432-265 RFGC Group Buy is Closed

[SciFiJim]

432-265 GC RF Group Buy is Now Open.


Enough people have expressed an interest in the Ranch Dog #2 Poll (http://castboolits.gunloads.com/showthread.php?t=55533) to run this.

This Group Buy is for a 432-265 Gas Checked Round Flat Nosed boolit that is a lube groove copy of the Ranch Dog TLC 432-265 RF bullet designed for the 44 Magnum rifle and 444 Marlin rifle. The molds will be produced by Night Owl Enterprises (NOE) in their standard 1-5 cavity molds AND the RG Hollow Point molds.

The 432-265RFGC Group Buy will close on November 16th. If we don’t have 15 orders by then, the close date will be extended until we do.

Flat Nosed Boolit

http://castboolits.gunloads.com/picture.php?albumid=170&pictureid=1278


Hollow Pointed Boolit

http://castboolits.gunloads.com/picture.php?albumid=170&pictureid=1279


Moulds will be machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.



The cost will be as follows:

Standard Molds
Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.
Hollow pointing one cavity and furnishing a double ended pin would be $35.00 extra.
If you want to fashion different HP profiles, an extra blank pin would be $1.50

RG Molds
Two cavity RG2 HP mould $96.00 Ea.
Includes one set of hollow point pins
and one set of flat nose pins.
If you want to fashion different HP profiles for the RG2 an extra blank pin set of two (2) would be $4.

Four cavity RG4 HP mould $126.00 Ea.
Includes one set of hollow point pins
and one set of flat nose pins.
If you want to fashion different HP profiles for the RG4 an extra blank pin set of four (4) would be $8.

Shipping and handling will be $10 per order and shipped priority mail. If you live outside the United States contact me, and I will work with you.



Lead time is 4-5 weeks after Group Buy closes. Tooling will be ordered once we get to 15 paid orders so don’t delay.

Instructions for using the Group Buy order system page are HERE (http://castboolits.gunloads.com/showthread.php?t=56550).

Use the Group Buy order system HERE (http://www.groupbuys.dnsalias.com/login.asp) to place your order. Use the link provided or use the link at the bottom of the page. Print two copies of the order sheet and mail both to me with your payment. Once we are ready to go, I will place the order with NOE. The molds will be shipped to me and I will distribute them. I will accept bank check, money order or PayPal + $4.50. If using PayPal contact me first.

We can get gas checked and non gas checked cavities cut in the same mould. Specify on the order sheet what your preference is.

The mold is machined to use LEE Commercial 6-Cavity handles (not included).
A Lyman, RCBS type top punch is furnished with each mould as well as a sample of Bull Plate sprue plate lube.

Visitors from other forums are welcome to participate in this group buy.
Email me at scifijim - at - gmail.com
Do the normal voodoo with the address to make it work, I don't want spambots to skim for my address.

Please leave a post here or PM me when you order and I will add you to the list.

I will post a running list of confirmed orders with username and options and a list of zip codes that payments have been received from in the next post.
Thanks
Jim

[SciFiJim]

Orders
1. GLL - Single cavity w/HP + 3 blank pins
2. phaessler - RG2
3. jojo- 5 cavity (2 gas checked & 3 plain base)
4. Ron.D - 5 cavity
5. runnin lead - 5 cavity (4 plain base)
6. DGV - 3 cavity
7. johnny356ER - 4 cavity
8. 15bobcat - RG2
9. timbuck - RG4 + 2 Blank pin sets
10. 6pt-sika - RG4
11. 7.62Man - 4 cavity
12. Lloyd Smale - RG2
13. happy7 - RG4 (all plain base)
14. insanelupus - 4 cavity
15. adkpete - 4 cavity w/HP (all plain base)
16. SciFiJim - 4 cavity (2 GC & 2 plain base)
17. jfe - RG4 + 1 blank pin set
18. mancuso - RG2 + 2 blank pin sets
19. hicard - RG4 (2 GC & 2 plain base)
20. no34570 - RG2 + 1 blank pin set
21. kfarm - 3 cavity w/HP
22. denul - RG4
23. EDK - 5 cavity (all plain base)
24. HammerMTB - 4 cavity (1 GC & 3 plain base)
25. primersp - 2 cavity
26. PoorGuy - 4 cavity (2 GC & 2 plain base)
27. Tazman1602 - 2 cavity
28. deepsouth - 3 cavity
29. 358wcf - 3 cavity w/HP (all plain base)
30. OBXPilgrim - RG2
31. Duhawki - 3 cavity




Zip Codes of Payments Received
91106
24121
99224
L9S2B6
01085
12586
53132
22960
P7G1M3
12912
48962
72525
59917
3122 Australia
14080
96055
3889 Australia
98233
72206
40741
63012
France
30062
49706
39574
94521
80467
28803
45365
07832

[Ron.D]

Count me in, I've been waiting for this one. 5 cavity. Money order will be in Monday's mail.
Thanks. Ron.D

[GLL]

Jim:

I will order one 1-cavity +HP+3 extra pins !

Will the HP profile be the same as the RF version? I hope so ! :)

Jerry

[phaessler]

Jim:

I'm in, payment will go out tommorrow.

432265 RG2 2 cavity NOE RG mold for 432265 WITH GC

Thank you,

Pete

[timbuck]

Im interested in a RG4 but dont want to tie up the money for more time than I have to. I will get in closer to November.

[JesterGrin_1]

The RD 300Gr would be nice. :)

[SciFiJim]

timbuck - go ahead and place the order. As long as I know that the payment is coming we are good.

[DeepSouth]

Hello folks,question I Missed this somewhere I guess.Then again I've never done a group buy before but what is RG mold compared to the standard mold?

[JesterGrin_1]

Hello folks,question I Missed this somewhere I guess.Then again I've never done a group buy before but what is RG mold compared to the standard mold?

You mean RD as in Ranch Dog. Here you go. http://www.ranchdogmolds.com/TLC432265RF/

[SciFiJim]

The RG type of molds are described here (http://castboolits.gunloads.com/showthread.php?t=56593&page=2). Check out post #22. It's a way of having multiple hollow pointed cavities on an aluminum mold. Sort of like a cramer type by different. The RG stands for Rube Goldberg.:wink:

[DGV]

Does the RD version of this bullet function good in a unmodified 1894 Marlin 44 magnum?

[SciFiJim]

If you are referring to a 444 Marlin, this boolit was designed for it.

[johnny356ER]

Jim.
I would like to order the standard 4 cavity all gas checked...This is my first group buy, and when I go to create a login, I fill in all my info I keep getting an error...all fields are filled in.
I can't figure out anything I'm doing wrong...
johnny

[SciFiJim]

If you have created a login and are still having difficulty, please pm wiljen or felix for assistance.

The above is a quote from the Group Buy Order page. Either wiljen or felix can help you with the log in process. Please try them first. They have greater access to that page and can fix what needs fixing. In your PM to one of them you might copy and paste the error message.

[JesterGrin_1]

Yes the RD432-265GR is for the .44 Marlin and the .444 Marlin. They also work good in .44 Mag Revolvers. :).

[JesterGrin_1]

The RG type of molds are described here (http://castboolits.gunloads.com/showthread.php?t=56593&page=2). Check out post #22. It's a way of having multiple hollow pointed cavities on an aluminum mold. Sort of like a cramer type by different. The RG stands for Rube Goldberg.:wink:

Thank You Jimbo. I missed that part lol. Since the thread was about the RD I thought he just put it down wrong as RG lol.

Thank You for the correction. :bigsmyl2:

[DGV]

I am in for a 3 cavity 432265 GC. Will send a MO next week.

[runnin lead]

I kept getting an error message ,was puzzled , kept getting same message , went & tried to log in & did log in .

[johnny356ER]

Ok.. I got it right this time by doing nothing different!!
Just ordered a 4 cavity 432-265 GC
Printed my receipt(2) and will get my MO out in the mail tomorrow.
Life is Good
johnny

[SciFiJim]

A bunch of new orders today. Thanks guys. Check post #2 to make sure I got it right.

[timbuck]

Just got in for 432265 RG4 with two sets of pins. Will send money Nov. 1 or when gb is closed, or earlier if needed.

It shows shipping as 30$. Is that correct? Will do insurance too.

[6pt-sika]

I want a single cavity gas check hollow point mold !

I had your mailing address but seem to have lost or deleted it !

So shoot me a PM with your snail mail add and I will get a MO in the mail :bigsmyl2:

[Ron.D]

Woo Hoo. less than 4 days and 10 orders in. Smokin. Ron.D

[GLL]

timbuck:

My shipping came to $50.00 for my single cavity HP mould & 3 pins! :) :) The system charges $10.00 for each item you order.

Just subtract $20.00 from your total and all will be fine.

Jerry

[SciFiJim]

Thanks Jerry, I am back at work now and can't normally respond during the day. Yes, shipping is $10 instead of $30.

[7.62Man]

Jim,

I am in will take a four cavity

[6pt-sika]

Explain this "RG" mold thing to me I just noticed it tonight !

[SciFiJim]

6pt-sika - I sent you a PM before I noticed this post.

For everyone that hasn't found out about this "innovation", I sent the following to 6pt-sika.

The RG mold is NOE's answer to a mold hollow pointed in the Cramer style. Normally Cramer HP's are done in steel or brass molds (aluminum is too soft). The RG molds have the hollow point pins attached to the mold blocks with steel "slides" that hold the pin but allow it to move when dropping the boolits. There are some pictures of it HERE (http://castboolits.gunloads.com/showthread.php?t=56593&page=2) in post #22.

[6pt-sika]

6pt-sika - I sent you a PM before I noticed this post.

For everyone that hasn't found out about this "innovation", I sent the following to 6pt-sika.

The RG mold is NOE's answer to a mold hollow pointed in the Cramer style. Normally Cramer HP's are done in steel or brass molds (aluminum is too soft). The RG molds have the hollow point pins attached to the mold blocks with steel "slides" that hold the pin but allow it to move when dropping the boolits. There are some pictures of it HERE (http://castboolits.gunloads.com/showthread.php?t=56593&page=2) in post #22.



Okay change me to a "RG4" please !

[SciFiJim]

6pt-sika - I changed you order.
Jim

[6pt-sika]

6pt-sika - I changed you order.
Jim

Thank you !

[6pt-sika]

Put my MO in the mail a few minutes ago Priority so you should have monday or tuesday I think !

Thanks :drinks:

[no34570]

I was in the Lee GB of this bullet a few years ago(265 or 285???) on Cast Boolits,got the mould and the damn thing was casting undersized,we sent it back twice was not real happy with it,but makes a good pp boolit.

Would like to get another crack at this boolit, use in my 444 & 44 mag Rossi LA,money is tight at the moment,but won't close until November,probably will be going for it.

[EDK]

I've got the RANCH DOG version in two AND six cavity versions. It works like a champ in my unaltered MARLIN 44 magnum Cowboy rifles...and equally well in any of a dozen revolvers I've tried it in. The only problem is that it is a gas check design and I really don't need them in my VAQUEROS/BLACKHAWKS at my comfort level of practice/utility loads.

If I read correctly, I can get this in a plain base or mix...and have until mid November to decide what I want. PLUS maybe I'll get some cash for my birthday next month to help pay for it?

Thanks for this design. I love the 360180 WFN in my 357s and I've been wanting a full wadcutter 45 for a long time (Jim got my check for that one yesterday!) Your crew does excellent work....only improvement would be to trough the sprue plate a la HENSLEY & GIBBS for enhanced production while ladle casting.

Thanks again guys...I'll talk to you with yankee dollars in hand later.

:Fire::cbpour::redneck:

[phaessler]

Just moving it to the top, alot of people look forthe mold after it closes anddont want anyone missing out.

[EDK]

I was in the Lee GB of this bullet a few years ago(265 or 285???) on Cast Boolits,got the mould and the damn thing was casting undersized,we sent it back twice was not real happy with it,but makes a good pp boolit.

Would like to get another crack at this boolit, use in my 444 & 44 mag Rossi LA,money is tight at the moment,but won't close until November,probably will be going for it.

Swede and the guys will get it right. I've got the 360 180; ordered (and paid for!) the 45 full wadcutter; and now got to gather funds for this and the proposed 360 200 semi wadcutter. Only complaints are they don't trough the sprue plate ala H&G...and they keep coming up with moulds that I got to have!

:cbpour::redneck::Fire:

[6pt-sika]

Well it was off and running at a good pace and then it seemed to die out !

We need 4 more folks that committed via the poll to come forward and get the ball rolling to 15 and then this thing can go off as scheduled when the time gets here as opposed to waiting a couple more months :cbpour:

[6pt-sika]

I was in the Lee GB of this bullet a few years ago(265 or 285???) on Cast Boolits,got the mould and the damn thing was casting undersized,we sent it back twice was not real happy with it,but makes a good pp boolit.


I was fortunate with this in the fact that the FIRST design was called the 432-285GC and Ranch Dog let me have one of his four or five original molds . The mold worked well for us , but as you said there were problems with the group buy run by another here .

Later he changed it a bit a renamed it the 432-265GC as actually the earlier mold never made bullets quite to the 285 grain level .

When he came out with the 432-265GC I was again fortunate and able to get one of the original test molds and it worked great . When Ranch Dog got the 6 cavity going I again got one of those and I'm actually ashamed to say I have yet to use the higher capacity mold (already had a pile of the 265's cast up from the 2 banger) .

Anyway the next step in this equation for me is this 4 cavity RG mold . This should be very intresting to say the least in a 444 !

Now that the 432-350GC high capacity and HP molds are on their way in the next 4 or 5 weeks and this mold will hopefully be here by Xmas , perhaps we need to light a fire under the 432-300GC . I'd be in for a 5 banger and a RG4 of that one as well [smilie=s:

[no34570]

Bugger
Looks lie I will have to really think about getting in on this deal.
Hmmmm.....just might you know,it sure is tempting.

[insanelupus]

SciFi Jim,

I put in an order on the group buy page for a 4 cavity mould. Payment was mailed today. Thank you.

[SciFiJim]

Insanelupus,
I will let you know when the payment arrives.
Thanks
Jim

[kbstenberg]

I hope to sign up at the last minute. My wife isn't too happy with the 2 i have an the 3 on the way. She just doesnt understand

[SciFiJim]

I will put out a last call about a week before the close date. I hope you are able to get in on it.

[no34570]

Scifijim

:groner:
Ok,I cannot pass this up.;)
I'm in for an RG2 HP mould with GC & an extra set of blank pins

Mould=$96.00
Paypal fee =$4.50
Extra pins=$4.00
Freight to Australia= ??????
Total there =$104.50US

Can you PM me please Jim with cost to the land of Oz,will pay before GB closes(2 weeks otherwise)is that ok?

Now I have to decide if I want the 432300RFGC :groner:
All these good moulds that are coming on the forum,it's great,but makes you broke:lovebooli

[6pt-sika]

Now I have to decide if I want the 432300RFGC :groner:


There's no decision involved !

You know you want it :bigsmyl2:

You wouldn't even have brought it up unless you already knew deep down you wanted one [smilie=w:

[no34570]

There's no decision involved !

You know you want it :bigsmyl2:

You wouldn't even have brought it up unless you already knew deep down you wanted one [smilie=w:


Can't argue with logic:bigsmyl2:

[hicard]

Put me down for a RG4 cavity 432-265gr rfhp, 2 GC and 2 PB if possible.
Payment sent 10/20/09

[SciFiJim]

hicard - I added you to the list. "2 GC and 2 PB" is easy.
Thanks
Jim

[no34570]

Scifijim
My name is not in the orders for this one too
Should I PM you?

[kfarm]

Jim, I just got to get in on this one too.
Please put me down for a 3 cavity, all Gas Check with one cavity being a HP.
I will get a check in the mail in the next couple of days.

I have misplaced your address so please send me a PM
Thanks Carroll

[ghh3rd]

Hollow pointing one cavity and furnishing a double ended pin would be $35.00 extra
Any idea how many grains the HP cavity would drop at, since it's missing a bit of lead?

Although this boolit seems to be designed for a rifle, any idea how it will do in a Ruger Super Blackhawk .44 revolver?

Thanks,


Randy

[SciFiJim]

The hollow pointed boolit would drop at about 240gr.

It should work well in a RSB, there are a lot of loads listed for this weight and similar profile bullet. With a gas check it could be loaded up or down depending on need.

[ghh3rd]

Thanks, Jim -- by the way, does this boolit require a gas check?

I'd rather not use gas checks unless I really need to. I haven't received my RSB yet, so don't know how much problem I'll have with leading, which I know a gas check helps prevent.

This RSB has me tapped out financially, but I'd sure like to get this mold if I can swing it.

Randy

[6pt-sika]

Thanks, Jim -- by the way, does this boolit require a gas check?


You can specify either flavor !

[SciFiJim]

Thanks, Jim -- by the way, does this boolit require a gas check?

The default is with a gas check. If you wish, you can order any number of the cavities in your mold without a gas check at no extra charge. If you look at the orders in post #2 of this thread, you will see what other people have ordered as an example.

[SciFiJim]

There are only two weeks left until the close date of this group buy. If you haven't send payment yet, please think about sending it soon.
Thanks
Jim

[denul]

PM and payment sent for this and 41 Kieth

[SciFiJim]

denul - I added you to the list.
Thank You
Jim

[timbuck]

The check is in the mail.

[SciFiJim]

TB - Thanks, I will PM you when it gets here.
Jim

[EDK]

I just did the group buy thing for a five cavity BUT I want all plain base. Check will be headed your way as soon as I find a stamp...I got the flu BIG TIME and the mail box on the county road is a major trip right now...haven't had anything like this before.

The RANCH DOG parent of this mould has worked well in my MARLIN Cowboys and assorted RUGERS. Only problem is the gas checks are unnecessary and expensive for my level of reloading. Swede and the boys did a great job on 360 180 WFN and now I'm waiting for the 45 wadcutter and this one.

Thanks again...and keep up the good work

:cbpour::redneck::Fire:

[SciFiJim]

EDK - I added you to the list. Missed a couple of days of work this week because of the flu myself.

[johnny356ER]

Just got back from my elk trip...I already ordered,just need to get out payment today...hope its not too late
johnny

[SciFiJim]

hope its not too late

Nope. Still time!:)

[no34570]

SciFiJim
PM'ed you about my payment,will be this coming Friday,will have no access to computer until then,plus will be paid by Thursday night.ok?

[SciFiJim]

That will be fine.
Thanks

[primersp]

scifijim
please add me to the list for a 2 cav g.c.,paiement by paypal and shipping to france
thanks.

[SciFiJim]

primersp - I added you to the list. PM sent.
Thanks
Jim

[primersp]

thanks jim paiement send

[SciFiJim]

Payment received.
Thank You
Jim

[SciFiJim]

This group buy will be closing on Monday. If you have been kicking the tires on this one, it's time to order. If you haven't sent your payment in yet, please do so this week.
Thanks
Jim

[PoorGuy]

OK then, how about a 4 Cavity with 2 PB and 2 GC. PM Sent...

[SciFiJim]

PoorGuy - I added you to the list. PM returned...

[PoorGuy]

Thanks! Payment sent.

[GLL]

Jim:

Please check your "paid" list for 91106 !

Jerry

[hicard]

Could you also check your "paid" list for 96055 ? Payment was sent on 10/20/09

[SciFiJim]

GLL & hicard, PM's sent. Zip codes are now posted.

[no34570]

SciFijim
Just sent payment to you using paypal

Cheers
no34570

[SciFiJim]

Got it.
Thanks
Jim

[Tazman1602]

Jim,

Just placed and order number 2132 for the 432265 RFGC 2C mold. I emailed and PM'd you about Paypal also. Please make sure I'm on the list.

Many Thanks,

Art

[DeepSouth]

Hey Scifijim,I keep trying to create an acct, so I can oder the mould but it want let me.It keeps telling me (cannot connect to site or PK key violation something about a duplicate key).I would like a three cavity all gas check.Tell me what to do and I'll get it done.

[SciFiJim]

Tazman - I added you to the list. PM'd back.

DeepSouth - I see your order. It looks like you figured it out.:p I added you the the list.

Thanks
Jim

[Tazman1602]

Money and PM sent Jim, thanks for getting back to me so fast.

Art

[DeepSouth]

Scifijim,I'm going to try to do this though paypal if my acct will work.I haven't used paypal in awhile if it want work and I have to pay by one of the other ways.Will I still have time to send payment to you.This is first time to do a group buy just want to make sure everything is right.

[358wcf]

Jim,
Put me down for a 3cav NOE mold, with one HP, all cavities Plain Base, please!
I will take care of the paypal part of this today-

Thanks,

358wcf [smilie=1:[smilie=1:[smilie=1:
Chuck

[SciFiJim]

Tazman - No Problem. I've been doing a lot of this,:coffeecom.

DeepSouth - There is still time. If you have to mail the payment, please send a Postal Money. I can cash those at the post office.

358wcf - I added you to the list.

Thanks everyone,
Jim

[SciFiJim]

This group buy closes tomorrow. I am giving a LAST CALL on this one. Get in while you can. At this point PayPal is preferred, but if you have to mail the payment, please send a Postal money order. I can cash those at the post office.
Thanks Guys,
Jim

[DeepSouth]

Jim i'm trying to pay for this by paypal.Do I need your email address to do this.if so could you pm your e mail address to me.I've only uesd paypal on ebay never to a person. thanks

[OBXPilgrim]

Alright, I've ordered one, an RG2.

Looks like one I can't do without.

[SciFiJim]

DeepSouth - emails exchanged and payment received. Thank You

OBXPilgrim - PM sent

[OBXPilgrim]

PM back to you, thanks for straightening me out.

[SciFiJim]

This group buy is now closed! I am waiting for one more payment to arrive before sending in the order. Thanks everyone that participated.
Jim

[runnin lead]

Jim
Thanks for running this group buy , it was the only mould that I still needed , been wanting a non tumble lube of this bullet for a while when this mould arives I will never ever need to order another mould in my life .
Gee that 460-425 sure looks like a mould that I just may have to get one of.

[SciFiJim]

I only started casting my boolits this year. Molds are like rabbits. I've already got nine molds and more on the way.

[OBXPilgrim]

when this mould arives I will never ever need to order another mould in my life .



I bet you're the only one that's ever felt that way around here.

[runnin lead]

I quit buying guns too, I will never ever buy another gun . My dogs told me it is OK to buy shotguns , they also said if I want to build another muzzleloader a fowling piece would be OK.

[SciFiJim]

The order has been sent to NOE. Now we wait. We should get it in time for some mid-winter casting.:cbpour:

[SciFiJim]

Last payments arrived today.
Thanks Everyone.
Jim

[6pt-sika]

Last payments arrived today.
Thanks Everyone.
Jim

Should we expect to recieve this thing before february ?

[SciFiJim]

According to SwedeNelson's schedule HERE (http://castboolits.gunloads.com/showthread.php?t=68694) it is scheduled to run in the last week of January. So if no problems crop up with any of the other molds scheduled ahead of it, I should receive them in the first week of February. I usually turn them around to remail in a day or two. With 31 molds in the order it might take me a couple of days.

[6pt-sika]

According to SwedeNelson's schedule HERE (http://castboolits.gunloads.com/showthread.php?t=68694) it is scheduled to run in the last week of January. So if no problems crop up with any of the other molds scheduled ahead of it, I should receive them in the first week of February. I usually turn them around to remail in a day or two. With 31 molds in the order it might take me a couple of days.

I was hoping to see it before I left the country !

If it gets to me by 2/6/10 then I will otherwise I'll not see it until 2/28/10 :?

[phaessler]

Based on Swede's schedule.....

http://castboolits.gunloads.com/showthread.php?t=68694


Pete

[phaessler]

(31) 432-265Gr. RF (RD) April now?

http://castboolits.gunloads.com/showthread.php?t=68694&highlight=NOE+schedule&page=2

[SciFiJim]

I will be leaving in the morning to visit the inlaws for a few days. Since they don't feel the need to have internet access I will be out of touch until I get home on New Years eve. I will answer PMs and questions then. My mail is being held at the PO, so any payments sent will be safe. Have a Happy New Year everyone.


[smilie=w: My 1000th post! To say I will be out of touch for a while.:wink:

[6pt-sika]

(31) 432-265Gr. RF (RD) April now?

http://castboolits.gunloads.com/showthread.php?t=68694&highlight=NOE+schedule&page=2

No to the best of my knowledge it's still scheduled for the least week of january !

[Tazman1602]

No to the best of my knowledge it's still scheduled for the least week of january !

Take a look here 6-pt. Now scheduled for April release. No big deal for me.

http://castboolits.gunloads.com/showpost.php?p=754100&postcount=24

Art

[6pt-sika]

Take a look here 6-pt. Now scheduled for April release. No big deal for me.

http://castboolits.gunloads.com/showpost.php?p=754100&postcount=24

Art

Hmmmm you are correct :shock:

[SciFiJim]

I am closing this thread. The group buy is going into production in six weeks and I am running a supplemental group buy here.
432-265 RFGC Supplemental Group Buy (http://castboolits.gunloads.com/showthread.php?p=826682&posted=1#post826682)