them into the tumbler for them to work against each and they just sort...
    16 replies | 498 view(s)
  • redneck1's Avatar
    08-10-2019, 06:24 AM
    I don't hate to be the one to say , someone must . If you've had to use a follow up shot on wounded ,tracked game of any sort 50+ times I do think it's time for you to stop hunting . I'd guess one ,two ,even three times is forgivable . At that...
    40 replies | 1543 view(s)
  • redneck1's Avatar
    08-09-2019, 06:11 PM
    If you want to pay the small flat rate shipping I can send you 75 -100 Cases ... just send a pm
    11 replies | 697 view(s)
  • redneck1's Avatar
    08-03-2019, 04:13 AM
    We all know the usual species of wood everyone uses to smoke their dinner .. hickory , fruit woods , mesquite , .... etc etc etc So what are the less traditional woods you've used ? ... good or bad . last week I got down far enough into my...
    54 replies | 1116 view(s)
  • redneck1's Avatar
    07-30-2019, 08:29 PM
    Sold .. thank you sir :)
    2 replies | 234 view(s)
  • redneck1's Avatar
    07-30-2019, 07:47 PM
    Opened up a nos box of what was supposed to be 50 grain fmj bullets and found it had 500 each of 50 and 55 grain bullets in it . I have no desire to change my loads in either .223 or .22 hornet So save yourself a few bucks and take these off my...
    2 replies | 234 view(s)
  • redneck1's Avatar
    07-29-2019, 05:33 PM
    If your only planning on doing a few molds you don't need a super expensive self centering vise. I've dabbled in making a few molds and I use a grizzly vise , I think it was a bit over $100 and works just fine for me after making a set of soft...
    22 replies | 2009 view(s)
  • redneck1's Avatar
    07-25-2019, 05:24 PM
    I'm sorry , I didn't catch your question tdoor45-70. Yes it's for a 577-450 chamber .
    7 replies | 432 view(s)
  • redneck1's Avatar
    07-25-2019, 03:24 PM
    Chamber is exactly the same as a revolver cylinder . Sold , funds recieved
    7 replies | 432 view(s)
  • redneck1's Avatar
    07-24-2019, 09:50 PM
    I spent three hours making this for a guy at the club because he seen mine and insisted he just had to have one . He then cheap skated out when I told him I needed $50 for it . So if you want it ,... $50 , plus small flat rate shipping of...
    7 replies | 432 view(s)
No More Results
About redneck1

Basic Information

About redneck1
Location:
ohio
Interests:
fishin and shooting
Occupation:
heavy equipment

Statistics


Total Posts
Total Posts
190
Posts Per Day
0.05
General Information
Last Activity
Today 06:24 PM
Join Date
01-24-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check