Titan ReloadingLee PrecisionADvertise hereRepackbox
MidSouth Shooters SupplyWidenersRotoMetals2Inline Fabrication

Tab Content
  • Lead pot's Avatar
    Yesterday, 09:06 PM
    WBH. Here is a true Buffalo rifle that has downed two. Can I get that much money for this Shiloh .44-77 ? :bigsmyl2:
    13 replies | 522 view(s)
  • Lead pot's Avatar
    01-15-2020, 12:30 PM
    NAH been doing it going on 65 years. :D:D
    7 replies | 1325 view(s)
  • Lead pot's Avatar
    01-13-2020, 02:22 PM
    Lead pot replied to a thread Walnut hill dies in Swaging
    A few years back I talked to Rick Kalynuik of KAL tool and die about getting into making dies to fit the Walnut Hill Swage press and he was interested. But he had some health problems since so I don't know if he ever went into that line. He makes a...
    23 replies | 1907 view(s)
  • Lead pot's Avatar
    01-11-2020, 11:49 PM
    I think you guys using the reloading press swage dies would use a RCBS Big Max A-4 press or even the C&H three station H press and use the center die holder for doing this type of work. The Big Max is one super press I got on for mostly forming...
    22 replies | 1145 view(s)
  • Lead pot's Avatar
    01-10-2020, 08:17 PM
    Most of those sewer pipe bores was caused more by the mercuric priming compound than the black powder. Alsoback in that time mercury as in common use for cleaning lead out of the bore.
    27 replies | 1631 view(s)
  • Lead pot's Avatar
    01-06-2020, 11:39 AM
    I have two .16 ROT .40's one .40-70 and a .40-65 and one 14 ROT .40-65 and the 14 is outperforming the 16's with the same bullets from 1.4" too 1.5" long.
    5 replies | 224 view(s)
  • Lead pot's Avatar
    12-30-2019, 11:51 PM
    Even if a bullet eccentric and you run it through a sizing die to make it concentric it will still be out of balance. Shoot the eccentric bullet as it is. It will be concentric when it leaves the bore. :)
    9 replies | 577 view(s)
  • Lead pot's Avatar
    12-30-2019, 08:16 PM
    The lot of 1.5 Swiss I just finished was 04/05/2015 I still have a few cans of 3F Swiss that has been shooting well with a lot# 26/02/2018 And this is the most recent lot I have used and this 3F I did not have to make any adjustments over the last 3F
    40 replies | 1772 view(s)
  • Lead pot's Avatar
    12-29-2019, 11:08 PM
    Your better off getting a proper sized mould. You can't compress lead, all you can do is make it flow in a couple directions pushing it through a die.
    9 replies | 577 view(s)
  • Lead pot's Avatar
    12-29-2019, 10:40 PM
    There a lot of die hard Swiss users and it is/was/? a good powder. I use it but with the last case I shot up a couple weeks ago I have to see some good reports in the future before I buy another case. I have worked some very good loads using the OE...
    40 replies | 1772 view(s)
  • Lead pot's Avatar
    12-27-2019, 06:48 PM
    Nah, it don't bother me in the least with what you want to use. I tried it my self and I didn't like my cases getting edged with the green stuff that builds up. Down the bore is not a problem, salt or no salt because I clean my rifle when I get...
    57 replies | 3782 view(s)
  • Lead pot's Avatar
    12-23-2019, 03:03 PM
    The only experience I have with a hollow based bullet is the mini. I have shot a lot of my swaged cup and dish based bullets in the Sharps and all need a different a way to protect the fragile skirt. The dish or cup based bullets were designed to...
    19 replies | 887 view(s)
  • Lead pot's Avatar
    12-23-2019, 02:05 PM
    Cory. When you say hollow base, do you mean like in a mini ball? Some call a dish and cup base a hollow base. It makes a difference on what you use under them.
    19 replies | 887 view(s)
  • Lead pot's Avatar
    12-22-2019, 01:52 PM
    Lead pot replied to a thread Old E in Black Powder Paper Patching
    Chris, When I see occasional fliers and I don't think that it's so much the powder doing this if the rest are tight. Something else is going on. When I suspect it's the powder is when the groups open from golf ball to soft ball sized patterns...
    14 replies | 1225 view(s)
  • Lead pot's Avatar
    12-21-2019, 10:27 PM
    Your right the 57 was my .22 and the 62 was my .256. It's been a while. I might still have the .256 dies.
    27 replies | 1631 view(s)
  • Lead pot's Avatar
    12-20-2019, 10:12 PM
    Another great .25 caliber that was short lived was the .256 Win Mag chambered in the Mod. 57 Marlin's Levermatic. The 57 was a Box magazine short throw lever action that you could flip the lever without taking your hand off the grip. The little...
    27 replies | 1631 view(s)
No More Results
About Lead pot

Basic Information

About Lead pot
Location:
In a State that is #1 with people migrating out.

Statistics


Total Posts
Total Posts
2,984
Posts Per Day
0.58
General Information
Join Date
01-17-2006
Referrals
0

3 Friends

  1. RMulhern RMulhern is offline

    Boolit Master

    RMulhern
  2. steve klossing steve klossing is offline

    Boolit Mold

    steve klossing
  3. vikingson57 vikingson57 is offline

    Boolit Bub

    vikingson57
Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check