Inline FabricationStainLess Steel MediaMidSouth Shooters SupplyLee Precision
RotoMetals2ADvertise hereGraf & SonsTitan Reloading

Tab Content
  • Dale53's Avatar
    05-24-2018, 06:45 PM
    LUCKYDAWG; That “plum bluing” is just the light. It came with a very nicely polished and blued finish but has some “Honorable loss of bluing” from normal wear and tear. This has been an excellent performer since I first got it. Dale53
    17 replies | 282 view(s)
  • Dale53's Avatar
    05-24-2018, 06:05 PM
    Which just goes to show that we are all assembled a bit differently. The trick is to find what works for YOU! Dale53
    17 replies | 282 view(s)
  • Dale53's Avatar
    05-24-2018, 04:02 PM
    ghh3rd; I have had a Ruger Super Blackhawk since the sixties. I have shot nothing but full loads (and near full loads) by the thousands. When I first got the revolver, I put a set of Pachmayr grips on the revolver. I have never been bothered by...
    17 replies | 282 view(s)
  • Rick N Bama's Avatar
    05-18-2018, 09:40 PM
    Rick N Bama replied to a thread Land line phone in Our Town
    As well as "Why Run Backwards You Varmint" :bigsmyl2:
    28 replies | 824 view(s)
  • Rick N Bama's Avatar
    05-18-2018, 10:55 AM
    Rick N Bama replied to a thread Land line phone in Our Town
    The standard for the 4 conductor wire is to use Red & Green for the dial tone. Voltage between the two conductors should be 48vdc when idle and 100+vac when ringing. At least that's the way it worked for the Bell/AT&T Companies. It's been 16...
    28 replies | 824 view(s)
  • Rick N Bama's Avatar
    05-18-2018, 10:36 AM
    Rick N Bama replied to a thread Land line phone in Our Town
    The standard for the 4 conductor wire is to use Red & Green for the dial tone. Voltage between the two conductors should be 48vdc when idle and 100+vac when ringing. At least that's the way it worked for the Bell/AT&T Companies. It's been 16...
    28 replies | 824 view(s)
  • Dale53's Avatar
    05-18-2018, 09:08 AM
    I have shot THOUSANDS of my home cast bullets through various modern Smith revolvers with EDM rifling with NO issues. None, whatsoever. That includes my rather exotic Model 520: This is a titanium cylinder with composite barrel. It is a SHOOTER!...
    9 replies | 373 view(s)
  • Dale53's Avatar
    05-12-2018, 10:52 PM
    I am a .32 fan. I bought a Ruger SP101 in .32 Magnum. As you know, the rear sight was windage only and I couldn’t get the sights zero’d but I really liked the piece. I took it to my pistolsmith and had a red dot sight installed. My pistolsmith...
    26 replies | 750 view(s)
  • Dale53's Avatar
    05-11-2018, 11:25 PM
    Dale53, How does the 44 at 950 FPS compare to the comparable 45 caliber at the same speed? As you know, I prefer the 45 ACP/AR. Kevin I don’t believe there would be any significant difference between the two calibers/loads as far as the...
    20 replies | 3917 view(s)
  • Rick N Bama's Avatar
    05-09-2018, 09:29 AM
    Rick N Bama replied to a thread Gravy- Best jar Gravy in Our Town
    And yet another vote from me on the Idahoan. We have Potatoes so rarely around here these days (gotta watch the carbs) that we can't justify buying them. To me they're just about as good as the real thing. Jar Gravy doesn't have a place in our...
    46 replies | 1343 view(s)
  • Dale53's Avatar
    05-07-2018, 11:10 AM
    CJR; Thanks for sharing your info. In addition to several deer harvested with the Keith bullet, I have taken a number of edible small game with the .44 Special. If you shoot them through the head or through the slats, it is instant stop with...
    20 replies | 3917 view(s)
  • Dale53's Avatar
    05-01-2018, 08:20 PM
    I shoot a LOT of .38ís in my .357 revolvers. Immediately after shooting, I run a nylon chamber brush through the chambers while the revolver is still warm. The crud ring is soft and comes out readily. I carry these brushes in several calibers in my...
    29 replies | 1375 view(s)
  • Dale53's Avatar
    05-01-2018, 08:48 AM
    I have been casting bullets for longer than most have been alive. I have, on more than one occasion in the past, had the same problem. 1 - remove the base from the pot. 2 - select a drill bit obviously smaller than you need 3 - run that drill...
    5 replies | 254 view(s)
No More Results
About steveb

Basic Information

About steveb
Location:
Southern Indiana

Signature


[SIGPIC]http://i104.photobucket.com/albums/m193/stevensavage/avatars/reloadnPalacescriptresized.jpg[/SIGPIC]

Statistics


Total Posts
Total Posts
415
Posts Per Day
0.09
General Information
Last Activity
06-22-2013 05:33 AM
Join Date
01-22-2006
Referrals
2
Home Page
http://reloadingandlevergunning.blogspot.com/

3 Friends

  1. Dale53 Dale53 is offline

    Boolit Master

    Dale53
  2. kenjuudo kenjuudo is offline

    Boolit Master

    kenjuudo
  3. Rick N Bama Rick N Bama is offline

    Boolit Master

    Rick N Bama
Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check