Titan ReloadingLee PrecisionRotoMetals2StainLess Steel Media
Graf & SonsMidSouth Shooters SupplyADvertise hereInline Fabrication

Tab Content
  • tiger762's Avatar
    09-10-2017, 10:10 PM
    tiger762 replied to a thread Le!d pot for annealing in Swaging
    Yep, this is the correct answer. I have been making a bunch of 458 lately using 45acp brass. I don't even bother annealing the brass. Pushing it through the reducer die does require more torque :D and would buckle horribly if I was making a hollow...
    21 replies | 1988 view(s)
  • tiger762's Avatar
    09-03-2017, 07:32 PM
    I just measured one of mine. The length is 1.38". Flat base. Copper disk in base. A lead-core bullet this long would usually be more like 200 grains. I think they would be difficult to counterfeit, as long as one could see them in person.
    18 replies | 857 view(s)
  • tiger762's Avatar
    09-03-2017, 07:23 PM
    Everyone wants things dirt cheap.
    32 replies | 1179 view(s)
  • tiger762's Avatar
    09-03-2017, 07:21 PM
    tiger762 replied to a thread My little housework. in Swaging
    Holy cow! You're like the first person I know that has made his own shell casing :O
    38 replies | 1825 view(s)
  • tiger762's Avatar
    08-31-2017, 05:58 PM
    Gunbroker always has someone selling them. They go for $1 each.
    18 replies | 857 view(s)
  • tiger762's Avatar
    08-26-2017, 09:33 PM
    I have 100,000+ fired 9mm, hand sorted, no aluminum or steel although some nickel (13+ 5 gallon buckets). I'll value the brass at whatever scrap value currently is. Ideally, I need pure lead to cast cores for swaging. The lead to me is worth $1 a...
    10 replies | 476 view(s)
  • tiger762's Avatar
    08-26-2017, 09:24 PM
    Both definitions are predicated on it being used in a "handgun". Seems like one could make AP rifle rounds all day long. Ones that are not gray-area dual use (handgun and rifle). No one would ever imagine a handgun designed around the 30-378, for...
    32 replies | 1179 view(s)
  • tiger762's Avatar
    08-25-2017, 06:48 PM
    That will happen in most if not all un-annealed brass. If you run the seated core/jacket into the point form die *** end first, the resulting FMJ style will not have this problem. I've been making a bunch of 62gr FMJ lately. No annealing necessary....
    23 replies | 5450 view(s)
No More Results
About tiger762

Basic Information

About tiger762
Location:
NE Georgia

Statistics


Total Posts
Total Posts
373
Posts Per Day
0.13
General Information
Last Activity
Yesterday 08:35 PM
Join Date
11-23-2009
Referrals
1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check