Lee PrecisionADvertise hereRotoMetals2Repackbox
Inline FabricationTitan ReloadingMidSouth Shooters SupplyWideners

  • ReloaderFred's Avatar
    Today, 05:09 PM
    I've ruined many a great group with a second shot.............:bigsmyl2:
    7 replies | 166 view(s)
  • ReloaderFred's Avatar
    Today, 01:53 PM
    Slave pins are definitely required to put a Model 88 trigger group back together. I'm told it can't be done without them. There are some Youtube videos on the Model 88 available, if someone really wants to tear into one. Hope this helps. Fred
    8 replies | 228 view(s)
  • ReloaderFred's Avatar
    Today, 02:16 AM
    No gunsmith in his right mind wants to tear one apart. I had a so-called gunsmith call me and want to borrow my Winchester 88, since he had one apart and couldn't get it back together. I asked him why he wanted mine, and he said he wanted to take...
    8 replies | 228 view(s)
  • ReloaderFred's Avatar
    Yesterday, 11:59 AM
    The problem would be in getting enough grip on the bullet to impart spin from the rifling. Sabots are normally made from a plastic that is more "grippy" than the slick plastic the Speer capsules are made from. The plastic the capsules is made from...
    6 replies | 205 view(s)
  • ReloaderFred's Avatar
    04-01-2020, 08:06 PM
    That combination wouldn't have "nested", and would have been fine to tumble together. You may get a few .38's stuck on the neck of some .30-30's, but it wouldn't have been a big deal. Hope this helps. Fred
    39 replies | 1595 view(s)
  • ReloaderFred's Avatar
    04-01-2020, 12:54 PM
    I use Magma lube for just about everything, and it's a hard lube. If you're using a softer lube, it may flow more than a hard lube does. Hope this helps. Fred
    13 replies | 308 view(s)
  • ReloaderFred's Avatar
    04-01-2020, 01:31 AM
    I've changed the shape of many cast bullets in my swaging dies. I just lube as normal, then swage. The lube stays in place and holds the lube groove open, as garandsrus mentions. It's super quick and works well. Hope this helps. Fred
    13 replies | 308 view(s)
  • ReloaderFred's Avatar
    03-31-2020, 04:22 PM
    10mm / 40 S&W 3 die set by Dillon $40 I'll take this. PM inbound.
    10 replies | 821 view(s)
  • ReloaderFred's Avatar
    03-31-2020, 01:05 PM
    If you look at a new primer from the side, you'll notice that the legs of the anvil are set slightly above the lip of the primer cup. This is done by the factory on purpose. When a primer is properly seated, it will be all the way to the bottom of...
    27 replies | 509 view(s)
  • ReloaderFred's Avatar
    03-27-2020, 08:38 PM
    I've got three of them, and 9 or 10 rotors. They're a handy little measure for small cartridges. Hope this helps. Fred
    20 replies | 450 view(s)
  • ReloaderFred's Avatar
    03-27-2020, 11:28 AM
    One way to prevent two different size cases mating like that, and still being able to tumble them together, is to put the largest cases in first. Let the tumbler run for a minute to fill the larger cases with media, and then dump in the smaller...
    39 replies | 1595 view(s)
  • ReloaderFred's Avatar
    03-27-2020, 12:59 AM
    Some debris got caught between the stop rod and the edge of the hole and kept it partially open. It never happens at a good time, but turn your back for a minute and that's when it's going to pounce. Hope this helps. Fred
    12 replies | 317 view(s)
  • ReloaderFred's Avatar
    03-26-2020, 01:23 AM
    skeettx beat me to it. Put them in the tumbler minus media and let the vibration do it's thing. Hope this helps. Fred
    39 replies | 1595 view(s)
More Activity
About ReloaderFred

Basic Information

About ReloaderFred
Biography:
I've been reloading and casting bullets since 1963.
Location:
Oregon Coast
Occupation:
Retired

Signature


After a shooting spree, they always want to take the guns away from the people who didn't do it. - William S. Burroughs.

Statistics


Total Posts
Total Posts
6,307
Posts Per Day
1.21
General Information
Last Activity
Today 08:14 PM
Join Date
12-17-2005
Referrals
2

5 Friends

  1. 7of7 7of7 is offline

    Boolit Master

    7of7
  2. BLASTER62 BLASTER62 is offline

    Boolit Buddy

    BLASTER62
  3. km101 km101 is offline

    Boolit Master

    km101
  4. Roundnoser Roundnoser is offline

    Boolit Master

    Roundnoser
  5. wymanwinn wymanwinn is offline

    Automated Master Caster

    wymanwinn
Showing Friends 1 to 5 of 5
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check