ATTENTION! A new MiHec four cavity brass mould in .44

[Dale53]

There has been a lot of interest in running the H&G #503 .44 Caliber Keith again, but in a four cavity brass mould. I have "talked" to MiHec and he is prepared to do this for us. It will cost $85.00 plus $20.00 shipping. The minimum number is fifteen. There will be no "beating around the bush" - I will start immediately to sign people up. I will run this for six weeks. Here is what it looks like (MiHec will use the original tooling that he used on the six cavity aluminum mould):

http://i269.photobucket.com/albums/jj80/Dale53/Dales_44_2009_05_09.jpg

http://i269.photobucket.com/albums/jj80/Dale53/DALES44_20090509_SMALLAD_DRW_0001.png

We have "Long bow" to thank for the computer generated picture and drawing.

Good people, this is rare opportunity to get another of MiHec's four cavity brass moulds for this fine Keith SOLID bullet. I have the original six cavity aluminum mould and use it regularly. After using MiHec's brass moulds, I now have a "thing" for them (many of you have expressed the same attitude). This is certainly one of the finest performing Keith bullets available, anywhere, for the .44 Special and .44 Magnum.

Please sign up with your Forum name and Email address (camouflage your Email address as I have done).

The list starts NOW!

1 - Dale53 - rmcgee at zoomtown.com - one mould
2 - Heavy lead - steve cartwright at amerifirst dot com - one mould
3 - chprplt -exit13five at aol dot com - two moulds
4 - Zeus - gswaggart at hotmail dot com - One Mould
5 - Taugust - g99jeb at aol dot com - one mould
6 - GLL - gllewis at pasadena dot edu - one mould
7 - Cast-n-Blast - jeffrey dot hoover at montgomerycountymd dot gov - one mould
8 - John D - wa2eya at verizon dot net - one mould
9 - Ricky P - rickyparchman at yahoo.com - one mould
10 - Matt_G - mgoodrich (at) 4dv (dot) net - one mould
11 - Alamogunr - alamogunr(at)charter(dot)net - one mould
12 - 67bear - gvest67 at yahoo dot com - one mould
13 - Rico1950 - RSB 1913501 at yahoo dot com - one mould
14 - AKtinman - aardvark at netcommander dot com - one mould
15 - ce1911 - dtoman at bis dot midco dot net - one mould
16 - Big Dale - Brimbum at AOL dot com - one mould
17 - 38wcf - cvcooks at astound dot net - TWO MOULDS
18 - GMSharps - gmsharps at cs dot com - one mould
19 - Fowler - bfowler at wescolaser dot com - TWO MOULDS
20 - Fugowii - fugowii at gmail dot com - one mould at .434"
21 - Paulinski - pkrysztofiak at gmail dot com - one mould
22 - Blammer - vmthtr at charter dot net - one mould
23 - 2 dogs - fcgarza 0640 AT hot mail DOT com TWO MOULDS at .434"
24 - Bushwaker - sprayman2007 at comporium dot net - one mould
25 - Lonewelder - lonewelder at msn dot com - one mould
26 - Wots - WotsamtrU at aol dot com - one mould
27 - DGV - deano1860 at aol dot com - one mould
28 - rivane33 - ivanrogers at hotmail dot com - one mould
29 - JDUBS - jessdog19 at hotmail dot com - one mould
30 - 2003Viper - vernhinshaw at northstate dot net - one mould
31 - PH4570 - videodog at comcast dot net - one mould
32 - Gavetta - recka at reckaassociates dot com - one mould
33 - AnthonyB - anthonybennett __ comcast ___ net - one mould
34 - Salmon Boy - salmon-boy using comcast for net - one mould
35 - Von Dingo - marc Underscore montpetit at hot mail dot com - one mould
36 - Body Doc447 - bodydoc447 at aol dot com - one mould
37 - Clyde - cpeer at charter.net - one mould
38 - backed out
39 - captaint - roctober5th at gmail dot com - one mould
40 - newrugersafan - stobbmataoldotcom - one mould
41 - Jeff_WNY - Jeff_WNY - castboolits AT lockport DOT net - TWO MOULDS
42 - SteveP - sjjp at windstream dot net - one mould
43 - EDK....ed dot kayser at yahoo dot com - one mould at .434"
44 - c.r. - carroll.r.adams at gmail dot com - one mould
45 - ddeaton - ddeaton at zoomtown dot com - one mould
46 - joeb4065 - jburson101 at yahoo dot com - one mould
47 - CBH - cwhite86-earthlink-net - one mould
48 - Swindler1 - dandbohio at aol dotcom - one mould
49 - RedHawk357mag - RedHawk357Mag at Gmail dot com - one mould
50 - Doc Highwall - highwall at cox dot net - one mould at .434"
51 - Muckman - pete.connie at live.com - one mould
52 - WMB30 - wmb30atatt.net - pne mould
53 - fivegunner - fivegunner at sbcglobal dot net - one mould
54 - Alex - alexdoug at sbcglobal dot net one mould
55 - IowaFox - slvfx50 at aol dot com - one mould
56 - Bob J - Bob dot Johnson at Invensys dot com - one mould
57 - wdr2 - wrichins at gmail dot com - TWO MOULDS
58 - Rodfac - dloberg at bellsouth dot net - one mould
59 - Manomet - lebconstruction at gmail dot com - one mould
60 - nueces44 - r7277c at yahoo dot com - one mould
61 - DukeinMaine - paypal .... atta .... sebagosales..... dotta ..... com... unications......one mould
62 - Cbrick - Rick at lasc dot us - one mould
63 - Chuckbuster -chuckbuster at Hotmail dot com - one mould
64 - beerloaf - mhickok at gmail dot com - one mould
65 - Swiss 96/11 - bigrockfish7 at aol dot com one mould at .434"
66 - JBLee10 - jblee10 at hotmail dot com - one mould
67 - Harlow Parkenfarker - BDCONNON at PACINFO dot COM - one mould
68 - Farky - fishhawk21(at)hotmail(dot)com - one mould
69 - Oscarflytyer - myerssw at knology dot net - one mould
70 - Daddyfixit - icmacfamily At hOt MaIL Dott cOm - one mould
71 - Shortbbl - shortbbl at gmail dot com - one mould
72 - kirb - kdkirby at icsofidaho dot com - one mould
73 - LAH - lah at suddenlink dot net -TWO MOULDS
74 - johnvid - jvidmar at roadrunner dot com - one mould
75 - 29yearsreload - apalsmei at pixius dot net - one mould
76 - Ramslammer - namovlov at bigpond dot com - one mould
77 - 101VooDoo - 101voodoo at sbcglobal dot net - one mould
78 - wired54 - wired54 at gmail dot com - one mould
79 - sljacob - sljacob at allwest dot net - one mould
80 - canyon-ghost - 3rdshooter at att dot net - one mould
81 - JohnnyCyclone - robertditsimonatcoxditnet - one mould
82 - CPTI - michael dot iannuccilli @ hotmail dot com - one mould
83 - Cadillo - cadillo2 at att dot net - one mould
84 - emj - ejansen2410 at gmail dot com - one mould at .434"
85 - CHBoats - boatmanc at yahoo dot com - one mould
86 - zac0419 - zac0419 at msn dot com - one mould
87 - pack3480 - dcasad at hotmail dot com - TWO MOULDS
88 - Calehedron - kenneth dot ferry at gmail dot com - one mould
89 - Practical Man - 1practical [dot] man [at] gmail [dot] com - one mould
90 - Fobis01 - csmith3 at vtown dot com dot au - one mould
91 - Blazenet - Blazenet AT Comcast dot net - one mould
92 - Mal Paso - 429421 at gmail dot com - one mould
93 - Cats - one mould
94 - MtMark45 - mlkeith 45@ aol.com - one mould
95 - foxtrotter - foxtrotter at rtci dot net - one mould
96 - That'll Do - bron_yr_aur (at) comcast (dot) net - one mould
97 - Eastwa - eastwa78 (AT) msn (DOT) com - one mould
98 - Mak Rov - gmctrk at comcast dot net - one mould
99 - sleeper 1428 - sleeper1428 at charter dot net - one mould
100 - JimmyDee - jdavitt at gmail . com - one mold
101 - donnie45 - donniem at macc dot edu - one mould
102 - Patman - jeepat3atqdotcom - one mould
103 - USAF SHIRT - prkaiser1 (at) yahoo (dot) com - one mould
104 - Bpost1958 - bpost58 at Frontier DOT com. - one mould
105 - Dang - adgrime at catt dot com - one mould
106 - critterkillr - krslates at live dot com - one mould
107 - gunsbrad - bradhurt2 at yahoo dot com - one mould
108 - hamour - hank (dot) austin (at) saudichevron (dot) com - one mould
109 - Alan - aatwood2 at tx dot rr dot com - one mould
110 - Gregger - socr4all at yahoo dot com - one mould
111- Retired Navy - jwmoore at sbcglobal dot net - one mould
112 - 310Pilot - jimflys310 at yahoo dot com - one mould
113 - Onty - ibcdiesel at netscape dot net - one mould
114 - lurch - kurthesse at embarqmail dot com - one mould at .434"
115 - 500bfrman - merrilllangs at gmail dot com - one mould - .434"
116 - breathed - breathed99 at yahoo dot com - one mould
117 - sargeny1 - Sargeny1 at verizon net - one mould
118 - tcart - tcart at hotmail dot com - one mould
119 - Sliphammer - salmtruttaataoldotcom - one mould
120 - badluther - boomercowboy at gmail dot com - one mould
121 - 44 Shooter - ajspan at msn dot com - one mould
122 - Potsy - brianwestwwathotmaildotcom - one mould
123 - man.electric - jimbighed at yahoo dot com - one mould
124 - MGySgt - MGySgt4099@Hotmail.com - one mould
125 - DLM - miller448 at aol dot com - one mould
126 - Back Woods Billy - wjcampbell1954 at yahoo dot com - one mould
127 - Sagebrush7 - jamessage at bellsouth dot net - one mould
128 - Ilwil - william.bentler1 at frontier dot com
129 - bburnz - bburnz at pixius dot net - one mould at .434"
130 - Princeout - princeout at sbcglobal dot net - one mould
131 - Rogsir - rogsir at gmail dot com - one mould
132 - Garand 4 - douglee55@hotmaildotcom - one mould
133 - dr-reloader - one mould
134 - hporter - hporter 67 at mac dot com - one mould
135 - was1911 - was1911 at bellsouth dot net - one mould
136 - Ward 0 - wolson at rfgdistributing dot com - one mould
137 - Suo Gan - randolphscott257 at gmail dot com - one mould
138 - CHD - codyhuck at gmail dot com - one mould
139 - CSH - showard at newsguy.com - one mould at .434"
140 - 500ASquare - tphilgig at yahoo dot com - TWO MOULDS
141 - idmcrook - mjcrookston at msn.com - one mould
142 - johnny356mr - johnandsuzi at msn dot com - one mould
143 - swissham - johnbrown -at- triad-dot-rr-dot-com - one mould
144 - M-Tecs - jjkar15 at comcast dot net - one mould
145 - buckndee - 2hunters2 at comcast dot net - one mould
146 - mike454 - mike454 at gmail dot com - one mould
147 - GMW - GMW harley2002 at epix dot net - one mould
148 - akriet - akriet at bellsouth dot net - one mould
149 - 4719dave - davebz63 at aol dot com - one mould
150 - reader - reader452 at gmail dot com - one mould
151 -




Dale53

[Heavy lead]

I'm in, as noted before, his aluminum is my favorite and my 44's favorite mould.

[chprplt]

I'm in for two, maybe a third as a gift. thanks Dale.

[chprplt]

Sorry, I got excited....
chprplt, exit13fiveataol.com, two molds, plain base

[Dale53]

chprplt;
Yep! This is all your fault!:mrgreen: Truth is, I wanted it to happen, also.

Heavy Lead - we need your camouflaged Email address.

Dale53

[Heavy lead]

steve cartwright at amerifirst dot com

:veryconfu:veryconfu:veryconfu:veryconfu

[Zeus]

I'm in for two. Thanks again Dale!

gswaggart at hotmail dot com

[taugust]

I'll take one!

g99jeb at aol dot com

Thank you.

Tom

[GLL]

One for me as well ! :) :)

Jerry

[Dale53]

Zeus: you are in for two moulds.

Taugust - you are in for one mould.

GLL - you are in for one mould (I thought I would see you here, Jerry:mrgreen: By the way, I need your current Email address (please camouflage it like the others).

Good show, good people. It looks like this one is rollin'!

Dale53

[500bfrman]

when would this need to be paid for. said run the gb for six weeks. that puts at about thanksgiving.

[DukeInMaine]

Unlike the NOE molds, M-P Molds will send you an invoice DIRECTLY when the molds are finished, and that's when you pay.

I like that system a lot, and hope that it eventually becomes the way NOE also does their molds.


when would this need to be paid for. said run the gb for six weeks. that puts at about thanksgiving.

[500bfrman]

I know my problem is I am just so overspent and most of it to Mihec. I bout one of the 434640 or something like that overruns. I am in for both of the 500 smith molds right now. I bought four guns in august, and one on layaway, out next month. If we think this will be done this year I can't get in. but if it crept into january I am in.

[cast-n-blast]

Dale, I'm in ! hoover0588 at aol dot com

[John D]

I missed the original 6 cav. aluminum mould. I'm not gonna miss this one!

Put me down for one mould.

wa2eya at verizon dot net

[RP]

Dale this is one of the best easiest to read buy I seen cut and dry I would like one also
rickyparchman at yahoo.com Hes got to stop making molds for awhile so I can regroup just got one two more in the mail coming my way now this one. I also like the way he takes payment Keeps it in a two party deal less to get confused or lost. Thanks dale.

[GLL]

Dale:

Thanks for running this one !

Jerry

gllewis at pasadena dot edu

[Hickory]

Boy, I'd like to get in on this , but I don't have a paypal account and do not want to get a paypal account.
I e-mailed MiHec once about taking an international money order, but recieved no reply.
Oh, well. I guess I miss out again.:cry:

[Matt_G]

Hickory, you can pay Mihec via AlertPay (https://www.alertpay.com/en/Default.aspx) as well.
Take a look and see if that would be a viable option for you.

[Dale53]

Dale:

Thanks for running this one !

Jerry

Happy to do it, Jerry.

Hickory;
Would sure like to have you aboard. I find PayPal to be as easy as can be. I give them my credit card number and that's all there is too it. It's simple and easy and costs me nothing. I realize that they ask for your bank information - I don't give them my bank information. No problem whatsoever. MiHec gets his money instantly and I get my mould at the earliest possible time.

If you change your mind, let me know and I'll get you on the list.

Dale53

[Matt_G]

I want one mould as well Dale.

mgoodrich (at) 4dv (dot) net

Miha's gonna bankrupt me! That's all right though.
It's just money. Not like I can take it with me. :lol:

[Dale53]

Matt_G;
You are on the list. Welcome aboard!

We now have thirteen moulds on order. It only takes fifteen to make this a GO!

Way to go, folks!

Dale53

[Hickory]

Dale53 and others,
Call me old fashion or skitzo, but I just can't
bring myself to put my cc# on the computer to buy stuff.

[alamogunr]

OK! Now that my .45's are taken care of, I am ready to commit to feeding my .44's. I don't really need this one since I've got several .44 molds from other GB's but the 4 cavity brass molds are too pretty to pass up.

alamogunr(at)charter(dot)net

John
W.TN

[67bear]

Please put me down for one.

gvest67 at yahoo dot com

Thanks

[Matt_G]

Wow, hit the magic 15 in less than seven hours. :holysheep


Dale53 and others,
Call me old fashion or skitzo, but I just can't
bring myself to put my cc# on the computer to buy stuff.

Hickory, I can understand that.

[Salmon-boy]

Is this going to be a hollow point cramer mould? If so, I'm DEFINITElY in, otherwise..

Hey, wait, I don't even have a .44.. But it's a Mihec mould.. Oh decisions, decisions..

Ok, I'm in.

[Rico1950]

I'm in for one also.
RSB 1913501 at yahoo dot com

[AKtinman]

I'll take one!

aardvark at netcommander dot com

Thanks for doing this one!

[Dale53]

Salmon-boy;
This is a MiHec four cavity brass mould for the Keith SOLID bullet. Let me know if you are in (I will need your Email address - camouflage it like the others).

MattG;
Yeah, this one is taking off! I am happy to see that. Apparently, a lot of us feel the same about these fine moulds...

Aktinman;
You are on the list! Welcome to ALL!

Dale53

[ce1911]

I will take one.

dtoman at bis dot midco dot net

[big dale]

I need one of these molds. Big Dale-Brimbum at AOL dot com

I just love brass molds and I only have two other molds for this boolit...so put me dwn for one of these. What a great Christmas gift

Big Dale

[358wcf]

Gotta have this one!
Yes, I'm addicted to MP molds- I see 4 on the bench right now. One more certainly won't hurt, and I am in love with brass molds-
One mold, please-
MP molds certainly make our Lyman, Lee, and RCBS molds look crude by comparison.

cvcooks at astound dot net

Thanks,

358wcf [smilie=1:[smilie=1:[smilie=1:

[kbstenberg]

If i got a third mold in the same bullet my wife would make me live perm. in the wellshed! I like casting but not that much.
Kevin

[Dale53]

ce1911, big dale, and 358wcf: Happy to have you fellers aboard!

kbsttenberg; We understand, fully. However, if you change your mind, just let me know. We would love to have you with us!

Nineteen and still counting...[smilie=w:

Dale53

[Zeus]

I knew it wouldn't take long to get a bunch of these on the list. I like to see a fast response like this, I wonder what the total will be in six weeks :) :)

[rollmyown]

Times like this I wish I had a .44 :violin:

[gmsharps]

I'll take one

gmsharps at cs dot com

Thanks

[Fowler]

I'm in for two please!

bfowler at wescolaser dot com

[Fugowii]

I'm in.

[John D]

Times like this I wish I had a .44 :violin:


You supposed to buy the mould before the gun. This way, you have a valid reason for buying the gun! :kidding:

[Paulinski]

I'll take one please.

pkrysztofiak at gmail dot com

[Blammer]

Put me down for one.

vmthtr at charter dot net

[Dale53]

GMSharps, Fowler, Fugowii, and Paulinski, welcome to the bunch! Happy to have you sign up.

Blammer, welcome aboard!

Blammer and Fugowii - we need your Email address! Camouflage it like everyone else on the list.

We now have twenty-five moulds spoken for!! Way to go, folks!!:drinks:

Dale53

[Fugowii]

GMSharps, Fowler, Fugowii, and Paulinski, welcome to the bunch! Happy to have you sign up.

Blammer, welcome aboard!

Blammer and Fugowii - we need your Email address! Camouflage it like everyone else on the list.

We now have twenty-five moulds spoken for!! Way to go, folks!!:drinks:

Dale53

fugowii at gmail dot com

[Dale53]

Fugowii;
Thanks for the quick response. I have you covered!

Keep 'em coming, folks!!

Dale53

[2 dogs]

Best put me in for TWO.

fcgarza 0640 AT hot mail DOT com

[Dale53]

2 dogs;
You are on the list. Welcome aboard!

Twenty-seven moulds and counting...

Dale53

[bushwaker]

please put me down for 1 mold thanks.

[Fugowii]

Hi Dale,

What size is this intended to be? I might have a problem as I need a .434" for my SBHH.

Regards,

F

[Dale53]

Bushwaker, you are on the list. Welcome to the "Buy"...

Fugowii,
These moulds are spec'd at .432" with WW's. I suggest you send MiHec a Private Message and ask if he can cut yours at .434" (as I understand it, he may be able to make small corrections). I would do this as soon as possible.

Dale53

[Fugowii]

Fugowii,
These moulds are spec'd at .432" with WW's. I suggest you send MiHec a Private Message and ask if he can cut yours at .434" (as I understand it, he may be able to make small corrections). I would do this as soon as possible.

Dale53

I contacted him through his web site a moment ago. I will let you know what his response is.

Thanks very much,

F

[lonewelder]

I want one
lonewelder at msn dot com

[Dale53]

lonewelder;
You are on the list! Welcome aboard!! Happy to have you join our little group.

Dale53

[Wots]

Newbie question.

I have an .44 S&W 629 with a 6.5” barrel.
I have yet to slug the barrel.
I would think that all of these guns would all have standard barrel’s.
Would this .432 dia. boolet be the one for this gun?

Which handles work for this mold?

Thanks

[Dale53]

Wots;
I have several S&W .44's (both Special and magnums). A bullet sized to .430" works perfectly well in all of my Smiths. I have no reason to doubt that yours should be similar. My Ruger Super Black Hawk, Ruger Red Hawk, and Ruger .44 Lipsey Special all respond well to .430" bullets from these moulds.

We had these moulds spec'd for .432" bullets so that anything from .429"-.432" cylinder throats could be accommodated by sizing accordingly.

Mihec offers premium handles for these moulds and Lee's handles for the Lee six cavity moulds also work well.

http://www.mp-molds.com/shopping/pgm-more_information.php?id=6&=SID

By the way, the critical dimension is NOT the barrel but the cylinder throat. You want the bullet sized to "just" be able to push through the throat with something like a pencil. If it falls through, then it is too small. If you can't push it through the throat with a pencil, then it is too large.

Dale53

[Wots]

Dale
Thanks!
Put me down for one.

WotsamtrU at aol dot com


And the education continues.

[Dale53]

Wots and DGV;
I have you BOTH down for a mould. Truly happy to have you join us!

Don't be bashful, folks! Jump on the band wagon. Be the first in your neighborhood with a MiHec BRASS four cavity mould!![smilie=w:

Dale53

[JDUBS]

if there is room, im in for one! jessdog19 at hotmail dot com let me know, im new to this forum but I have good feedback on another site for transactions if you need a reference :)

Jess

[Dale53]

JDUBS;
You are on the list! Welcome aboard.

The way this works, when the Group Buy closes (six weeks after it started) MiHec will notify you by Email where to send the money (by PayPal). As soon as PayPal notifies him of receipt of the money, the next business day the mould will be in the mail. Delivery can take anywhere from one week to three weeks to get here from Slovenia (Eastern Europe).

Keep 'em coming, folks! Thirty three and counting...

Dale53

[chprplt]

Dale 53
I think this GB is going to be a monster. Miha best lay in a bunch of material for this one. Just out of curiosity, what was the final count of sales for the 45-270SAA 4 cavity mould?

[Dale53]

chprplt;
The list shows 61 moulds ordered. However, there were two or three added after I sent the list in (not counting over runs sold). My best recollection is 64 moulds.

This one is surprising me. I thought "maybe" 25 moulds. Well, we are at thirty three and we are just barely started...it's all your fault, chprplt!:mrgreen:

Dale53

[2003viper]

i will take 1.

[ph4570]

YIKES -- another one I must have. Put me down for one.

videodog at comcast dot net

[Dale53]

2003viper,
We have you on the list - HOWEVER, we need your Email address (camouflage it like everyone else has done).

ph4570;
We have you on the list, also.

Welcome aboard, good people!

Thirty-five and still counting...

Dale53

[Gavetta]

Put me on the list for one. Let me know when you want the money for the four cavity bronze 44 special bullet mold. I'll e-mail you my address.

Gavetta

[AnthonyB]

Dale:
Put me down for one.
anthonybennett __ comcast ___ net
Tony

[Salmon-boy]

Dale:
Thanks for the clarification.. I'm in for one...

salmon-boy using comcast for net

[Dale53]

AnthonyB;
You are on the list! Glad to have you with us!!

Thirty seven and counting...

Dale53

[Dale53]

Salmon-Boy;

>>>Thanks for the clarification.. I'm in for one...<<<

Always happy to help out!
You are on the list! We are happy to see you here, too!

Thirty-Eight and counting!

Dale53

[Von Dingo]

Honestly Dale, you gotta be getting your molds for free from him?

Merry Christmas to me, I'm in for one.

marc Underscore montpetit at hot mail dot com

[Bodydoc447]

Forum name BodyDoc447

email bodydoc447 at aol dot com

Thanks for running this one again. My Ruger Lipsey .44 Special is a dandy shooter and needs one of these moulds as a reward!

Doc

[Ramslammer]

G'Day Dale
When do you reckon Mihec will run this as I have 3 45/70 molds on order from him. I don't want to have too much backed up.
Juddy
ps; The hollow point is a ripper thanks

[Dale53]

Von Dingo;
You are on the list! My motivation is simple. I want this mould and I can't afford to pay for tooling for a one off mould. When I convince all of you people to join me, I am home free![smilie=w: Just think of me like you would your friendly local used car dealer!:shock:

BodyDoc447;
You are on the list! I, too, have a .44 Lipsey Special and there is NO better bullet in that gun than this design. Mine will do under 1" at 25 yards on demand. That is all I ask of any of my revolvers. Further, I have taken a number of deer with this same design and IT WORKS!

Couple that design with MiHecs "Wonder Moulds", what can I say?

Don't hesitate folks, time is winding down.

Forty moulds and counting...

Dale53

[Dale53]

Ramslammer;
This Group Buy runs six weeks from the first post (we are not yet past the first week). I would expect Miha to run this within two weeks (subject to his schedule, of course) of the close of the buy.

I am looking forward to this one, again, myself. I just flat LOVE these moulds.

Dale53

[Ramslammer]

G'Day Dale
Just to make sure they will feed OK, is the crimp groove to nose the same as the hollow point?? Need to make sure before commiting.
thanks
Juddy

[Clyde]

Okay - you got me too, I want one mould.

cpeer at charter.net

[Dale53]

Ramslammer;
This mould is made with the exact same tooling as the original six cavity aluminum mould and the two cavity Cramer style hollow point mould.

Clyde,
You are on the list - happy to have you with us!

Dale53

[atom73]

I am in for one.
atom73atyahoodotcom
Mike Hawley

[Dale53]

Mike;
You are now on the list! Welcome aboard!

Come on, folks! Don't be bashful!

Forty-two and counting...

Dale53

[RP]

Think of these molds as a investment like buying a painting. I think the price of them will just go up over time, As far as I know nobody is making brass moulds of this quality for this price how can you go wrong.

[captaint]

Dale - You got me again.....That's not true. I got myself again. Didn't exactly have to read this thread, did I. Sounds too good to pass up. Gotta have one. Thanks again. Mike
roctober5th@gmail.com

[newrugersafan]

Dale

Please add me to your list for 1 mould, I'm going to get into casting and this looks like a good one to start with.

Thank You
Mike

stobbmataoldotcom

[Dale53]

captaint and newrugersafan;
You are both added to the list. Welcome to our Group!

Keep 'em coming, folks! Don't be shy!

Forty-four moulds and counting...

Dale53

[Jeff_WNY]

Jeff_WNY - castboolits AT lockport DOT net TWO MOULDS

Thank you
Jeff

[Dale53]

Jeff;
Happy to have you with us!

I notice we are seeing some new faces on this buy. That is GOOD! Nothin' quite like "spreading the joy"!!!:drinks:

Forty-Six moulds and counting...

Dale53

[Zeus]

Wow! this one is going to be an impressive turnout :)

[SteveP]

Dale,

I'll take one mold.

SteveP - sjjp at windstream dot net

[EDK]

Hey Dale, I cast a three pound coffee can (standard unit of measure for boolits?) of these using the six cavity aluminum mould today. I think I'd like the brass one even better.

One for EDK....ed dot kayser at yahoo dot com.

:Fire::cbpour::redneck:

[Dale53]

SteveP and EDK - you are both on the list!! Welcome to the buy, my friends!

Forty-eight moulds, and counting...

Dale53

[c.r.]

Please include me for one mold.

carroll.r.adams at gmail dot com

thank you,
c.r.

[ddeaton]

Dale, better put me in for 1

[joeb4065]

I too am the proud owner of one Miha mold, count me in for one please dale. Will the price per drop a bit if we get a big bunch?

[Dale53]

ddeaton - You are on the list. Welcome to the party, buddy! I need your email
address.

joeb4065 - You are also on the list. I need your Email address, also.
Glad to have you with us!
The price will remain the same (we are already getting
a heck of a deal, as it is)!

Fifty-one moulds and counting...:drinks:

Dale53

[cast-n-blast]

Hey Dale ! Can you change my Email to jeffrey dot hoover at montgomerycountymd dot gov Thanks ! I'm #7 on the list.

[Dale53]

cast-n-blast;
Your Email has been changed!

Fifty-one moulds, and counting... Not bad for one week[smilie=w:. Five weeks to go...

Dale53

[ddeaton]

ddeaton at zoomtown dot com

[CBH]

I'll take one, thank you very much.

cwhite86-earthlink-net

[Swindler1]

Please add me to the list for one. Thank you.[smilie=w:[smilie=w:[smilie=w:
dandbohio at aol dotcom

[RedHawk357Mag]

Please add me to the list. RedHawk357Mag at Gmail dot com Thank you

[Dale53]

CBH, Swindler1, and Red Hawk357Mag, you three have been added to the list.

Welcome to the Group! We're happy to have you!:drinks:

Fifty-four moulds and counting...

Dale53

[Doc Highwall]

I would like one Thank You!

[Dale53]

Doc Highwall;
We have you one the list! Welcome aboard!!

However, we need your Email address.

Bushwaker - we still don't have your Email address

Viper 2003 - we still don't have YOUR Email address.

Joeb4065 - we still don't have your Email address, either.

Folks, we MUST have your Email address so we can notify you individually when your mould is finished along with your payment instructions. No Email address, no mould... Please camouflage your email address to confuse spammers.

Fifty-five moulds and counting...:drinks:

Dale53

[Muckman]

Please add me to the list for one mould. Thanks!

pete.connie at live.com

[Doc Highwall]

Doc Highwall, highwall at cox dot net

[Dale53]

Muckman, you are on the list! Glad to have you with us!

Doc Highwall, thanks for the quick response.

NOTE: I have been "talking" to MiHec. He states that he can cut the moulds "large" for those that need a bigger diameter bullet. Standard size is .432" and that is what will be shipped if nothing is said. If you need LARGER, you need to write MiHec a Private Message and request .434" diameter. You need to do that as soon as possible so THAT size will be run for those few who need larger.

Standard size diameter will be .432" as cast with WheelWeights. If you need larger, send a PM to MiHec, immediately.

Fifty-Six moulds and counting...

Dale53

[WMB30]

New face here...Put me in for one. Thanks
wmb30atatt.net

Bill

[Dale53]

WMB30;
You are on the list! Glad to have you here!

Don't be bashful, folks! Get your BEST QUALITY mould, ever, right here!:mrgreen:

Fifty-seven moulds and counting...

Dale53

[fivegunner]

Dale Please put me down for one of these!!!!:lovebooli fivegunner at sbcglobal.net. thanks Frank

[Dale53]

fivegunner;
You are on the list. Happy to have you with us!

Fifty-eight moulds, and counting...:drinks:

Dale53

[Fugowii]

Muckman, you are on the list! Glad to have you with us!

Doc Highwall, thanks for the quick response.

NOTE: I have been "talking" to MiHec. He states that he can cut the moulds "large" for those that need a bigger diameter bullet. Standard size is .432" and that is what will be shipped if nothing is said. If you need LARGER, you need to write MiHec a Private Message and request .434" diameter. You need to do that as soon as possible so THAT size will be run for those few who need larger.

Standard size diameter will be .432" as cast with WheelWeights. If you need larger, send a PM to MiHec, immediately.

Fifty-Six moulds and counting...

Dale53

Sent email requesting .434" size. Thanks!

[RP]

Dale your running a great group buy nice first post and second post of the list thanks again for the work. Any ideal how long before this gets going I dont check my email alot and did not want to miss payment time.

[2 dogs]

Ricky, what you dont want to miss is where MiHec gets on here and post a SIGN UP HERE thread......

[DukeInMaine]

If Miha has your email address, he will send you an invoice to that address, requesting (PayPal) payment. That's when you pay. By then, the molds are all made.

I'm on the fence about getting one of these molds. I already have a bunch of 44 caliber molds, and only one lever action to shoot them in. If I had a revolver, it would make sense for me to jump in.

[Dale53]

Ricky P;
Duke has it correct. The buy will be closed six weeks after it started. Then MiHec will work us into his schedule and start making moulds. After they are finished (typically takes a couple of weeks) he will Email each one of us individually with instructions as to how to pay. As soon as the money is transferred, the moulds will ship the next business day.

Yeah, the anticipation has me whining a bit, too:mrgreen:

Thanks for the kind words, fellows and gals.

Dale53

[Bob J]

Dale, can this be ordered without gas check?

[Dale53]

Bob J;
This bullet mould is for a plain base bullet, only (see the illustration in the opening paragraph).

For what it's worth, I have fired tens of thousands of this style of bullets over the years in both .44 Magnums at full velocity and .44 Specials at more sedate velocities and have never found the need for a gas check. I have had excellent results on both targets and live game.

Dale53

[bushwaker]

my email sprayman2007 at comporium dot net

[Dale53]

bushwaker;
We have your address posted.

I don't know what has happened. We have gone a whole day without someone signing up. Don't be bashful, folks. Step right up and put you name on the dotted line:mrgreen:

Fifty-eight moulds and still counting![smilie=w:

Dale53

[Alex]

Dale,
Count me in for one, again.

alexdoug at sbcglobal dot net

Thanks for Honchoing this one.

[Dale53]

Alex;
You are on the list. We are happy to have you with us!

>>>Thanks for Honchoing this one. <<<

Happy to help out.

Don't be bashful, folks. Don't be left with tears in your eyes because you didn't sign up. Sign up now!

Fifty-nine moulds and counting...

Dale53

[Iowa Fox]

Dale,

Put me down for one.

Thanks for running this one.

slvfx50 at aol dot com

[Dale53]

Iowa Fox;
You are on the list, also! Happy to have you with us!

Sixty-moulds and counting...:bigsmyl2:

Dale53

[Bob J]

Perfect! Count me in for one..... Bob dot Johnson at Invensys dot com


Bob J;
This bullet mould is for a plain base bullet, only (see the illustration in the opening paragraph).

For what it's worth, I have fired tens of thousands of this style of bullets over the years in both .44 Magnums at full velocity and .44 Specials at more sedate velocities and have never found the need for a gas check. I have had excellent results on both targets and live game.

Dale53

[Dale53]

Bob J;
You are on the list. Glad to have you!

Sixty-one moulds and counting...:drinks:

Dale53

[wdr2]

Dale - Please put me down for one mold. The 45 mold Miha made last month is a joy to use. I must have the 44 as well.

wrichins at gmail dot com

[Dale53]

wdr2;
You are on the list! Welcome to the Group!

Sixty-two moulds and counting...I find it hard to believe how fast this one is filling up, but I LOVE IT![smilie=w:

Dale53

[Rodfac]

Dale...Just got off the phone with you....sign me up for this buy, one mold please......Rodfac, aka: Dave Oberg

[Dale53]

Rodfac;
VERY happy to have you join us! We will need your Email address so MiHec can notify you when the moulds are ready.

Sixty-three moulds and counting...

Dale53

[Rodfac]

Sorry Dale...go ahead and use my usual email addy...I don't know how to camo it. Dave (dlober........bell.net)

[Dale53]

Rodfac;
Got you handled! You're going to LOVE this mould!

Dale53

[manomet]

In for one please lebconstruction at gmail dot com

[Dale53]

manomet;
You are on the list! Welcome to the Group. We are happy to have you with us!

Sixty-four moulds and counting...:drinks:

Dale53

[nueces44]

Dale,
Add me to list for 1 mold.
Thanks

[Dale53]

nueces44;
I have added you to the list. Happy to have you with us!

However, I need your Email address. Please camouflage it like the others have.

Sixty-five moulds and counting...[smilie=w:

Dale53

[nueces44]

nueces44 electronic mail is r7277c at yahoo dot com

[Dale53]

nueces44;
Thanks for the quick reply.

My goodness! It has been nearly a whole day without someone signing up.

Don't hold back, folks! Step right up and sign the "dotted line":bigsmyl2:

Sixty-five moulds and counting...

Dale53

[DukeInMaine]

Christ on a crutch!

Ok, ok, ok.... you have worn me down...............

If I don't get this mold, it would be worse than breaking a mirror...........

paypal .... atta .... sebagosales..... dotta ..... com... unications......

[Dale53]

Duke;
You are on the list! Boy, I was really sweating it! A whole day without a sign up would spoil my Guinness Book of Records:veryconfu:veryconfu

Thanks again!:bigsmyl2:

Sixty-Six moulds and counting...

Dale53

[cbrick]

This group buy is the reason I try to not spend a lot of time in the group buy section, yet another mold that I simply cannot live without.

I bought 2 of the 45 270 SAA brass 4 cavs in the GB run by Dale. It was the first GB I got in on and I did so because of the exceptional way it was run by Dale. Tough to express how much I appreciate what has to be a lot of work and a lot of time to run one of these this well.

The two molds from Miha are without doubt the finest molds I have ever cast with. I have about 60 molds and many are excellent but none come even close to Miha's craftsmanship. I have 4 cav molds that have more variation between cavities than does 2 Miha 4 cav molds across 8 cavities. That is craftsmanship in the extreme.

Ok Dale ya got me, put me down for one mold.

Rick at lasc dot us

If I didn't already have 44's I would be out shopping today for one just so I could use another Miha brass 4 cav.

Rick

[cbrick]

Dale,

I just checked the beginning of this thread. It took nine hours to get the minimum order of 15 molds. :coffeecom

You slipping or what? :mrgreen:

Rick

[Dale53]

Cbrick;
Thanks for the kind words, my friend. You are on the list! Your enthusiasm for these moulds mirrors my own feelings.

The rapid sign up for these moulds even surprised me. Since a good number of the present signers already have a fine Mihec six cavity aluminum mould for this exact same design, I was surprised that so many signed up for the four cavity brass moulds. Apparently, quite a number of people feel the same as we do about the precision quality of these moulds. At any rate, I am walking around with a smile on my face (as I suspect Miha is also:mrgreen:). It is a good feeling to know that a LOT of us appreciate excellence...

Sixty-Seven moulds and counting...

Dale53

[chuckbuster]

I would like to get on the list. What do you need from me, I'm new at this part of the game.
Thanx
Kevin
chuckbuster at .com

[cbrick]

I would like to get on the list. What do you need from me, Kevin

chuckbuster at ?.com

That's it Kevin, Dale will add your name & email to the list on page 1 of this thread & your included . . . except your email address looks incomplete. Dale will scold you for that. [smilie=l: The email is needed so that Miha can notify you once the group buy is over and the molds are completed. The email will also be the bill and at that time you pay Miha directly.

Hope this helps,

Rick

[Dale53]

Chuckbuster;
You are on the list. Cbrick is correct. Please check your Email address - it appears to be incomplete.

Happy to have you with us!

Sixty-eight moulds and counting...

Dale53 (still reporting from Utah on a borrowed computer)

[chuckbuster]

Sorry, it was late

chuckbuster @ Hotmail dot com

[Doby45]

WOW, now if we can get this kind of response on the H&G #68 brass 4 cavity mold. ;)

[swiss 96/11]

OK, I am in for one bigrockfish7 at aol dot com Thanks

[Alex]

Dale,
Is it too late to change my order from .432 to .434? I can live with the .432 if I have to.

Thanks,

[yobohadi]

Sign me up for one mold.

mhickok at gmail dot com

[Dale53]

chuckbuster - we have it corrected. Thanks for the quick response.

Alex - just send MiHec a Private Message. Tell him what mould you are signed up for and request the larger bullet. Best do it as soon as possible.

Swiss 96/11 - Welcome to the bunch! We are happy to have you with us! You are on the list!

Beerloaf - Welcome to you, too! We welcome you with open arms! You are on the list!

Doby45 - Is someone running a four cavity brass Group Buy?

Seventy moulds and counting...[smilie=w:

dale53

[Doby45]

Dale I am checking to see if there is enough interest, which I am sure there is. We dang near have enough already for a 15 minimum and more ready to commit once we get the AOK from Miha... I just KNOW you want one. ;)

[Dale53]

bearloaf;
I have your "name" corrected. Thanks for bringing it to my attention.

Doby45;
I would find it hard to say no.

Seventy moulds and counting...

Dale53

[Doby45]

I know you would. ;) I got a PM in to Miha so hopefully we get confirmation on price and schedule and so forth soon.

[jblee10]

Is it too late to get in on this? I'd like one mold .432
jblee10 at hotmail dot com

[Dale53]

jblee10;
You are on the list! Glad to have you!!

Good people. Sign up while you can - DON'T BE BASHFUL!!

Seventy-one moulds and counting...

Dale53

[jblee10]

Thanks Dale! This group buy is a first for me. Looking forward to it, Jim

[cbrick]

Tomorrow is three weeks into a 6 week group buy and we have 71 molds ordered. Three weeks to go, can we get another 29 molds to make it an even 100? How about 44 more to make it 100 over the 15 minimum?

4,345 views of this page in three weeks as of right now, how many of those viewers have a 44 and cast? That's a whole lotta folks kickin themselves in the hieny for passing up a mold of this quality at this price. Compare this to a $170.00 4 cav SAECO iron mold of "ify" quality and an "ify" warranty. Or $75 for a decent RCBS iron 2 cav.

At $85 for a 4 cav Miha brass mold you'll feel like you stole it.

Three weeks to go or this could be you . . . :killingpc

Rick

[Dale53]

cbrick;
You have hit the "nail on the head"!

Don't be bashful, folks. Order up and join those with perpetual grins on their faces!!

Seventy-one moulds, and counting...[smilie=w:

Dale53

[RP]

Hey Dale 53 100 more post and you get another boolit lol.

[cbrick]

Hey Dale 53 100 more post and you get another boolit lol.

One more gold boolit for Dale, just about one more group buy . . . Say for the RCBS 35 Caliber 180 Gr Silhouette boolit in a Miha 4 cav brass mold? [smilie=1: Yep, that should do it!

This is an outstanding 35 caliber long range revolver boolit and to have it in a Miha 4 cav brass mold, well . . .
http://www.lasc.us/TSO_avatar_31657.gif http://www.lasc.us/yupi3ti.gif http://www.lasc.us/thumbsup.gif http://www.lasc.us/z7shysterical.gif

Rick

[Dale53]

CBrick;
I am NOT listening! I am not listening! I am NOT! NOT!:roll::roll::roll:

Dale53

[Dale53]

Fivegunner;
I have made the Email correction. Thanks for bringing that to my attention!

NOTE: To ALL - please check your Email address and screen name to be sure that they are correct. We do NOT want anyone left out because of an error.

Dale53

[farky]

Please put me in for ( one mold )
fishhawk21(at)hotmail(dot)com

farky

[oscarflytyer]

OK - sign me up. Missed the 6 cav alum. Now have 2 44's and need to feed them.

email - myerssw at knology dot net

[Dale53]

farky;
You are on the list!!

oscarflytyer;
You are ALSO on the list!

We are happy to have you both join us in the "sacred" quest!!:bigsmyl2:

Seventy-four moulds and counting...:drinks:

Dale53

[oscarflytyer]

THAT was QUICK!!!

Thanx Dale

[Daddyfixit]

OK Dale, This is an offical addiction. I need another fix man. I also got in on the HG68 moments ago! If the Feds call I won't rat you out as a pusher for my "brass" addiction:veryconfu
I've lost count! Love his work!
Thanks Dale
icmacfamily At hOt MaIL Dott cOm

[Dale53]

Daddyfixit;
You are on the list!! You represent the 75th mould ordered on this Group Buy! That is TERRIFIC!

SEVENTY-FIVE MOULDS AND COUNTING!![smilie=w:

This has my propeller SPINNING!

I guess we might as well pull out all stops and go for 100 moulds. What say you, good people, are you game??:bigsmyl2:

Dale53

[Dale53]

Shortbbl;
You are on the list! Happy to have you join us!

SEVENTY-SIX MOULDS AND COUNTING!![smilie=w:

Dale53

[captaint]

Dale,
We need to change my data on the list - # 39. It's actually captaint, without the cap T. And my email address should not be underlined. My mistake, I'm sure. SO - captaint, roctober5th@gmail.com. One mold, please. And thanks for doing this buy. enjoy Mike

[Dale53]

captaint;
Corrections to the list made!!

I'm happy to work with all of you good people!

Don't hesitate, folks, just step right up here and sign up for the best moulds available!!

Seventy-Six moulds and counting...:drinks:

Dale53

[kirb]

sign me up kdkirby at icsofidaho dot com I know the closing date of this buy what is the time frame to be completed.

Kirb

[Dale53]

kirb;
Happy to have you join us!! You're going to LOVE this mould.

MiHec is aware of the closing date. I expect him to start working on the moulds within two weeks of the closing date. When the moulds are ready (I would guess within two weeks after starting) he will notify us individually how to pay. When money is transferred (typically PayPal) he will send the mould by the next business day. It takes from one to three weeks to hit your door.

Seventy-Seven moulds and counting...[smilie=w:

Dale53

[LAH]

I want two..............Creeker

lah at suddenlink dot net

[johnvid]

Please add me to the list.
jvidmar at roadrunner dot com

[Dale53]

Creeker and John;

I have you both on the list. Happy to have you with us!

Now, you fellers and gals that have been hanging back, just step forward and sign up. With your help, we can make this THE BIG BUY!!:drinks:

Eighty moulds and counting...[smilie=w:

Dale53

[29yrsreload]

Dale53,
Please sign me up for (1) of these. Thanks!!

apalsmei at pixius dot net

[Ramslammer]

G'Day Dale
Got me sucked in again!!! Seriously folks these molds are excellent I've had 4 delivered and have another 3 on order. After this post it'll be 4!!! If I could find a Marlin 1894fg I'd also have to order Mihec molds for that. Anyway Dale put me down for a mold as it'll be a good companion for the hollow point.
namovlov at bigpond dot com
Juddy

[Dale53]

29yearsreload and Ramslammer;
I have you both on the list!! Welcome to our Group Buy and our hearty hello to South Central Kansas and Tasmania, Australia!!

Eighty-two moulds and counting...[smilie=w:

Dale53

[101VooDoo]

Dale,

Please add me to the list for one of these - 101voodoo at sbcglobal dot net.

Jim

[Dale53]

101VooDoo;
You are on the list! Happy to have you aboard!

Eighty-three moulds and counting...:drinks:

Dale53

[wired54]

Please put me down for one.

wired54 at gmail dot com

Thanks

[sljacob]

Im in.. one mold please

sljacob at allwest dot net

[Dale53]

wired54 and sljacob:
I have both of you good people on the list!! Welcome to our Group! I am glad to have you!

Eighty-five moulds and counting... (and heading towards 100:bigsmyl2:)

Dale53

[sljacob]

thanks dale......can't seem to get enough of these fine brass molds:-P

[Shakey Jakey]

I'll have one of these also. putzie at aol dot com

[Dale53]

ShakeyJakey;
We have you on the list!! Happy to have you with us!

Eighty-Six moulds and counting... heading towards 100[smilie=w:

Dale53

[Hickory]

What handles fit this mould?
When will Mihec start producing these moulds?

[Matt_G]

Hickory,

Miha makes handles as well. Real nice ones from what I've heard but he doesn't have any in stock right now.
Lee 6 cavity handles work just fine.
As for your second question Dale would be the one to answer that but my guess would be about 4 to 5 weeks from now.

[Dale53]

Hickory;
See post #174 for projected delivery time.

The Lee handles work well and I have two sets of the Mihec handles and they are indeed premium handles.

Eighty-Six moulds and counting....heading for 100!!

Don't be bashful, folks. I haven't signed up anyone for HOURS! Don't wait until the last minute, folks. Get on the list NOW!!:drinks:

Dale53

[cbrick]

Don't be bashful, folks. I haven't signed up anyone for HOURS! Don't wait until the last minute, folks. Get on the list NOW!!:drinks: Dale53
In a way Dale, you could consider yourself lucky. If all of the people that have viewed this thread really knew the craftsmanship and quality of these molds for the price you would have to hire a secretary to get them all signed up. :holysheep
Rick

[Dale53]

cbrick;
You're probably correct! I love to see the look in people's eyes when they first see these. They just LIGHT up!

Dale53

[DukeInMaine]

I already have a BUNCH of the brass molds, and every time I open up the package on a new one, I shake my head, and smile, and say...... "WOW!"

:D :wow

[Johnny_Cyclone]

I'll jump in for one.

robertditsimonatcoxditnet

[Dale53]

Johnny Cyclone;
You are in for one! Happy to have you join us!!

Duke;
I feel the same way you do!

Eighty-Seven moulds and counting ... heading for 100[smilie=w:

Dale53

[CPTI]

I'm in for one mold.

michael dot iannuccilli @ hotmail dot com

[Dale53]

CPTI;
I have you on the list complete with your Email address. Welcome to the BUY! We are MOST happy to have you join us.

Keep 'em coming folks! I really would like to see this buy hit !00!

Eighty-Eight moulds and counting...heading for 100!:drinks:

Dale53

[Cadillo]

CPTI;
I have you on the list complete with your Email address. Welcome to the BUY! We are MOST happy to have you join us.

Keep 'em coming folks! I really would like to see this buy hit !00!

Eighty-Eight moulds and counting...heading for 100!:drinks:

Dale53

Dale,

If you are logged on, please check your PM's.

[Cadillo]

Dale,

Please sign me up for one mould.

cadillo2 at att dot net

[Dale53]

Cadillo;
You are on the list! Happy to have you with us!

This buy is going better than my expectations! Looks like a lot of us are "of a mind":drinks:.

Eighty-Nine moulds and counting...

Dale53

[emj]

Dale,

Please sign me up for one mould.

ejansen2410 at gmail dot com

Thanks,
Ed

[Dale53]

emj;
I have added you to the list!! You represent the 90th mould sold (#84 on the list)[smilie=w:

That's right, Ninety moulds and counting...

Dale

[chboats]

OK I can't stand it, put me on the list
boatmanc at yahoo dot com

[Dale53]

chboats;
I have you on the list! Welcome! We are SO happy that all of you good folks are joining us!

Ninety-one moulds and counting...[smilie=w:

Dale53

[zac0419]

O.K., let's make it 92. I'm one of those poor souls that knows he'll own a 44 special someday.

I'll take one.

zac0419 at msn dot com

[Hickory]

Dale;
This maybe the best group buy ever.

[Daddyfixit]

Wow! between this one and his HG68 run he is going to be BUSY!
I wouldn't think one guy could pump all these out in an 8 hour shift!

[cbrick]

Wow! between this one and his HG68 run he is going to be BUSY! I wouldn't think one guy could pump all these out in an 8 hour shift!

I have no doubt it is a very large number of 8 hour shifts.

Hickory, you NEED one of these too!

Rick

[Dale53]

zac0419:
This was a very nice "present" for my homecoming. We just got back from SLC, Utah, and I see that you have made it 92!! Glad to have you join us!

Hickory, if you can swing it, you really ought to jump on board!:mrgreen:

Ninety-Two moulds and counting...[smilie=w: Heading for ONE HUNDRED!

I don't know if this is going to be the BIGGEST buy, yet, but it surely is a GOOD ONE!

Each and everyone of you who signed up is partially responsible for this great buy. Look in the mirror and SMILE!! It won't be long...

Dale53

[Hickory]

zac0419:


Hickory, if you can swing it, you really ought to jump on board!:mrgreen:

Ninety-Two moulds and counting...[smilie=w: Heading for ONE HUNDRED!

I don't know if this is going to be the BIGGEST buy, yet, but it surely is a GOOD ONE!



Dale53

A great guy here on this site (Blammer) is buying the mould for me through P-pal.
For that very kind and generous offer I needed only to send him the money.
So, I am on board by proxie.
Thanks again Blammer!!

[Dale53]

Hickory;
That is TERRIFIC!! We are VERY happy to have you aboard!!

Ninety-Two moulds and counting...

Dale53

[LAH]

Dry Creek Bullet Works sold more 44-250-K than any other bullet. As you can see from this thread the 44 isn't as dead as some 45 guys say. HEE HEE

[Dale53]

LAH;
I was shooting my .44 Lipsey Special today with these same bullets (H&G #503 from a MiHec mould). It was SATISFYING to say the least!

I run the same bullet in my .44 Magnums as well as my .44 Specials. It is a "SPECIAL" bullet in both calibers, in my carefully considered opinion.

Dale53

[pack3480]

Two molds for: pack3480
email: dcasad at hotmail dot com

[Dale53]

pack3480:
NOW we are cooking! I have you on the list!

Ninety-Four moulds and counting...heading for ONE HUNDRED!![smilie=w:

Only six more needed to hit that "magic" number. Come on folks, do NOT be bashful!!

Dale53

[Calehedron]

Put me in for 1. kenneth dot ferry at gmail dot com

[Dale53]

Calehedron;
You are on the list!! Again, we are most happy for your presence!

Ninety-Five moulds and counting...heading towards ONE HUNDRED!!:drinks:

Man! I LOVE it!!

Dale53

[LAH]

Looking GOOD.

[Daddyfixit]

Dale, With the huge number of orders ( YAHOOO!) do you have an idea of when these might be shipping? Just wondering. No big rush as I already have a 2 cav RCBS KT-250 & a 3 cav 250 kt Cramer.......So why did I need this one again? Like I said, I'm addicted to those brass beauties!

[cbrick]

I want two..............Creeker

Hey Lynn, I don't know if this will be your first Miha mold but if it is I can assure you that you will be completely amazed. As DukeInMaine said with the WOW factor, for me it was more . . . Oh my, I can't pour lead into this.

I bought 2 of the 45 270 Gr SAA brass 4 cavs and cannot tell the difference between bullets cast from either one, that's two molds and 8 cavities. The blocks fit together so well I have to look close to even see a parting line.

With 2 ordered it looks like Dry Creek Bullet Works will soon be selling some mighty fine 44 Keith bullets, lucky customers you have. :mrgreen:

Rick

[practical_man]

Dale,
I'm in for one mold. 1practical [dot] man [at] gmail [dot] com.

Hope this works as well as the Miha aluminum 503 group buy. that's a great mold!

[Dale53]

practical man;
You are on the list! I have thoroughly enjoyed my MiHec Aluminum moulds. If possible, the brass ones are even better (quality is the same - brass is just somewhat more durable, that's all). Of course, brass is prettier, without a doubt, too.

DaddyFixit;
The Group Buy closes November 23, 2010. Mihec will put it into his schedule, then run all of the moulds. When they are boxed and ready, we'll be notified individually, where and how to pay. As soon as the money is received, the moulds go out the next business day. It takes one to three weeks to get here from Slovenia.

Add this up and it looks like we can start looking in our mailboxes in a month or so.:drinks:

Ninety-Six moulds and counting...heading for 100![smilie=w:

Dale53

[Dale53]

I has been nearly 24 yours since I have signed anybody up. Oh-h-h, the SHAME of it[smilie=b:.

We really need to "step it up", a bit. The old time clock is "awindin' down" - just ten days until this buy closes!

Ninety-Six moulds and counting... headin' for 100 moulds.:bigsmyl2:

Dale53

[DukeInMaine]

24 YOURS????

hahaha he's so nervous that he can't find the "H" key!

Somebody please help the po' boy out!

[Dale53]

What "H" key?[smilie=1:

You must admit, it is almost unprecedented that no "takers" in 24 hours...:shock::shock:

Come on, guys and gals, let's "get with it"!!:holysheep

Dale53

[Dale53]

We have had one order reduced.

Ninety-Five moulds, and counting...

Dale53

[fobis01]

Dale
Please put me on list for one mold
csmith3 at vtown dot com dot au

[Blazenet]

Put me down for one
Thanks
Blazenet AT Comcast dot net

[Dale53]

fobis01 and Blazenet;
We have both of you on the list. Most happy to have you aboard!!

Ninety-Seven moulds and counting...heading for ONE HUNDRED
:drinks:
Dale53

[DukeInMaine]

Now, see.... two in one day is gonna get Dale all excited again.................

Things will happen:


He'll forget where his car keys are again
He'll forget where he put his glasses again (they're on top of your head, bud!)
He'll start calculating the average orders per day, for the past week
And, then, he'll factor in the one cancellation.... and whimper about it for about a day....
Whenwe reach 98 molds, he'll start to drool, and we might even need to have some Depends on hand.... just in case.....


Haha... made you laugh!

[Dale53]

Dukein Maine;
You're BAD!!:bigsmyl2:

Dale53

[Mal Paso]

I'm pretty sure I need 1 too.
429421 at gmail dot com

[Dale53]

Mal Paso;
We have you on the list! You are ABSOLUTELY gonna love this one!

Ninety-Eight moulds and counting...ONE HUNDRED, I can TASTE you!:bigsmyl2:

Dale53

[MtMark45]

put me down for 1 mold.
mlkeith 45@ aol.com

[LAH]

Hey Lynn, I don't know if this will be your first Miha mold but if it is I can assure you that you will be completely amazed. As DukeInMaine said with the WOW factor, for me it was more . . . Oh my, I can't pour lead into this.

I bought 2 of the 45 270 Gr SAA brass 4 cavs and cannot tell the difference between bullets cast from either one, that's two molds and 8 cavities. The blocks fit together so well I have to look close to even see a parting line.

With 2 ordered it looks like Dry Creek Bullet Works will soon be selling some mighty fine 44 Keith bullets, lucky customers you have. :mrgreen:

Rick

I purchased one of the 45-270 brass moulds & wish I'd got two. I'll not make the same mistake with the 44. I have two excellent Lyman 429421 moulds with which I cast the DC 44-250-K bullets. This bullet sold more than any we produced & for my use I find no fault but I get people wanting something a little larger than these will cast. I can size a true .430 but a .431 die doesn't touch the bullet everywhere. This shouldn't be the case with these moulds.

If they work & do as I believe they will be the new 44 bullet..............Creeker

[cbrick]

Ninety-Eight moulds and counting...ONE HUNDRED, I can TASTE you! Dale53


put me down for 1 mold. mlkeith 45@ aol.com

Gee Dale, I have been thinking of getting two. [smilie=1:

Rick

[CATS]

Please put me on the list for one mold.
Dale, PM sent. Thanks!
CATS

[Dale53]

MtMark45 and CATS,
I have you both on the list and WE HAVE HIT ONE HUNDRED MOULDS!!

But-t-t-t, we are STILL counting...

cbrick;
If you are serious, I can still "hook you up" with another mould...[smilie=w:

Dale53

[cbrick]

No need now. I was just trying to get your adrenaline pumped up.

But we still need 15 more to make it 100 over the 15 minimum and we have a week and a half, bet we make it.

Rick

[Dale53]

cbrick;
You sir, are an ENABLER!!:kidding::bigsmyl2:

Dale53

[cbrick]

Perhaps but I still bet we make 115. Lot's of people are learning about the quality of these molds, lot's of people have 44's, lot's of people cast.

Heading to 115.

Rick

[Dale53]

Perhaps but I still bet we make 115. Lot's of people are learning about the quality of these molds, lot's of people have 44's, lot's of people cast.

Heading to 115.

Rick

Of course, you are "right on"! And that is a GOOD thing!

Dale53

[foxtrotter]

I'll take one.
foxtrotter at rtci dot net
Dennis

[Dale53]

foxtrotter;
We have you on the list! Welcome to the Buy!

One-Hundred-One moulds and counting....:drinks:

Dale53

[That'll Do]

Add me to the list for one mold, please. I can't resist the temptation any longer!

bron_yr_aur (at) comcast (dot) net

[Dale53]

That'll Do;
You are on the list!! Congratulations - I knew you couldn't resist!:mrgreen:

One-Hundred and TWO moulds and counting...[smilie=w:

Dale53

[eastwa]

Do I have a spending problem if I buy equipment for a caliber I don't own (yet)?
This will be my first "custom" mould, and am looking forward to it.

eastwa78 (AT) msn (DOT) com

eastwa

[Dale53]

Do I have a spending problem if I buy equipment for a caliber I don't own (yet)?


Either that OR, I prefer to think, you have the ability to plan ahead!

You are on the list. If this is your first custom mould, you have a treat in store for you! Welcome to the "Buy"...

One-Hundred-THREE moulds and counting...:drinks:

Dale53

[Mak Rov]

Well, I tried to resist but I can't. MiHec's molds are a work of art.
Put me in for one.
gmctrk at comcast dot net
Thanks,
Ken