RepackboxWidenersLee PrecisionInline Fabrication
ADvertise hereRotoMetals2Titan Reloading

Tab Content
  • akajun's Avatar
    02-12-2020, 04:48 PM
    akajun replied to a thread rifle barrels in Our Town
    Hart is good as is Krieger and Shilen
    16 replies | 626 view(s)
  • akajun's Avatar
    02-11-2020, 10:19 AM
    They were still being made into the 90's and early 2000's until Ray Vin came out with his version made from nylon wich never seized up from corrosion and had a little water reservoir in the bottom. Now Highpower rifle is pretty much all scopes but...
    18 replies | 852 view(s)
  • akajun's Avatar
    02-10-2020, 11:43 AM
    Ruger does not sell stripped actions for any of their guns. Only option is to buy used and strip down, or buy a savage action, pre fit barrel, and a chassis system.
    2 replies | 1108 view(s)
  • akajun's Avatar
    02-10-2020, 11:41 AM
    soaking in vinegar or phosphoric acid will do it.
    12 replies | 1038 view(s)
  • akajun's Avatar
    02-08-2020, 09:19 AM
    The Fed fusion is grouping, just not that well but it shows the rifle has the potential to shoot well. I’d start checking things like barrel touching the stock, hows the receiver sitting in the bedding area, etc. Next I’d try different loads. Did...
    19 replies | 475 view(s)
  • akajun's Avatar
    02-07-2020, 09:25 PM
    Scope issue? Did you send it to them with your scope on it? Even a misaligned chamber will group, just big. When it throws them wild somethings not tight or the bullet is not stable. So check your mounts, action screws, scope, if that is good try...
    19 replies | 475 view(s)
  • akajun's Avatar
    02-07-2020, 06:46 PM
    Sounds like your willing to spend the money to build a nice rifle. If not your better off buying a factory gun as you’ll be money ahead. If you go Mauser find a nice used commercial Mauser action. Parker hale, interarms, cz, Santa Barbara, fn are...
    27 replies | 1289 view(s)
  • akajun's Avatar
    02-05-2020, 09:58 AM
    It’s stress relief , most barrels are made from pre hardened steel, fully machined, then stress relieved. Believe it or not barrel steels like 4130 and 416 machine better in a slightly hardened state than when annealed.
    12 replies | 1188 view(s)
  • akajun's Avatar
    01-28-2020, 11:39 PM
    Some of your better custom smiths “time” the bolts on rem 700 type actions to what they call cock on close, but it’s really nice. They are really timing the action to slightly pull the sear back when you close the bolt, trying to optimize firing pin...
    23 replies | 925 view(s)
  • akajun's Avatar
    01-26-2020, 11:00 AM
    I use my large ring head for my brownells action wrench for small ring Mauser. The flat on the bottom of the reciever pretty much takes all the torque. So if you have a large ring action wrench try that. If your worried about the loose fit shim it...
    16 replies | 472 view(s)
No More Results
About akajun

Basic Information

About akajun
Location:
South Louisiana
Interests:
Highpower, Hunting

Signature


NRA High Master XTC
DR# 2125

Statistics


Total Posts
Total Posts
488
Posts Per Day
0.13
General Information
Last Activity
Today 07:32 AM
Join Date
01-18-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check