RotoMetals2Inline FabricationMidSouth Shooters SupplyTitan Reloading
WidenersLee PrecisionADvertise hereRepackbox

Tab Content
  • Lead pot's Avatar
    05-29-2020, 10:08 PM
    Lead pot replied to a thread Ladle weirdness in Casting Equipment
    I have never seen yellow dross on the ladle or top of the alloy but Gray dross is pretty common. You don't want that to get pored into the mould to cause an unbalanced bullet. Here is what you can do to keep the spigot of the ladle clean even if...
    13 replies | 343 view(s)
  • Lead pot's Avatar
    05-26-2020, 10:57 PM
    I'm, not sure what the wood is. It has a Oak type grain but I thought it looked nice in the Catalog :) In my eyes the black stocks will never replace good wood. I have only one rifle in my safes that has a composition stock and that is a 700 Rem...
    50 replies | 1705 view(s)
  • Lead pot's Avatar
    05-26-2020, 10:26 PM
    It's a Fajan. I got it from Herters around 1961 Here is the rest of the wood.
    50 replies | 1705 view(s)
  • Lead pot's Avatar
    05-26-2020, 09:57 PM
    Don't get me wrong, I liked the .220 but I did have the pressure problem with having to slap the bolt sometimes. I replaced it with the .22 Varminter I build a year before joining up in the service on a Czech VZ 24 98 Mauser action it has shot many...
    50 replies | 1705 view(s)
  • Lead pot's Avatar
    05-26-2020, 07:46 PM
    Oh your taking me back to the late 50's :) I had a Mod. 54 ? Winchester with in the .220 and I loved that rifle shot very well and busted the Fox too much for selling the hides but the ears had a $5. bounty on them. What I found with...
    50 replies | 1705 view(s)
  • Lead pot's Avatar
    05-26-2020, 04:14 PM
    There will always be disagreements and I been doing it for many years comments on this subject. I don't know what the load combinations were except they were reduced loads. One rifle was a Win 64 in a .30-30 caliber and the other was a Ruger all...
    50 replies | 1705 view(s)
  • Lead pot's Avatar
    05-26-2020, 12:55 PM
    A light load with the double base powder is just as dangerous as an over load. A light load has a good chance getting flashover from the hot primer igniting the whole load instead of a progressive burn load. I have seen two rifles that fragmented...
    50 replies | 1705 view(s)
  • Lead pot's Avatar
    05-26-2020, 07:56 AM
    A .220 Swift is even worse for pressure spikes necking down .270 brass I used before the .25-06 was a factory load. Makes for sticky bolts if you don't trim the necks.
    50 replies | 1705 view(s)
  • Lead pot's Avatar
    05-26-2020, 07:46 AM
    That little saw will be the best investment you will ever make cutting down cases. I also use it for cutting copper tubing for making jackets for swaging. The saw is a little tight for working with it if you have big fingers :) but it's a fine...
    18 replies | 317 view(s)
  • Lead pot's Avatar
    05-25-2020, 09:42 AM
    I have a couple tapered bullet moulds and one is from Tom Ballard. I like to shoot without fouling control and with the tapered bullets I can do this. Also my tapered bullets are made for the more or less standard chambers now used that have the...
    5 replies | 1158 view(s)
  • Lead pot's Avatar
    05-16-2020, 10:53 PM
    I run two tumblers and one has the mix of the pins and ceramic. I started this when I came back home after two months on the road out your way and Montana shooting matches. I normally don't clean the cases till I get back home. I take 2000 rounds in...
    25 replies | 1330 view(s)
  • Lead pot's Avatar
    05-15-2020, 11:50 PM
    I use a mix of SST and Ceramic in my Tumblers Tumbler mainly to get the primer pockets cleaner.
    25 replies | 1330 view(s)
  • Lead pot's Avatar
    05-15-2020, 11:05 PM
    Wayne, I use Cascade and SST pins and my cases come out very clean and bright. I don't see a problem with peening and I use a Tumblers Tumbler as well as the Frankfort Arsenal tumbler that turned faster than the tumblers tumbler and it does not...
    25 replies | 1330 view(s)
  • Lead pot's Avatar
    05-13-2020, 08:20 PM
    Since your shooting a TD you are most likely doing it from the muzzle down. Turn the rifle down, trap door down to keep the water from dropping down into the lower parts. You can use a muzzle guide to keep the cleaning rod off the crown and push a...
    37 replies | 3984 view(s)
  • Lead pot's Avatar
    05-11-2020, 08:36 PM
    This post got my curiosity. I'm a fan of the S&W and I never heard of the .32-44 caliber. I did some searching and found a little on this cartridge. The original .32-44 ammo. has the bullet loaded in the case flush with the nose of the bullet even...
    7 replies | 252 view(s)
  • Lead pot's Avatar
    05-11-2020, 07:55 PM
    One thing you can tell him and that is it has some value :) Kurt
    7 replies | 252 view(s)
No More Results
About Lead pot

Basic Information

Date of Birth
September 24, 1939 (80)
About Lead pot
In a State that is #1 with people migrating out.


Total Posts
Total Posts
Posts Per Day
General Information
Join Date

3 Friends

  1. RMulhern RMulhern is offline

    Boolit Master

  2. steve klossing steve klossing is offline

    Boolit Mold

    steve klossing
  3. vikingson57 vikingson57 is offline

    Boolit Bub

Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check