View Full Version : Noe 311284
I bought 3 different Lyman 311284 molds. Every blasted one of them cast undersized bullets. The nose on 1 of them miked .2975 ". Useless in my .30 cal. rifles. ( I guess that was Lyman's best attempt at making a decent .30 cal. mold, I'm probably finished buying newly manufactured Lyman molds in any caliber ).
This NOE 311284 from Swede is so close to perfection, words can't express my current satisfaction with this mold. The rejection rate on this mold is near ZERO, all bullets are filled out well, base fills out well. Most of the bullets fall from the mold without a tap on the hinge pin of the handles.
Bands mike a near perfectly round .314 " The nose mikes .3018 "
If you're looking to buy a mold that is right the 1st time, take a good hard look at NOE ! !
Ben
http://img.photobucket.com/albums/v494/haysb/NOE%20311284/PICT0003-1.gif
http://img.photobucket.com/albums/v494/haysb/NOE%20311284/PICT0002.jpg
schoolbus
11-05-2009, 01:47 PM
That sure is a purty boolit, Ben. I hope my NOE 22-055 FN casts that good.
Gordon
JesterGrin_1
11-05-2009, 03:54 PM
They look GREAT. But I have to ask will these work in lets say a Marlin XL-7 in 30-06 or a Rem 700 in 30-06?
When the GB started I was told the nose was a bit too large is this correct?
The nose of .3018 " isn't too large for my 9 different .30 cal. rifles. Works good in all of them.
Ben
Blammer
11-05-2009, 07:26 PM
This boolit will work GREAT in a Rem700 30-06. :)
One of my 100 yd targets with the 311284 and my rem 700
each square is 1/2"
http://i54.photobucket.com/albums/g81/blammer8mm/Targets/311284.jpg
Blammer :
Do you mind sharing that load in the test target above ?
Ben
Blammer
11-05-2009, 08:31 PM
not a problem
WW Super brass
WLR primer
.301 on the nose
sized to .309
31gr of IMR4475 (aka IMR3031) the 4475 was military pull down powder
3 diff types of lube in the sizer
I've got IMR 3031.......I'll give that one a try.
Many Thanks,
Ben
Byron Cromwell
07-03-2010, 01:02 PM
I am happy to see a custom mould maker with a classic design, but the .314 inch driving band is a little too large for me. Can this mould maker produce one that will cast narrower, perhaps to .307 with pure lead, so adding antimony (such as wheelweights or pure antimony ingot I purchased twenty-odd years ago to make my own type metal) will cause it to throw to .309-310 inch? I prefer not to size at all, and have had good success with boolits miking at .001" undersize in rifles. I have moulds which throw oversize and they are more trouble than the ones that throwe under, in my experience, but maybe I am just unlucky.
Thanks
Welcome Byron ! ! !
You'll just have to contact Swede Nelson at NOE, ( go to the Vendor section and PM AL )
Again ........Welcome,
Ben
RugerFan
07-03-2010, 03:22 PM
That GB is running again. Is .312" still too big?
http://castboolits.gunloads.com/showthread.php?t=86382
NuJudge
07-05-2010, 01:32 PM
I bought 3 different Lyman 311284 molds. Every blasted one of them cast undersized bullets. The nose on 1 of them miked .2975 ". Useless in my .30 cal. rifles.
That mold would be perfect for a Swiss K31. You should have no trouble finding a buyer for it around here.
CDD
Byron Cromwell
07-07-2010, 06:04 PM
Ben,
Just looked at your post in reply to mine. Given the time involved, I'd like to try trading my mould for a mould that someone already has and is having "undersize" issues with. Might solve both our problems and would be less expensive, and possibly faster, than going on the custom route. I'm not averse to spending the money and getting it right the first time with a custom job, but if there's some frustrated mould-holder there who's stuck with a paperweight, I would like to trade if I can.
Blammer
07-07-2010, 06:09 PM
Swappin and sellin will be your friend there.
Mark Daiute
03-05-2011, 11:07 AM
not a problem
WW Super brass
WLR primer
.301 on the nose
sized to .309
31gr of IMR4475 (aka IMR3031) the 4475 was military pull down powder
3 diff types of lube in the sizer
alloy?
Water dropped?
Thanks,
Mark
Blammer
03-05-2011, 11:52 PM
WW alloy air cooled.
Pa.guy
02-14-2012, 11:23 PM
Disapointed to hear lyman molds cast undersize 311284 bullets as i just bought one 2/7/12.
Plan on shooting them in a model 54 target 30-06, haven't warmed it up yet. I'll post sizes later.
PaGuy
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.