Lee PrecisionInline FabricationRotoMetals2Graf & Sons
StainLess Steel MediaADvertise hereTitan ReloadingMidSouth Shooters Supply

Tab Content
  • bob208's Avatar
    Yesterday, 11:51 AM
    it can be done but the work involved unless you are doing it your self is very expensive. you bore out your existing chamber press in a sleeve and chamber it to the smaller cartage.
    16 replies | 184 view(s)
  • bob208's Avatar
    04-22-2018, 10:16 AM
    when I was shooting ppc with my security six. I used the rcbs tc bullet with 3.5gr. red dot. the tc made loading with a speed loader faster.
    7 replies | 198 view(s)
  • bob208's Avatar
    04-18-2018, 09:31 PM
    back in the 80's I worked for a gov. contractor. they would sign out a file swipe the al. armor plate choke it up it would go right in the trash I would fish them out along with the taps. still using those files and taps today.
    46 replies | 1170 view(s)
  • bob208's Avatar
    04-17-2018, 09:54 AM
    bob208 replied to a thread Spring? in Our Town
    took the trailer up to the Carlisle pa. spring car show yesterday. setting here now by the wood stove watching snow flurries.
    41 replies | 655 view(s)
  • bob208's Avatar
    04-12-2018, 05:31 PM
    bob208 replied to a thread 1866 Uberti in Leverguns
    I have had this problem with some guns. I did some head scratching and checking . I was using a wheel gun when I had a tight one going inone hole I tried it in another. then I started looking and measuring. found the cases that were tight in the...
    12 replies | 326 view(s)
  • bob208's Avatar
    04-11-2018, 01:02 PM
    check the thread size and drill and tap a bar of steel to fit. this is not rocket science.
    13 replies | 281 view(s)
  • bob208's Avatar
    04-08-2018, 11:33 PM
    where I am in pa. evert fourth house has a bench and back stop. some are 50 yd. some are 2-300 yds. our farm I have a 50 and 100 yard. but for hand gun or quick testing I shoot right off the back porch. thn there are private clubs every where.
    54 replies | 1666 view(s)
  • bob208's Avatar
    04-08-2018, 07:30 PM
    the side holes for a receiver sight were not drilled till 1950's. also to put the 71 butplate on the end of the stock would have to been sanded flat.
    11 replies | 496 view(s)
  • bob208's Avatar
    04-06-2018, 09:13 PM
    short answer NO. go you like to lose money? a refinish will cost you twice once for the job and then ifor when you try to sell it.
    22 replies | 527 view(s)
  • bob208's Avatar
    04-06-2018, 09:07 PM
    .50-110 is the express load for the .50-100. I have a box of .50-110-350s in my collection.
    26 replies | 1015 view(s)
  • bob208's Avatar
    04-06-2018, 08:55 PM
    if paying collector price then it should be collector grade. the one you looked at is not collector grade.
    11 replies | 496 view(s)
  • bob208's Avatar
    04-05-2018, 06:50 PM
    I have a 92 rebuilt to 96 spec. a early 96 rifle with the nonadjustable windage rear sight. a 96 with the later adjustable rear sight. 2 98s one with the 1901 sight. 1 96 saddle ring carbine 1 98 saddle ring carbine and a 99 carbine I killed a 8...
    23 replies | 1135 view(s)
  • bob208's Avatar
    04-05-2018, 02:25 PM
    too many muzzleloaders ??? that is like a horse to fast whiskey too old or a girl too pretty.
    24 replies | 975 view(s)
  • bob208's Avatar
    04-05-2018, 02:17 PM
    bob208 replied to a thread Dash Camera in Our Town
    after dodging idiots on cellphones and the break checks we got one for my truck and the wife's truck. also works good for the fools that run up beside you and try to cut over when the lane ends. the stepsons company put them in all their trucks....
    26 replies | 1037 view(s)
  • bob208's Avatar
    04-01-2018, 09:46 PM
    you are plug over thinking this simple repair. just drill the hole out to the next larger size plug it with a loc-tight. then redrill to the right location. I have done this many times. never had one fail. do use fine threads
    13 replies | 528 view(s)
  • bob208's Avatar
    04-01-2018, 11:24 AM
    bob208 replied to a thread Our government in action in Our Town
    tractor supply has nozzles for some of the older cans also I get a lot off ebay. I pick up all the old style gas cans at auctions and yard sales with missing caps and spouts.
    38 replies | 1143 view(s)
More Activity
About bob208

Basic Information

About bob208
. was a certified weldor for 30 years. then learned toolmaking.
gardners pa.
blackpowder gunsmithing. shooting matchs classic cars and trucks.
retired. now i have time for my own machine weld shop. many projects to try to finish


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 11:28 PM
Join Date

1 Friend

  1. FLHTC FLHTC is offline

    Boolit Master

Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check