MidSouth Shooters SupplyADvertise hereInline FabricationRepackbox
RotoMetals2Lee PrecisionWidenersTitan Reloading

  • km101's Avatar
    Yesterday, 10:01 PM
    km101 replied to a thread Red Neck yard art in Our Town
    My “by the rule book” mail carrier would have a stroke if I put out something like that, but I LIKE it!
    11 replies | 499 view(s)
  • km101's Avatar
    Yesterday, 09:51 PM
    km101 replied to a thread Missing: Cardinals in Our Town
    We even have a few cardinals here in the Lone Star State. Last spring a pair nested in our plum tree. They ran our young cat back into the house from the back yard. Now he sits on the patio and looks carefully to be sure they’re not around before...
    40 replies | 749 view(s)
  • km101's Avatar
    Yesterday, 09:22 PM
    km101 replied to a thread Snow???? in Our Town
    Snow???? Yep, about every 2-3 years. And everyone goes nuts! Schools close, businesses close and all the grocery stores run out of milk and bread. (are they making milk sandwiches?). And the snow usually only lasts for a day or two. If it’s a...
    25 replies | 515 view(s)
  • ReloaderFred's Avatar
    Yesterday, 01:10 PM
    Erik sometimes has extras, or he can convert just about any mold you have to cast hollowpoint bullets. Here's the link to his site: http://www.hollowpointmold.com/ Hope this helps. Fred
    1 replies | 118 view(s)
  • ReloaderFred's Avatar
    12-06-2019, 12:39 AM
    The SAAMI standard is 1.155" - .020". https://saami.org/technical-information/cartridge-chamber-drawings/ You don't state what the exact measurement of your brass is. With revolver brass, as long as they're all the same, the length isn't that...
    13 replies | 350 view(s)
  • ReloaderFred's Avatar
    12-06-2019, 12:26 AM
    Yes, I own ten Star sizers, but three of them are on "lifetime loan" to really, really good friends. I have one sitting idle at the moment, but as soon as I finish rebuilding the heater base that had been in a bucket of water for who knows how...
    10 replies | 1397 view(s)
  • ReloaderFred's Avatar
    12-05-2019, 12:43 AM
    I buy them all the time at gun shows and off the auction sites. I just throw them in the tumbler and let them run until they're clean. If they're heavily encrusted, I hit them with a wire toothbrush prior to tumbling. It saves on a lot of extra...
    21 replies | 1340 view(s)
  • ReloaderFred's Avatar
    12-05-2019, 12:40 AM
    They had the new design at the SHOT Show this past January, and I asked the rep if this one would resist melting and becoming discolored. He said it would and to call their service department for a replacement. Hope this helps. Fred
    19 replies | 1012 view(s)
  • ReloaderFred's Avatar
    12-04-2019, 11:34 AM
    Contact Hornady direct by phone. They have a new hopper that solves that problem, and they'll probably send it to you for free. Hope this helps. Fred
    19 replies | 1012 view(s)
  • ReloaderFred's Avatar
    12-03-2019, 12:52 AM
    I've seen it first hand in a Model 73 Winchester, and I've seen pictures of a Model 94 Winchester that was destroyed by a magazine detonation.
    16 replies | 1229 view(s)
  • km101's Avatar
    11-30-2019, 02:30 PM
    Only 2! I noticed this some time ago.
    25 replies | 1398 view(s)
  • km101's Avatar
    11-28-2019, 09:58 AM
    Happy Thanksgiving! Let’s all give thanks to The Lord for our many blessings! Enjoy your family and friends and most of all, be safe!
    19 replies | 784 view(s)
  • ReloaderFred's Avatar
    11-27-2019, 01:28 AM
    Courtesy bump.
    5 replies | 392 view(s)
  • ReloaderFred's Avatar
    11-25-2019, 02:23 PM
    They would make an excellent bullet for the .30 Carbine Ruger Blackhawk, since it doesn't matter what the bullet shape is for a revolver, as long as it can fit in the cylinder. Hope this helps. Fred
    5 replies | 898 view(s)
  • ReloaderFred's Avatar
    11-23-2019, 08:47 PM
    Congratulations on a rare find, Pressman. Now, if that old girl could only talk........
    7 replies | 593 view(s)
  • ReloaderFred's Avatar
    11-23-2019, 02:30 AM
    The primers probably weren't seated properly, if they were reloads. Other than that, heat and humidity may have killed them. If he pulled down some that didn't go off, and the powder is contaminated, that could be a reason, but the orientation...
    20 replies | 1742 view(s)
More Activity
About ReloaderFred

Basic Information

About ReloaderFred
Biography:
I've been reloading and casting bullets since 1963.
Location:
Oregon Coast
Occupation:
Retired

Signature


After a shooting spree, they always want to take the guns away from the people who didn't do it. - William S. Burroughs.

Statistics


Total Posts
Total Posts
5,536
Posts Per Day
1.08
General Information
Last Activity
Today 02:03 PM
Join Date
12-17-2005
Referrals
2

5 Friends

  1. 7of7 7of7 is offline

    Boolit Master

    7of7
  2. BLASTER62 BLASTER62 is offline

    Boolit Buddy

    BLASTER62
  3. km101 km101 is offline

    Boolit Master

    km101
  4. Roundnoser Roundnoser is offline

    Boolit Master

    Roundnoser
  5. wymanwinn wymanwinn is offline

    Automated Master Caster

    wymanwinn
Showing Friends 1 to 5 of 5
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check