MidSouth Shooters SupplyLee PrecisionWidenersRotoMetals2
Titan ReloadingInline FabricationADvertise hereRepackbox

Tab Content
ABJ's Activity
About Me
Tab Content
  • ABJ's Avatar
    Yesterday, 04:57 PM
    ABJ replied to a thread Cast in M&P 40 sheild? in Cast Boolits
    Mine is not a 40 but a 9 and it likes lead better than Jacketed, my shooting buddy has two nines and a 45 and they all love boolits. No leading in any of them. I would think the 40 would do the same. Truncated cone noses and rn seem to be more...
    12 replies | 272 view(s)
  • ABJ's Avatar
    Yesterday, 04:50 PM
    This thread was a bear trap. I voted before I looked at the date. oh well. LOL Tony
    62 replies | 8240 view(s)
  • ABJ's Avatar
    03-26-2020, 02:40 PM
    ABJ replied to a thread Lead smelting thermometer in Cast Boolits
    As others have said, the Lyman digital for the price is the best bet. Temps do matter when casting, why guess at it? Tony
    11 replies | 472 view(s)
  • ABJ's Avatar
    03-19-2020, 09:22 AM
    Around 5.5 to 6.0 700x is also my preferred load only because I have more of it than Red Dot. I'm using 150 and 170 boolits. My Winchester 94 is zeroed on the highest iron sight setting on the 700x load and the lowest setting with my deer load at...
    48 replies | 1874 view(s)
  • ABJ's Avatar
    03-18-2020, 09:07 AM
    In my test all at 25 and 50 yards with a scoped Smith/15 here is what I found. First my alloys are 2 tin and 4 antimony and 20:1. I test mostly target loads in the Bullseye 2.8 to 3.2 range. Same with HP-38 from 3.2 to around 4.0. Other powders that...
    21 replies | 1167 view(s)
  • ABJ's Avatar
    03-17-2020, 09:24 AM
    In all my Marlins and Winchesters, .311 has always shot best. Sometimes a .310 but I have never got a .309 to shoot well. The bigger question is the nose and OAL. some of my guns require a .299 nose to chamber if crimped in the crimp groove. My...
    18 replies | 1352 view(s)
  • ABJ's Avatar
    03-17-2020, 08:54 AM
    Bill*B makes a good point. The only time I do it is when the OAL needs to be shorter, then I adjust the powder charge accordingly. My normal is if it has a crimp groove I use it. If I'm not getting the accuracy I want I then move the powder charge...
    10 replies | 688 view(s)
  • ABJ's Avatar
    03-17-2020, 08:38 AM
    I have noticed in my Redhawk, increments of 2/10ths and adjusting crimps can make a lot of difference in accuracy. I have some H-4227 left over and a little less recoil than 2400, but 2400 delivered top notch accuracy. I'm at work and don't have my...
    33 replies | 1692 view(s)
  • ABJ's Avatar
    03-12-2020, 08:17 AM
    I cast pure tin in a Lee 6c 45-200tl mold. pure tin is hard to cut if too cool. Once it warms up it is fine. I would think that your mix should be a little softer than pure tin. FYI a 45/200 pure tin is .02 pounds each. Until the mold and sprue...
    24 replies | 1712 view(s)
  • ABJ's Avatar
    03-09-2020, 09:38 AM
    Send a sample to member "BNE". Get the alloy calculator from this site and under custom alloys punch in the xrf readings and you can make anything you wish very accurately. I could not even think of not using the alloy calculator. Tony
    9 replies | 665 view(s)
No More Results
About ABJ

Basic Information

About ABJ
Location:
Ball Ground, GA
Interests:
Bullseye and muzzleloading
Occupation:
licensed commercial caster

Statistics


Total Posts
Total Posts
121
Posts Per Day
0.03
General Information
Last Activity
Yesterday 05:01 PM
Join Date
12-04-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check