ADvertise hereMidSouth Shooters SupplyTitan ReloadingInline Fabrication
RotoMetals2Graf & SonsStainLess Steel MediaLee Precision

Tab Content
  • lead chucker's Avatar
    02-17-2018, 03:57 PM
    im out of bullseye got lots of unique. I like to find the most accurate load but not at the expense of my rifle. I have a few ponds of W231 but i like to save that for my 9mm. Unique is so versatile i wish it metered better.
    14 replies | 392 view(s)
  • lead chucker's Avatar
    02-17-2018, 02:34 PM
    Thanks guys. I will drop back to 5 gr. That load seemed to shoot good enough to kill pop cans.
    14 replies | 392 view(s)
  • lead chucker's Avatar
    02-17-2018, 04:24 AM
    I see lyman has loads for up to 7.5 gr Unique for the 45 acp with 200 gr cast boolit. All my other books call for more in the 5-6 range. Any one here try 7 gr unique? I have tried 7 gr in my just right carbine. Very accurate but has some recoil to...
    14 replies | 392 view(s)
  • lead chucker's Avatar
    02-17-2018, 04:13 AM
    lead chucker replied to a thread kel tec 2000?? in Factory Rifles
    I have a. sub 2000 gen II in 9mm and love it. Lots of fun to shoot. For what it is it's really accurate. Shoots 125 gr cast boolits with no problem sized .358. I like it better than my Just Right Carbine in 45 acp which i like allot.
    48 replies | 2301 view(s)
  • lead chucker's Avatar
    02-16-2018, 03:56 AM
    Spent half the evening after work looking for my Lyman 450 sizer wrench and wouldn't you believe it was in the last place i looked.
    5701 replies | 468011 view(s)
  • lead chucker's Avatar
    02-15-2018, 02:18 AM
    I like my 650. I have replaced a few springs in it. Keep it cleaned and lubed and works great. Just got a 45 acp conversion kit for it. Been loading a lot of 9mm to feed my hungry Keltec sub 2000. Its sits proudly next to my Rock chucker.
    39 replies | 1133 view(s)
  • lead chucker's Avatar
    02-12-2018, 10:49 PM
    Thanks guys. I will give them a try.
    6 replies | 258 view(s)
  • lead chucker's Avatar
    02-12-2018, 03:40 AM
    Any one use large mag pistol primers in a 45 ACP? I have a couple thousand mag primers i would like to make use of. Ive been using unique with 230 gr cast boolit. I have some W231 and red dot.
    6 replies | 258 view(s)
  • lead chucker's Avatar
    02-11-2018, 04:53 PM
    Just punched another 100+ discs to double check and its flawless. A little dab of 2 cycle oil will do ya.
    12 replies | 475 view(s)
  • lead chucker's Avatar
    02-11-2018, 04:20 PM
    Well guys i cleaned up the check maker and put a little 2 cycle oil on the cutter and so far it seems to have made a night and day difference. I didn't think this tool was in need of lube. So far so good. 1616s16 you should revisit your check...
    12 replies | 475 view(s)
  • lead chucker's Avatar
    02-11-2018, 02:36 AM
    I recently got back into casting boolits for my 44 mag. I have pat's check maker and the Free check's The free checks works good but is hard on my hands. I like Pat's but it keeps jamming up when you try to pull the disk cutter back down in the die....
    12 replies | 475 view(s)
No More Results

Statistics


Total Posts
Total Posts
655
Posts Per Day
0.22
Albums
Total Albums
7
Total Photos
46
General Information
Last Activity
Today 02:57 AM
Join Date
01-16-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check