ADvertise hereMidSouth Shooters SupplyTitan ReloadingWideners
Inline FabricationLee PrecisionRotoMetals2Repackbox

  • Multigunner's Avatar
    12-03-2019, 09:23 PM
    Perhaps a Jugged Chamber caused by over torqueing of a poorly prefitted barrel. Do the shoulders look rounded ? Sometimes over torqueing caused stress lines in the chamber area which resulted in bulging of chambers past the receiver ring. This was...
    13 replies | 263 view(s)
  • Multigunner's Avatar
    12-02-2019, 01:30 AM
    IIRC the only airgun suppressors that are not legal everywhere are the detachable metal tube ones over. Those might be removed and adapted to a firearm. The synthetic tubed versions aren't strong enough to withstand fire arms muzzle blast, or so...
    16 replies | 1303 view(s)
  • Multigunner's Avatar
    12-02-2019, 01:21 AM
    Multigunner replied to a thread Daisy model 225. in AirGuns
    Been meaning to reply to this but kept putting it off expecting there would be some posts by others. Anyway I remember seeing one of these years ago. It looked very old when I saw it many years ago so it might have been an earlier incarnation. The...
    1 replies | 391 view(s)
  • Multigunner's Avatar
    11-29-2019, 11:50 PM
    I've reloaded thousands of rounds with a Lee Loader, but the best hand reloading outfit out there is the Lyman 310. Bench Rest shooters used to use the 310 for seating primers because it was so precise compared to bench mounted outfits. I had a...
    17 replies | 625 view(s)
  • Multigunner's Avatar
    11-29-2019, 11:42 PM
    Multigunner replied to a thread Copper clad pellets? in AirGuns
    I've been out of Balistol for awhile and figure most other solvents would eat up seals so I've been soaking the Q-tips in lighter fluid instead. If anything it works better. PS The cut down Q-Tips are fairly stable in flight and if the air or...
    9 replies | 360 view(s)
  • Multigunner's Avatar
    11-29-2019, 08:46 AM
    Multigunner replied to a thread Copper clad pellets? in AirGuns
    That's exactly how I've been doing it. Thought I had hit on something new. The breeches of my air guns don't allow for using a cleaning rod in a normal manner without risking crown damage and even a pull through is hard to use.
    9 replies | 360 view(s)
  • Multigunner's Avatar
    11-20-2019, 02:11 AM
    Commercial sporting .303 cartridge case rims are within specs. Many Military .303 case rims are out of spec by being too thick. Military rifles often have headspace on the loose end of maximum allowable headspace. Older British .303 sporting...
    33 replies | 1747 view(s)
  • Multigunner's Avatar
    11-18-2019, 11:22 PM
    Had the same problem with light loads behind a standard 158 gr bullet in a Colt .38 Special. Later when using an even lighter load behind a round ball a S&W Airweight functioned with no drag at all. I suspect the very light RB load didn't build...
    33 replies | 1747 view(s)
  • Multigunner's Avatar
    11-12-2019, 01:45 PM
    Multigunner replied to a thread Crosman 150 in AirGuns
    Sounds like the striker isn't hitting hard enough to open the valve. My SSP 250 has a similar striker and when left too long in the sun the pressure of the gas is too high for the valve to open. In your situation I expect that when first charged...
    5 replies | 634 view(s)
No More Results
About Multigunner

Basic Information


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 02:22 AM
Join Date

1 Friend

  1. Bob Krack Bob Krack is offline

    Boolit Master at Heavens Range

    Bob Krack
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check