StainLess Steel MediaRotoMetals2WidenersGraf & Sons
Lee PrecisionRepackboxTitan ReloadingMidSouth Shooters Supply
Inline Fabrication
Tab Content
ABJ's Activity
About Me
Tab Content
  • ABJ's Avatar
    10-10-2018, 09:00 AM
    See Post #10. Outpost is dead on. I have used my BP lube on smokeless and it is very,very accurate. One down side is in a revolver the gun is covered in residue after about 50 rounds. 40% bear oil/tallow and beeswax at 60% by volume. Soft in hot...
    18 replies | 810 view(s)
  • ABJ's Avatar
    10-10-2018, 08:38 AM
    I have shot a fair amount of Green Dot under cast 200 swc, H&G 68 style. My load came from some old load manuals so you will have to decide how to proceed. The best accuracy came in at 4.5 grains with my alloy around 14 brinell. I used Lee scoops...
    14 replies | 401 view(s)
  • ABJ's Avatar
    10-10-2018, 08:18 AM
    thks T-Bird, I haven't thought about that. The 4759 is faster than 4198 and I have never been a fan of 4198 in 30's compared to 4759 and 5744 and 2400. I will grab some H335 and might try 4895 speed range powders. Good catch, Thanks Tony
    21 replies | 1014 view(s)
  • ABJ's Avatar
    10-08-2018, 08:55 AM
    We have shot a lot of magma 160 swc. This weight range is short for caliber and has to be pushed a little harder than say a 185 or 200. Our mim. target load is 4.6 grains of Bullseye and accurate out to 50 yds. Other fast pistol powders work as...
    5 replies | 176 view(s)
  • ABJ's Avatar
    10-08-2018, 08:46 AM
    My 311291 throws a .301 nose and will not chamber in any one of my 4-30-30's. It shoots MOA at 100 out of 3 30-06's I have. great boolit if it fits. 311041 will chamber in two rifles,crimped in the crimp groove, and two require crimping about half...
    17 replies | 455 view(s)
  • ABJ's Avatar
    10-01-2018, 03:41 PM
    White Eagle I wish I had time to do that. Between work and all the whatevers I split my time between the pot and the trigger, LOL. I was just hoping I could get that flat nose to work. It would be okay in a factory rifle I'm sure, but I wanted to...
    21 replies | 1014 view(s)
  • ABJ's Avatar
    10-01-2018, 08:16 AM
    updated range report: I had to size the flat point bullet down to .309 to allow a longer OAL. Still not engraving the nose but will engrave the driving band. The throat or freebore is longer than I thought. That boolit is not going to work in this...
    21 replies | 1014 view(s)
  • ABJ's Avatar
    09-27-2018, 07:18 AM
    Thanks RU, I have a hunting buddy that just got a 32 special, model 64 Winchester I think. I am not needing 2000, only 1800 give or take. Good info, thanks for responding. Tony
    21 replies | 1014 view(s)
  • ABJ's Avatar
    09-26-2018, 03:17 PM
    Thanks Guys, I did a brinell test on some of the 50/50 +2 last night and they came in at 11, same as they were at 30 days old. I used coww that BNE tested at 97.1/.3/2.6. I have some older ones that come in with 3.2 antimony, I think I will make a...
    21 replies | 1014 view(s)
  • ABJ's Avatar
    09-25-2018, 05:57 PM
    Lube is commercial carnuba red, a little harder than Glenn's regular. I sized to .313 because on the 314299 pointed it engraved the nose and front driving band. The Flat nosed version at .313 does not engrave the nose just the driving band. Do you...
    21 replies | 1014 view(s)
  • ABJ's Avatar
    09-25-2018, 05:28 PM
    38 special hands down, so many molds and powders it could keep you busy for a long time. Second is the 30-30 from mild to wild, and also lots of molds to choose from on it also. Tony
    27 replies | 593 view(s)
  • ABJ's Avatar
    09-25-2018, 05:14 PM
    I am looking for a simple to make softer than my normal alloy(95.3-2.3-2.6) for 30-06/200 flat nose and 30-30/150 flat nose, all wearing gas checks. I tried the aka-50/50 plus 2, but could only get about 3 to 4 shots before group busting leading...
    21 replies | 1014 view(s)
  • ABJ's Avatar
    09-24-2018, 04:25 PM
    I have cast a lot of large boolits in both pure lead and alloy's. Ladle casting is tough on long boolits. I drilled the spout of an RCBS ladle to allow the lead more head pressure and volume out of the ladle. Pressure casting also worked good. The...
    31 replies | 868 view(s)
  • ABJ's Avatar
    09-20-2018, 03:54 PM
    ABJ replied to a thread Hi All , in Cast Boolits
    Welcome, I hope you like to read (lol). I still haven't seen everything I want to see. The search engine gets you there quick and is easy to use. This is the greatest site ever for casters and shooters alike. The collective knowledge available from...
    34 replies | 799 view(s)
No More Results
About ABJ

Basic Information

About ABJ
Location:
Ball Ground, GA
Interests:
Bullseye and muzzleloading
Occupation:
licensed commercial caster

Statistics


Total Posts
Total Posts
62
Posts Per Day
0.02
General Information
Last Activity
Today 08:30 AM
Join Date
12-04-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check