ADvertise hereTitan ReloadingInline FabricationRotoMetals2
Lee PrecisionStainLess Steel MediaGraf & SonsMidSouth Shooters Supply

Tab Content
  • Harter66's Avatar
    Today, 02:59 PM
    Several books I have on hand show IMR 4350 with 150 and 170 gr jacketed . It has worked for me with cast , start loads often out run max loads for jacketed .
    14 replies | 226 view(s)
  • Harter66's Avatar
    01-18-2018, 01:38 PM
    Just because a 148 WC fits , feeds , and shoots well doesn't necessarily make it a good idea . This is in a Win case and fed in a FEG HP9 and a P95 DA .
    25 replies | 3220 view(s)
  • Harter66's Avatar
    01-17-2018, 07:46 PM
    Numbers ...... A NOE 535 at 1100 MV retains 1000ftlb with a 9' hold over at 350 yd . At 1400 the Lyman 458193 at 417gr from my example is about the same . It takes 1450 MV with the 462-420 MP at 414 gr . I have a 453-350 RNFP Mountain Moulds if...
    32 replies | 1992 view(s)
  • Harter66's Avatar
    01-17-2018, 05:52 PM
    I didn't break any wrist bones which surprised the bone/joint doctor a lot . I did however chip the long tip off the ulna and crushed the wrist end of the radius . Don't get off the wrong side of your motorcycle in the bottom of a wash in the desert...
    12 replies | 314 view(s)
  • Harter66's Avatar
    01-17-2018, 05:25 PM
    This is my preferred too . I have made assorted hold overs for range with this and it is for me as easy to make an adjustment for a body or duplex change as anything else I've used . I do have a couple of the old Weaver K4s with the fine...
    33 replies | 748 view(s)
  • Harter66's Avatar
    01-16-2018, 02:01 PM
    I load 5.5 Unique for a pair of 1917s with the NOE version of the 454424 and 452-200 RNFP Lee . The RBH likes it too . Even a high point carbine likes them . I'm almost out of the 12# keg of 1968 then I'll have to start all over with 2 cans...
    18 replies | 615 view(s)
  • Harter66's Avatar
    01-16-2018, 12:07 PM
    Mark me down . If I'm casting for best bullets I have no issue with a good single but I do find them tedious if I need very many of a particular bullet like a 454424 for example no point running a Lyman single when 4 rifles and 3 pistols don't...
    18 replies | 807 view(s)
  • Harter66's Avatar
    01-16-2018, 11:34 AM
    I talked to a fabrication shop and got some 22" hrs steel cutouts . Nice 3/4 " circle . Then I stuck them in a worn 20" tire from a tire shop junk pile and bolted it through the sidewall just above the bead shoulder . I added a plywood facer and...
    32 replies | 1808 view(s)
  • Harter66's Avatar
    01-15-2018, 03:28 PM
    The 6.8 is the 25,30&32 Rem shortened . The head shares the 30-30,32 WS dimensions but is rimless . The 22 Nosler is the 6.8 case with a rebated rim reduced to the shared 223 rim diameter . There's a 35/38/9mm produced on the 6.8 case . It is...
    4 replies | 136 view(s)
  • Harter66's Avatar
    01-11-2018, 08:07 PM
    So my nickle This is the RD 311-165 from NOE . I don't think you're going to get a bigger meplat mine comes in just under your desired 170 @168 , 171 checked and lubed ,170 PB dry . I also have if your 1-10 will shoot it the 311-230 . At...
    27 replies | 931 view(s)
  • Harter66's Avatar
    01-10-2018, 04:46 PM
    This is why you can "make do" with 32 Win Spl dies but not really . The Rem sisters have an almost AI/Weatherby shoulder that's fatter . I don't remember the dimension at this point but it is also on the order of .03 shorter to fit my chamber . ...
    9 replies | 215 view(s)
  • Harter66's Avatar
    01-09-2018, 03:01 PM
    I have a 279-124 @ 2795-127 . 225-55 @ 225-62 459-543 @ 460-535 As far as under over goes they are very close to dead on . Of the 6 orders I've made only 1 has had any delay and that was only a few days just about opening of hunting season...
    26 replies | 913 view(s)
  • Harter66's Avatar
    01-05-2018, 12:06 PM
    This is the prefix Marlin Remington . This starts with Remington production in 2009 . Rem has since added a laser QDR or whatever it's called square tag in front of that . This is the suffix on a 2010 . Currently it appears that A is for...
    9 replies | 266 view(s)
  • Harter66's Avatar
    01-03-2018, 11:30 PM
    Mine is a 10 just an A.
    9 replies | 266 view(s)
  • Harter66's Avatar
    01-03-2018, 03:31 PM
    I ladle cast . I ran a 458193 single for 125 pours . I tossed about 10 straight away for cold defects and 10-15 more for being out of the weigh lot . At the end I had 97 bullets of 416.7-417.4 I'm never going to complain about a run like that . I...
    23 replies | 659 view(s)
  • Harter66's Avatar
    01-03-2018, 02:57 PM
    I looked for some time myself . I had an 839 ........it didn't start out like that I'm sure , but the barrel was .305.3165 . A fired case would press fit a .323 with a .318 nose and the front band sticking out with a 323-175 Lee . I ended up...
    9 replies | 325 view(s)
  • Harter66's Avatar
    01-03-2018, 02:35 PM
    Mine is 2010 Remlin . It'll take a .461 . The gross barrel slug is .451-.4505 X .457+ <.4578 . It isn't egg shaped but it's not uniform , balanced but not uniform . It's almost like the bore was tapered small then pushed back out with the...
    14 replies | 403 view(s)
  • Harter66's Avatar
    01-03-2018, 02:12 PM
    I'll take the cannalure tool . Pm to follow .
    12 replies | 962 view(s)
  • Harter66's Avatar
    12-31-2017, 03:27 PM
    The nose flat dia is barely over half the bullet dia ...... I can't imagine a long run of cutting .225 + sprues on a 6 hole Lee . I'll see if I can scrounge up a replacement plate and open it up some . That would tend to explain the tendency...
    6 replies | 228 view(s)
  • Harter66's Avatar
    12-31-2017, 02:20 PM
    This is I think probably a fairly old but little used mould . I had a recent go with a brand new brass mould .......yeah well high desert stuff just doesn't rust or patina for beans here . I recently had a brand new Lyman mould that was...
    6 replies | 228 view(s)
  • Harter66's Avatar
    12-30-2017, 09:00 PM
    I have run 4-5 runs with this new to me but pre-owned mould , it seems to be just plain fickle . I washed it in Dawn , carb cleaner and finally brake clean . It continues to act like it has a dirty place uniquely placed on the Minnie style...
    6 replies | 228 view(s)
  • Harter66's Avatar
    12-24-2017, 11:02 PM
    Ran 105 of these . 454613 . This is the 285 gr Minnie version . Lotta fun in a Trapdoor .
    5530 replies | 443613 view(s)
  • Harter66's Avatar
    12-24-2017, 09:58 PM
    Here's a better place to start . Can she wink with both eyes separately ? I'm a RHLE . I had a vision drop on the left side . Appearently at some point in my shotguning I started shooting both open . When I discovered the vision was when going...
    41 replies | 1332 view(s)
No More Results

Statistics


Total Posts
Total Posts
4,076
Posts Per Day
1.39
General Information
Last Activity
Today 02:59 PM
Join Date
01-11-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check