Interest in "Ruger Only" .45 Colt mold?

[only1asterisk]

http://i70.photobucket.com/albums/i97/only1asterisk/454-330.jpg

330 grains in the sketch. .440" long nose, .325 meplat. ≠

[targetshootr]

Very much so.

[ddeaton]

what makes this Ruger only?

[Heavy lead]

what makes this Ruger only?

Probably length. Us Ruger 45 shooters are constantly handicapped by the stubby boolit designs made for the lopped off Colt cylinders.

Yup, I'd be in.

[runfiverun]

my o/m vaquero would nearly accept a full length 454 casull case.

[Hardcast416taylor]

I`d be interested. How many cavity would it be? Any idea of cost?

[only1asterisk]

what makes this Ruger only?

The design is too long for Colt and Colt clone cylinders. It will fit other revolvers, such as the Colt Anaconda, the .45 Colt cylinder of a Freedom Arms Model 83 or .460 S&W Magnums. There are others as well, but I lost my list of revolver cylinder lengths when my hard drive crashed last December.

[Down South]

I would be intrested in one depending. I'll keep an eye on this one. It may fit my Judge and it surely will fit my 460.

[45 2.1]

Something to look at:

[targetshootr]

The single lube groove would be easier if your sizer dies are set up that way, so you don't have to plug and unplug the holes.

[Heavy lead]

One groove, or two I care not, but much prefer to have it not checked in a Mihec Cramer style please.

[only1asterisk]

One groove, or two I care not, but much prefer to have it not checked in a Mihec Cramer style please.

I agree, either is fine by me.

[Nazgul]

I'm in.

Don

[Hardcast416taylor]

Whoa!!! What design are we talking about here? A multi groove 330 gr. non-H.P. or a 297 single lube groove H.P.? I may be old and slow, but I like to know what we are actually talking about here. :castmine: Robert

[only1asterisk]

Whoa!!! What design are we talking about here? A multi groove 330 gr. non-H.P. or a 297 single lube groove H.P.? I may be old and slow, but I like to know what we are actually talking about here.

Well, since the advent of MiHec's mold making venture everything has the option of being a cut as a hollow point. 45 2.1 has simply calculated the option into his drawing. Lots of people like the single lube groove for the ease of setting up their lube.

This is just a discussion. We'll hash out something that will work for most people.

[Roper1952]

I'm game, my H&R Buffalo Classic 45 carbine would love a nice big heavy boolit. My short barreled Blackhawk is a handfull though, I'll stick with lighter loads in it.

Don't see much need for a HP...

[uncowboy]

I love the HP Idea because of what I have read,Would it be possiable to have two pins made for each mold=1 HP the two cavities and =1set that would make the bullet have a flat metplat? I don't understand why this couldn't be done. It should just add the charge of the 2nd set of pins? J.Michael

[targetshootr]

Either one or two lube grooves is fine with me. This size 45 doesn't seem to come around very often.

[only1asterisk]

Either one or two lube grooves is fine with me. This size 45 doesn't seem to come around very often.

I'd really like to see this one go, but there have been so many good designs in the recent weeks maybe some folks are spent.

[ddeaton]

Sorry guys, I dont need any heavy stuff now.

[fivegunner]

can it be made in two cavity HP????? that would trip my trigger!!8-):Fire:

[Snyd]

I may be interested. But what I really would like though is a 350-360gr LBT style WLN like the Cast Performance 360gr for my 4 inch redhawk. How much $$$ I've never done this before, I'm a newbie still waiting on my order for my pot and moulds. I do however have 450lbs of ww ingots smelted ready to go!

[Mohillbilly]

I got 45 Rugers, and a Casull. Wonder if it'll feed in a Wrangler Winnie? It ought too. This heavy should have plenty of "thump" I'll bite.......

[rvpilot76]

I'll bite as well.

Kevin

[Hardcast416taylor]

Is this going to be a group buy or is this just a lot of "I Wannas"! Robert

[Snyd]

"I wanna" little more info like how many cavities and the price and what mould handles it will take.

[guninhand]

I could go for a 350-360 LBT, single cavity, but will consider 2 cavity, preferably made by MiHec. HP oK if still up in 350-360 gr range weight.

[mroliver77]

I love the HP Idea because of what I have read,Would it be possiable to have two pins made for each mold=1 HP the two cavities and =1set that would make the bullet have a flat metplat? I don't understand why this couldn't be done. It should just add the charge of the 2nd set of pins? J.Michael

Allready done, you only have to flip the pins in mihas mold to go from hp to solid point.
J

[targetshootr]

I'd like it to be a six cavity aluminum. And I'd like it to be here next week. For $15.

[New Lead Man]

"I'd like it to be a six cavity aluminum. And I'd like it to be here next week. For $15. "- targetshootr

I'll take two please.[smilie=1::mrgreen:

[Ken 45LC]

Just found this thread after asking about a heavy 45 in the colt thread. I'd go with a 350-360 gr hp for in the 45-70. Although I'd want a gas check on it.

I'd also like to keep it in a 2 cavity brass, Miha's brass moulds are a thing of beauty, and almost to pretty to use.

Thanks,
Ken

[Snyd]

I'm still interested in a 350-360gr LBT style.

[Hardcast416taylor]

I don`t see anything happening here except alot of guys saying this sounds like what they would want. Yes, I said I was interested, as did everyone else so far, so what happens now? Robert

[only1asterisk]

Yes, I said I was interested, as did everyone else so far, so what happens now? Robert

We wait.

Sometimes it takes a while. We only have about half the people needed. We may need to make some changes to attract more buyers.

[Dutch4122]

45 2.1's design in post #9 looks very interesting to me. I like the idea of switching the pins and going from a solid to a hollow point. Also prefer the single lube groove.

Just my 2 cents.:Fire:

[only1asterisk]

45 2.1's design in post #9 looks very interesting to me. I like the idea of switching the pins and going from a solid to a hollow point. Also prefer the single lube groove.

Just my 2 cents.:Fire:

I think the bullet in #9 is the going thing. I don't think anyone is strongly in favor of 2 lube grooves.

[only1asterisk]

I would take a couple of the 45 2.1 designs in thread #9 if HPable !

I would also love this one in GC for my single shot rifles ! :) :)

Jerry

Jerry,

Would you mind if the GC were a little heavier? Like 340?

[15bobcat]

I'd be interested if it was a Miha style with reversable pins and gas check option. Any thoughts on the diameter?
-Harold

[Heavy lead]

I got 45 Rugers, and a Casull. Wonder if it'll feed in a Wrangler Winnie? It ought too. This heavy should have plenty of "thump" I'll bite.......

I've got a trails end 94 Winchester that feeds a 360 grain long flat nose (.410 from crimp groove to meplat) like butter. Hits like a darn 45-70 with a heavy dose of 296 and accurate too.

[outdoorfan]

I may be interested. But what I really would like though is a 350-360gr LBT style WLN like the Cast Performance 360gr for my 4 inch redhawk. How much $$$ I've never done this before, I'm a newbie still waiting on my order for my pot and moulds. I do however have 450lbs of ww ingots smelted ready to go!


Like this one? This is a custom jobber that Veral did for me. 2/1 ww/pure gc'ed and lubed weighs in right at about 360 grains. Meplat is .4 and nose-to-crimp is about .385. I haven't killed anything with it yet, but it should hit like a hammer.

Edit: Forgot to add that it fits in my Blackhawk cylinder with room to spare.

[Snyd]

Ya, that looks pretty good. I wonder if I could get it to feed though in my Puma 92 454. The metplat looks a little fatter then the CP 360 gr and I think the bullet profile makes a difference in the little kitty. It sure would be a good thumper in the Redhawk though. I'm getting 1155fps with H110 and CP 360gr out if the 4 inch barrel. Should be good bear medicine if needed.

I just checked CP and the 360 WLN is "nose .390 meplat .355" according to CP. Yours just might feed in the levergun. Would you be willing sell me a few lubed with the gc to try out in my levergun? Shoot me a pm if you're willing. If they worked out I'd get the mould specs from you and just order one up.

[Heavy lead]

I hope this boolit is not going to turn into another general purpose boolit that will work in everything. Seems like everyone is asking whether this will feed in this or that. I believe that was the whole point here, for once to have a boolit made for a Ruger's long cylinder.
What's it going to be?

[Mohillbilly]

Right now the heavyist 45 I got is the Keith 310gr. GB, or the Lee 300 , however this could be the next heavy weight champeeeen, If the crimp is in the right place... Heavy Lead just where did you git your 360, and are the pics that outdoorfan shows what yall are talk'n about?What is the max weight of deminishing returns on 45 Colt? ie too much boolit,not enough powder? If they'd fit, I would shore like a Mihec six/crammer like those.

[Bulletlube]

Is this ever going to be a go?

[Matt_G]

I am interested in the original design per the drawing in post #9.
Single lube groove, PB.
Keep it for Ruger's only as originally planned.

[rvpilot76]

I am interested in the original design per the drawing in post #9.
Single lube groove, PB.
Keep it for Ruger's only as originally planned.

+1

Kevin

[only1asterisk]

Is this ever going to be a go?

Right now we only have about half the people we need.

[Matt_G]

Right now we only have about half the people we need.

I take it MiHec needs twenty to make this a go, is that correct?
By my count we only have ten so far...

[ELFEGO BACA]

i would be interested in a 4 to 6 cavity mold similar to post#1 or post#9 with no hollow point.

elfego

[Frozone]

I'm in for one of these also.

[Heavy lead]

I believe Mihec could make a gas check heavy off the same design for the 326 grain pb. I would take one of each in his brass blocks, I would use the heavy gc for the casull and the pb for the ruger. I know he is doing this with the 41 group buy and I'm in for both two.
What do guys think about that, we may be able to get to 20 I want this boolit. And for any of you that haven't had the pleasure of these Cramer style brass moulds, they are awesome, easy to cast and just simply a work of art he should be selling for twice as much.

[alamogunr]

I think I would like to have a "Ruger Only" .45 Colt Mihec mold. But this thread and all the other Mihec threads I follow, it seems like every post suggests a different configuration. I think I ordered a .41 Mihec mold. Can't tell from his site. At this point is there any possibility that this mold will be a hollow point/flat point w/plain base or GC(not both). Or will it be a swiss army mold with endless possibilities???
John
W.TN

[Heavy lead]

I believe the boolit in post #9 in the concensus thumbs up, I would certainly go for this mould, with Mihec's mould design you could enjoy a great hp and a penetrating solid as well. I would also like to see a design cut for a gas check as well. I believe he could do them in the same run with the same cherry. I would be in for both.
Don't want to see this one die.

[Matt_G]

I believe the boolit in post #9 in the concensus thumbs up, I would certainly go for this mould, with Mihec's mould design you could enjoy a great hp and a penetrating solid as well. I would also like to see a design cut for a gas check as well. I believe he could do them in the same run with the same cherry. I would be in for both.
Don't want to see this one die.

If a GC design is done with the same cherry, it would be done by cutting a longer/heavier bullet when doing the GC design, is that correct?
Or would we have to compromise the original PB design and make it shorter/lighter to accommodate the GC design?
I'm curious as to what the specs would be on both styles if this route is taken.

I don't want to see this one die either.

[Highland Drifter]

I would go for post #9. Ruger only, plain base, Mihec Cramer style 2 cavity H.P. brass mold.

Brian

[Mohillbilly]

Heavy lead I'm with you. nice look'n boolit for the blkhwks, and a longer,heavy,GC, for cassul and my winnie wrangler. All done on the same cherry.

[only1asterisk]

Heavy lead I'm with you. nice look'n boolit for the blkhwks, and a longer,heavy,GC, for cassul and my winnie wrangler. All done on the same cherry.

Ask 45 2.1 to make it so and lets see who all is in.

[targetshootr]

Not sure how these new GBs work but this one might lose a few takers if it's only a two cavity. The lightweight six cavities have ruined me for anything else.

[Heavy lead]

If a GC design is done with the same cherry, it would be done by cutting a longer/heavier bullet when doing the GC design, is that correct?Yes, this is correct.
Or would we have to compromise the original PB design and make it shorter/lighter to accommodate the GC design?No, the plain base would not be a comprimise
I'm curious as to what the specs would be on both styles if this route is taken.

I don't want to see this one die either.

I'm sure we could get 20 between the two, others seemed to have interest too.

[Heavy lead]

Not sure how these new GBs work but this one might lose a few takers if it's only a two cavity. The lightweight six cavities have ruined me for anything else.

Since this is to be a solid/hollow point Mihec's brass cavity cramer style hollow point is THE way to go, these are every bit as fast as a standard two cavity mould, I'm sure a three or four could be made, but honestly with a brute like this I'm sure a two will do. I casted 200 keepers in an hour last night from the 44/444 group buy hollow point last night after an initial casting and breaking in period a few days prior, they are awesome moulds. And if you want the solid point, turn the pins around, reinstall the lock ring and it works exactly like a plain old two cavity, so simple it's stupid. My feeling is these moulds, once you try them will ruin you for any more Lee moulds, same with Swede Nelson's 5 cavities, a big wow on those two as I have his 358429 group buy, it's like Christmas in July here in Paw Paw.

[sixshot]

I'll take one!

Dick

[Lloyd Smale]

if its a cramer style mold that has reversable pins and is a gas checked design id be in for one

[denul]

I'd be in for the post #9, 2 cavity, Mihec HP , PB

[Heavy lead]

if its a cramer style mold that has reversable pins and is a gas checked design id be in for one

The reversable pin cramer was the plan from the beginning, the option of a gas check was added????? hopefully, I want both, and am hoping we can get both.

[GLL]

Lloyd:

I also hope that the GC version will be available as an option on this buy. This would be a great HP bullet with GC for my single shot carbine ! :) :)

I would take a 2-cavity brass Cramer HP in PB as well as a second 2-cavity HP mould in GC !

Jerry

[Boomer Mikey]

What is the length of the nose from the meplate to the crimp groove for the bullet in post # 9 please?

I would be interested in this as well if in the 0.453"- 0.454" area. Don't care for a GC but would go that way if that's what everyone wanted.

Boomer :Fire:

[Frozone]

Just want to bump this back to the top.

I Really want one of these.


I would prefer a GC and a little heavier than the PB would be fine with me.

[45 2.1]

What is the length of the nose from the meplate to the crimp groove for the bullet in post # 9 please?

I would be interested in this as well if in the 0.453"- 0.454" area. Don't care for a GC but would go that way if that's what everyone wanted.

Boomer :Fire:

0.456" meplat to crimp groove.

[2 dogs]

I would have to have one of these in a 2 cavity HP option.

[Matt_G]

Ok, I think it's time to try and get a list together with what everyone wants and see where we stand.

Everyone is pretty much in agreement that the design in post #9 is what we want.
MiHec cramer style mould, single lube groove, 2 cavity for Rugers.
Now the question becomes, can we get this done with the option of a gas check.
The GC design would be cut with the same cherry and therefore would be slightly longer and heavier than the PB design in post #9.
I went through this thread and have compiled a list of people who have expressed interest.
If I have missed you or misinterpreted your wishes, please post and let us know.
I really want to see this one get off the ground!

only1asterisk - post #9 design - PB
GLL - post #9 design - PB and GC
Heavylead - post #9 design - PB and GC
Nazgul - post #9 design - PB
Hardcast416taylor - post #9 design - Base type unknown
Roper1952 - post #9 design - Base type unknown
Mohillbilly - post #9 design - PB and GC
rvpilot76 - post #9 design - PB
Matt_G - post #9 design - PB
Denul - post #9 design - PB
Lloyd Smale - post #9 design - GC
sixshot - - post #9 design - Base type unknown
2dogs - post #9 design - Base type unknown
alamogunr - post #9 design - PB
Highland Drifter - post #9 design - PB
Dutch4122 - post #9 design - PB
15bobcat - post #9 design - GC
Frozone - - post #9 design - Base type unknown

BoomerMikey, is the .456" meplat to crimp groove a show stopper for you? I know you wanted .453 to .454 and a PB boolit.

So it looks like we have 21 moulds between the GC and PB designs, perhaps more cause I'm sure I have probably missed a couple of folks.

I just wanted to try and get this a little more organized. [smilie=1:

[45 2.1]

It's not too much of a problem to make the GC version about the same weight as the PB version. A difference of 0.003" shouldn't cause concern in the meplat to crimp groove length as long as it is crimped well, but it could be shortened slightly also.

[targetshootr]

No two cavity molds for me, thanks. Or hps or gcs.

[Heavy lead]

The slightly heavier/longer gas checked boolit would be applauded by me. Like the list says I want both. I'm ready. I'm assuming we are talking still about Mihec's fine cramer style brass?

[GLL]

Heavy lead:

I am also getting two moulds !

One in PB and a second in GC !

The latter should work well in my single shot carbine.

Jerry

[tiny]

is there any idea how much the molds are going to cost . thanks

[alamogunr]

I would prefer a plain base but would take a GC base if that is what the majority want, especially if it is as 45 2.1 says that it need not be heavier than plain base.
John
W.TN

[Matt_G]

is there any idea how much the molds are going to cost . thanks

As of right now, assuming Mihec does this and his prices stay the same, a 2 cavity cramer style brass mould is $95.00 including shipping.

If I'm wrong guys please correct me!

[Matt_G]

Back to the top.

[New Lead Man]

I would be interested in one.

#9 Plain base.

[Frozone]

Back to the top.

Matt, I'd prefer a GC design.
If it's a little heavier than the PB so much the better.

[Matt_G]

Back to the top.

Just an FYI for everyone, I asked 45 2.1 if he would post new drawings that incorporate the PB and GC design being cut with the same cherry.
Hopefully he will find time to do that in the near future.

[45 2.1]

Sorry for the delay. Here it is........

[Matt_G]

Thank you sir!

[joeb4065]

First time to chime in on a GB, this looks like a great bullet, count me in for a plain base one, if this is still open...

When would we hear about how much they are, and when to send money?

Joe

[Idaho Sharpshooter]

I happen to have an Anaconda 45LC with a 4" barrel. Every so often I get a friend to cast me a few of his truncated cone 300gr. This is even better. 4-cavity with both ends HP pins.

I want one!!!!!


Rich

[750k2]

Just picked up a 45 Bisley - I'm in - Plain base is fine but can live checked.
HP and soild if that happens.
Can you post some sort of option price thingy - just ballpark?

I'll need a mold so I'm in:drinks:

[750k2]

Thought I'd bring this to the top.

Is this any closer to becoming reality?

[Matt_G]

Updated list:
only1asterisk - post #9 design - PB
GLL - post #9 design - PB and GC
Heavylead - post #9 design - PB and GC
Nazgul - post #9 design - PB
Hardcast416taylor - post #9 design - Base type unknown
Roper1952 - post #9 design - Base type unknown
Mohillbilly - post #9 design - PB and GC
rvpilot76 - post #9 design - PB
Matt_G - post #9 design - PB
Denul - post #9 design - PB
Lloyd Smale - post #9 design - GC
sixshot - post #9 design - Base type unknown
2dogs - post #9 design - Base type unknown
alamogunr - post #9 design - PB
Highland Drifter - post #9 design - PB
Dutch4122 - post #9 design - PB
15bobcat - post #9 design - GC
Frozone - post #9 design - GC
NewLeadMan - post #9 design - PB
joeb4065 - post #9 design - PB
750k2 - post #9 design - PB


It looks like we have 25 moulds total.

[Matt_G]

Thought I'd bring this to the top.

Is this any closer to becoming reality?

Thanks for the bump.
I guess it's time to PM MiHec and see what he has to say.
I'll try and get that done this morning.

[750k2]

BTT Any word yet?
just checkin in[smilie=s:

[Matt_G]

I sent Mihec a PM and he relied that he would come out to the thread and check it out.
I was hoping he would post here but obviously he has not.
He did say he was interested in doing this mould for us.
He is having some issues right now so I'm sure they take priority at the moment.

Thanks for the nudge.

[MDF99]

I'm in for a gas check mould whenever this buy starts.

[750k2]

I just committed to another buy so if you want to really bend me over you guys better hurry:groner:

[geargnasher]

Just picked up a 45 Bisley - I'm in - Plain base is fine but can live checked.
HP and soild if that happens.
Can you post some sort of option price thingy - just ballpark?

I'll need a mold so I'm in:drinks:


You sure this mould will fit your Bisley cylinder?

Just checkin'.

Gear

[geargnasher]

My 7-1/2" New Vaquero is licking its chops!!

I'm in for one as long as it is plain-based and casts at least .453" with WW alloy.

#9 design is fine. No hp for me unless the hp weight could be bumped to 330.

Gear

[750k2]

You sure this mould will fit your Bisley cylinder?

Just checkin'.

Gear

It should it's a Ruger Bisley

[Muskwa]

I'm in for a: post #9 design - 2 cavity - PB.

Muskwa

[geargnasher]

It should it's a Ruger Bisley

Ah! Didn't catch the Ruger part. Usually when one says just "Bisley" they are referring to the original Colt design made for the English pistol matches, or a copy thereof.

Gear

[Ctkelly]

I'd be in for post #9 2 cavity PB

[geargnasher]

Nudge, nudge! That's 3 or 4 more to the 25.

Gear

[azcoyhunter]

How much would this come out to for a NON GCed version?

I have a Ruger that would love this, but $$$ could mean a no go....

[750k2]

Any news yet:coffeecom

[750k2]

Just got my Ruger back and would like to see this go forward.
I need a mould as this one wont see copper.

[geargnasher]

I think everyone must be going for the LBT gb for "choose your own everything" .45 WFN. Very nice, and tempting, but I was wanting one of these.

Gear

[750k2]

I also looked at that.
I wanted this one but if this starts to peter out I'll make the jump as well.
Any word yet:confused:

[Matt_G]

I have sent Miha another PM asking him to let us know his thoughts on this GB.
Hopefully, I will know something in the next day or two.

[alamogunr]

I think everyone must be going for the LBT gb for "choose your own everything" .45 WFN. Very nice, and tempting, but I was wanting one of these.

Gear

Where is the LBT GB? I recently bought a couple of molds from Veral for my .475 L and haven't been following the GB's here very closely.

John
W.TN

[only1asterisk]

Mihec is already committed to 6 more designs. Maybe time to consider another vendor?

http://www.brp.castpics.net/

[Frozone]

If it isn't a 'Cramer' design I'm out.

[Heavy lead]

My vote is we stay on task and remain patient for Miha. His brass Cramer mould is a work of art and quick to use, well worth the wait IMO. This isn't your $30 Lee group buy for $70. It's a $85 mould that is worth $185 IMHO.

[750k2]

I'm hangin in there - Just anxious - Got the shootin iron, 1000 brass, cs. o primers
and a couple kegs of go stuff but no mould :sad:
I guess I'll send the cylinder off for some throat work - like they say - it can't hurt.

[geargnasher]

Where is the LBT GB? I recently bought a couple of molds from Veral for my .475 L and haven't been following the GB's here very closely.

John
W.TN

Here: http://castboolits.gunloads.com/showthread.php?t=63763.

Gear

[750k2]

????
Any news yet?
:killingpc

[MiHec]

Hi

I'm interested in doing this.
Right now I can not promise exact date as I'm having problems with getting free machines.

I'm looking to buy my own cnc...

I will inform you as soon as possible

[Matt_G]

Thanks for dropping in and letting us know Miha. :)

[Cayoot]

We had a crisis come unexpectedly upon us this spring, and I've been pretty much out of the loop for most things in life and on line. However, we are slowly (but not steadly) recovering. I haven't done any casting since last fall, but I'd sure like to try to get back into it.

I really like the look of the original post..it looks like it would be a real dependable penetrator in a short (5 inch) barrel Blackhawk.

If the money won't be required until next month, count me in for a p.b. and heavy version.

[Matt_G]

I really like the look of the original post..it looks like it would be a real dependable penetrator in a short (5 inch) barrel Blackhawk.

We are looking at doing the design in post #9.
The money won't be due for at least another month.
Still interested?

[geargnasher]

I'm still interested. I would like brass, 2 cavity, pb preferable but GC ok if that's majority need, Cramer design HP ok but if it has to be I want reversible pins with blanks on one end (option to make regular rfn's) or be able to saw them off, #9 design single-groove just fine.

The issue with pb hps of this weight is alloy choice and velocity limitations. If you push this fast enough for good expansion with a low-antimony or Pb/Sn binary the boolit is likely to strip the rifling or skid enough to cause issues (I'm thinking revolvers here), mainly gas-cutting and leading. If the alloy is hard enough or alloyed for heat-treating it will be too brittle for good hollow point mushrooming without the nose shattering. This is why I tend to shy away from hp designs for heavy hunting boolits and let the big meplat do the work. Heck, it's a .45!!!! How big do you want it?

Anybody have any input on this?

The wait is no problem as long as Mihec makes them.

What's the diameter of the nose base? I'm looking for a full-diameter nose on this one, no bore riders for me please.

Gear

[Heavy lead]

Wondered what happened to this.
I'm a big fan of Miha's Cramer brass, but I know his back log is getting real bad and he's been having problems. Anyone have any thoughts on asking NOE to run this and offer both solid, RG hollow point as well as gas checked and plain base like Blammer is running for that big 44 mould?

[only1asterisk]

Wondered what happened to this.
Anyone have any thoughts on asking NOE to run this...

He's actually offered.


and offer both solid, RG hollow point as well as gas checked and plain base like Blammer is running for that big 44 mould?

I don't know about all that, but I'm open to discussion if Swede is willing.

[geargnasher]

I'm ok with NOE, but it would be aluminum and I could just as well get exactly what I want from LBT rather than compromise on a group design.....the brass would be worth the wait to me if Mihec can/will do it in brass.

Gear

[750k2]

???
:killingpc

[750k2]

Is this dead??

[Matt_G]

Miha said in a previous post he was interested in doing this mould.
You could PM him and ask where it is in the line.
I'm sure he will get around to it. He's had problems and just bought or leased? a new CNC machine. He has to pay for that puppy somehow.

[kodiakken]

Does anyone know if this boolit would fit in a Smith & Wesson Mountain Gun in 45 Colt? If it would I think I would be interested, especially if it's one of Miha's brass hollow point molds.

Ken Gordon
Fairbanks, Alaska

[Matt_G]

Kodiakken, I can't answer your question.
Hopefully someone else will.

To everyone, I sent Miha a PM asking him to stop by this thread and let us know whether or not this mould is on his to do list.

[geargnasher]

Thanks, Matt.

I'm still in, but in no hurry.

Gear

[MiHec]

I love the HP Idea because of what I have read,Would it be possiable to have two pins made for each mold=1 HP the two cavities and =1set that would make the bullet have a flat metplat? I don't understand why this couldn't be done. It should just add the charge of the 2nd set of pins? J.Michael

All my molds have reversible pins - so hp or solid in one design

By the way I will do this mold.
As we speak I'm setting up my shop.
I bought a Haas CNC (Super mini mill)
Thinks will be much faster now.

[Matt_G]

Thanks for stopping by and letting us know you'll do this mould MiHec. :bigsmyl2:

[geargnasher]

We're still talking brass blocks, right?

Gear

[jrayborn]

Count me in for this one.

[Heavy lead]

So it there a count here? I've got 5 Ruger 45's so I still need one.

[wdr2]

What is the as cast diameter with WW for this mold design?

[45 2.1]

What is the as cast diameter with WW for this mold design?

Since MiHec has this mold on his schedule, the diameter can be anywhere in the correct range. I would imagine somewhere in the 0.452" and 0.454" range.

[Frozone]

I said I'd take one of these, but let me qualify that. I have no use for a mould that drops smaller than .4545 in WW.

[medicdave]

I'd want one.

[GLL]

How about an updated LIST ?

Jerry

[fivegunner]

I would be intersted in the HP from post :-)9

[wdr2]

I am interested in the Post 9 design, PB, about 0.452-0.453 dia, two cavity brass mold from MiHec.

[geargnasher]

How about an updated LIST ?

Jerry

+1.

Gear

[Changeling]

Seems to be lacking in grease groove area.

[waksupi]

Seems to be lacking in grease groove area.

No problem, I can sell some loob grooves for the design.

[9.3X62AL]

Ric can always be counted on for a loob gruve supplement. On deck, and tending to bizness, as ever.

[geargnasher]

Ric can always be counted on for a loob gruve supplement. On deck, and tending to bizness, as ever.

Indeed, prowling the forums and loob groove scrap yards late at night searching for strays needing a good home.......

Gear

[geargnasher]

Is this thing dead?

Anyone know if we're still on the list with Mihec?

Gear

[sljacob]

I am interested In this mold, if it gets off the ground you can count me in on one.

[Matt_G]

I'm sorry for not keeping the list updated over the past few months guys. Real life has been a bear and until a few days ago I hadn't even been on the forums for a few months.

I know that MiHec has posted twice in this thread that he wants to do this mould. However, I just looked at his site and I do not see this mould listed in the upcoming group buys. :(

I sure would like for him to do this mould. I got one of his H&G 503 brass cramer style moulds a few weeks back and it is a VERY nice mould. Having said that though, maybe we should look at having NOE run this. Will they do brass or would it be aluminum? (personal bias, I hate aluminum mould blocks...)
Opinions?

Anyways, here is an updated list:

only1asterisk - post #9 design - PB
GLL - post #9 design - PB and GC
Heavylead - post #9 design - PB and GC
Nazgul - post #9 design - PB
Hardcast416taylor - post #9 design - Base type unknown
Roper1952 - post #9 design - Base type unknown
Mohillbilly - post #9 design - PB and GC
rvpilot76 - post #9 design - PB
Matt_G - post #9 design - PB
Denul - post #9 design - PB
Lloyd Smale - post #9 design - GC
sixshot - post #9 design - Base type unknown
2dogs - post #9 design - Base type unknown
alamogunr - post #9 design - PB
Highland Drifter - post #9 design - PB
Dutch4122 - post #9 design - PB
15bobcat - post #9 design - GC
Frozone - post #9 design - GC (no use for a mould that drops smaller than .4545 with WW alloy)
NewLeadMan - post #9 design - PB
joeb4065 - post #9 design - PB
750k2 - post #9 design - PB
geargnasher - post #9 design - PB (As long as it casts .453 with WW alloy)
Muskwa - post #9 design - PB
Ctkelly - post #9 design - PB
Cayoot - post #9 design - PB and GC
jrayborn - post #9 design - Base type unknown
medicdave - post #9 design - Base type unknown
sljacob - post #9 design - PB and GC
Thaine - post #9 design - PB
buckndee - post #9 design - Base type unknown
Old Ed - post #9 design - PB

[Thaine]

Matt,

Put me down for one of these if we are going with the Miha 2 cavity brass mould. I have 5 of his moulds and they are excellent. I don't mind a wait for his product. The reason he is backlogged IMHO is because of the quality of his work. SO:

1ea. 2 cavity Crammer style in plain base please

[buckndee]

I would like a Miha 2 cavity HP mould.

[Highland Drifter]

I'm still in for a brass Cramer style H.P. mold, and am willing to wait until Miha gets to this one. I don't really care for the aluminum floppy pin style H.P. molds.

Brian

[Matt_G]

Added Thaine and buckndee to the list.

buckndee, are you interested in a plain base or gas check boolit?
I would rather wait for a mould from Miha as well.

[wdr2]

I recently purchased the MiHec RCBS 45-270-SAA mold instead. Please delete my name from this GB. Thanks, wdr2

[Matt_G]

I recently purchased the MiHec RCBS 45-270-SAA mold instead. Please delete my name from this GB. Thanks, wdr2

Done.

[sljacob]

pb and gc cramer form miha....I don't mind the wait I will give me time to put the coin together as I am in three other gb's at this time.

[sljacob]

mat

You have me on the list twice, my post yesterday was to add the base type I wanted as you had me down as unknown.


jake

[Matt_G]

Fixed it Jake.
I should know better than to do this stuff before I've had ALL my coffee in the morning! :coffee:

[Old Ed]

I'll take a Mihec 2 cavity PB. I don't mind the wait.

Ed

[Matt_G]

Added you to the list Old Ed.

I also want to let you all know I sent Miha a PM asking if would add us to the upcoming group buy list on his site.
I'm awaiting a reply. Once I hear from him, I'll update again.

[Old Ed]

Thanks Matt.

Ed

[jrayborn]

I'm on the list already, I would like a Mihec HP cut for gas checks if this gets going. If NOE does it I may need to make a change to the style.

Thanks!!

jrayborn

[Matt_G]

Time for an updated list:

1. only1asterisk - post #9 design - PB
2 - 3. GLL - post #9 design - PB and GC
4 - 5. Heavylead - post #9 design - PB and GC
6. Nazgul - post #9 design - PB
7. Hardcast416taylor - post #9 design - Base type unknown
8. Roper1952 - post #9 design - Base type unknown
9 - 10. Mohillbilly - post #9 design - PB and GC
11. rvpilot76 - post #9 design - PB
12. Matt_G - post #9 design - GC
13. Denul - post #9 design - PB
14. Lloyd Smale - post #9 design - GC
15. sixshot - post #9 design - Base type unknown
16. 2dogs - post #9 design - Base type unknown
17. alamogunr - post #9 design - PB
18. Highland Drifter - post #9 design - PB
19. Dutch4122 - post #9 design - PB
20. 15bobcat - post #9 design - GC
21. Frozone - post #9 design - GC (no use for a mould that drops smaller than .4545 with WW alloy)
22. NewLeadMan - post #9 design - PB
23. joeb4065 - post #9 design - PB
24. 750k2 - post #9 design - PB
25. geargnasher - post #9 design - PB (As long as it casts .453 with WW alloy)
26. Muskwa - post #9 design - PB
27. Ctkelly - post #9 design - PB
28 - 29. Cayoot - post #9 design - PB and GC
30. jrayborn - post #9 design - GC
31. medicdave - post #9 design - Base type unknown
32 - 33. sljacob - post #9 design - PB and GC
34. Thaine - post #9 design - PB
35. buckndee - post #9 design - Base type unknown
36. Old Ed - post #9 design - PB
37. Skimmerhead - post #9 design - GC

As you can see we have 37 moulds on the list, 11 of which are gas check design.

I still have not heard back from Miha. I know that he is busy finishing up the .380 - Makarov moulds. As soon as I hear something I will pass it on.
Hope everyone is having a nice weekend. :)

[GLL]

Update?

Now officially one year old ! :)

Jerry

[Matt_G]

I have not received a reply to my PM from Miha.
I did resend that PM today.
Hopefully I'll hear from him. I know he is very busy.

[skimmerhead]

hey matt! you can put me down for a 2 cav. g c brass hp with both set of pins

skimmerhead

[Matt_G]

hey matt! you can put me down for a 2 cav. g c brass. wouldn't mind hp either. thanks!

Done.
Nice thing about Mihec's moulds; you can cast solid or HP just by flipping the pins.

[skimmerhead]

any news?

skimmerhead

[geargnasher]

Maybe we could get on Swede's list and get this produced by, say, Jan 2011 ( first opening per his currently posted production schedule), would that be any faster?

Gear

[MiHec]

Boys - I'm looking and planning.

It is hard to say exact schedule. Many small problems every day.

You must know this is not my primary job. (I wish it could be :?)

[Matt_G]

Boys - I'm looking and planning.

It is hard to say exact schedule. Many small problems every day.

You must know this is not my primary job. (I wish it could be :?)

Understood Miha.
Thanks for checking in and giving us an update.
I sure do appreciate it and I'm sure everyone else does as well.

[skimmerhead]

not pushing for a date, just wanted to know if you were going to do this mold, Miha i will wait if you do this mold. you have been very kind to me in the past few weeks, and now i must repay your kindness by purchaseing as many of your masterpieces as possible. thank you!

skimmerhead:castmine:

[white eagle]

I 'like it tooo

[pps]

If it's the cramer style #9 (hollow point) plain base, then count me in.

Thanks

Looking at getting a blackhawk in 45 colt and this looks like a great boolit.

Oh, if one of the points could be the pentagonal as in the RCBS 45-270-SAA in the other thread that would be even sweeter still.

[Matt_G]

Time for an updated list:

1. only1asterisk - post #9 design - PB
2 - 3. GLL - post #9 design - PB and GC
4 - 5. Heavylead - post #9 design - PB and GC
6. Nazgul - post #9 design - PB
7. Hardcast416taylor - post #9 design - Base type unknown
8. Roper1952 - post #9 design - Base type unknown
9 - 10. Mohillbilly - post #9 design - PB and GC
11. rvpilot76 - post #9 design - PB
12. Matt_G - post #9 design - GC
13. Denul - post #9 design - PB
14. Lloyd Smale - post #9 design - GC
15. sixshot - post #9 design - Base type unknown
16. 2dogs - post #9 design - Base type unknown
17. alamogunr - post #9 design - PB
18. Highland Drifter - post #9 design - PB
19. Dutch4122 - post #9 design - PB
20. 15bobcat - post #9 design - GC
21. Frozone - post #9 design - GC (no use for a mould that drops smaller than .4545 with WW alloy)
22. NewLeadMan - post #9 design - PB
23. joeb4065 - post #9 design - PB
24. 750k2 - post #9 design - PB
25. geargnasher - post #9 design - PB (As long as it casts .453 with WW alloy)
26. Muskwa - post #9 design - PB
27. Ctkelly - post #9 design - PB
28 - 29. Cayoot - post #9 design - PB and GC
30. jrayborn - post #9 design - GC
31. medicdave - post #9 design - Base type unknown
32 - 33. sljacob - post #9 design - PB and GC
34. Thaine - post #9 design - PB
35. buckndee - post #9 design - Base type unknown
36. Old Ed - post #9 design - PB
37. Skimmerhead - post #9 design - GC
38. pps - post #9 design - PB

[chadbr]

me me me - chadbr -a-t- yahoo.com

[Chapped Lips]

okay.....keep the snickering and ROTLRFLOL to a minimum.....but would this boolit work in a MARK 1 GRIZZLY in 45 win mag?.........i have a 3 screw blkhawk in 45colt too.....i'm really new at this but am interested.....

[Matt_G]

me me me - chadbr -a-t- yahoo.com

chadbr;
You want a plain base or a gas check mould?

[DAFzipper]

Put me down for #9 PB if funds are available when the mold runs. Kind of hard to tell without a time frame. Not complaining, the budget seems to get tighter every month!

[cptinjeff]

If this goes I'd like a PB and GC (post #9) if they would be in the same mould.....if not...PB is fine.

[Chapped Lips]

i'd be interested in one in PB.....

[skimmerhead]

hey matt will penta pins be available? if so i'd like a set.

skimmerhead

[Matt_G]

Time for an updated list:

1. only1asterisk - post #9 design - PB
2 - 3. GLL - post #9 design - PB and GC
4 - 5. Heavylead - post #9 design - PB and GC
6. Nazgul - post #9 design - PB
7. Hardcast416taylor - post #9 design - Base type unknown
8. Roper1952 - post #9 design - Base type unknown
9 - 10. Mohillbilly - post #9 design - PB and GC
11. rvpilot76 - post #9 design - PB
12. Matt_G - post #9 design - GC
13. Denul - post #9 design - PB
14. Lloyd Smale - post #9 design - GC
15. sixshot - post #9 design - Base type unknown
16. 2dogs - post #9 design - Base type unknown
17. alamogunr - post #9 design - PB
18. Highland Drifter - post #9 design - PB
19. Dutch4122 - post #9 design - PB
20. 15bobcat - post #9 design - GC
21. Frozone - post #9 design - GC (no use for a mould that drops smaller than .4545 with WW alloy)
22. NewLeadMan - post #9 design - PB
23. joeb4065 - post #9 design - PB
24. 750k2 - post #9 design - PB
25. geargnasher - post #9 design - PB (As long as it casts .453 with WW alloy)
26. Muskwa - post #9 design - PB
27. Ctkelly - post #9 design - PB
28 - 29. Cayoot - post #9 design - PB and GC
30. jrayborn - post #9 design - GC
31. medicdave - post #9 design - Base type unknown
32 - 33. sljacob - post #9 design - PB and GC
34. Thaine - post #9 design - PB
35. buckndee - post #9 design - Base type unknown
36. Old Ed - post #9 design - PB
37. Skimmerhead - post #9 design - GC
38. pps - post #9 design - PB
39. chadbr - post #9 design - PB
40. DAFzipper - post #9 design - PB
41. cptinjeff - post #9 design - PB
42. Chapped Lips - post #9 design - PB
43. fivegunner - post #9 design - GC

[Matt_G]

cptinjeff I'm 99% sure Miha will NOT do a GC and a PB in the same blocks.
That's why I have you down for the PB only.

Skimmerhead, all of Miha's recent moulds have shipped with round and penta pins.
I seriously doubt Miha will change that.
If he does, we will all get plenty of notice before the blocks are on the machine.

[chadbr]

I'll take the plain base - sorry for not posting originally.

[MiHec]

cptinjeff I'm 99% sure Miha will NOT do a GC and a PB in the same blocks.
That's why I have you down for the PB only.

Skimmerhead, all of Miha's recent moulds have shipped with round and penta pins.
I seriously doubt Miha will change that.
If he does, we will all get plenty of notice before the blocks are on the machine.

I can't go PB and GC in same blocks because of HP pins lenght.

Penta and round pins are standard issue for each mold where this is possible.

[fivegunner]

Hi, could you put me in for one of these , post #9 GC. :lovebooli

[pps]

I forgot to ask what brand of handles the mold takes.

[Matt_G]

fivegunner, you've been added to the list.

pps, Miha's moulds take Lee 6 cavity handles.

[Heavy lead]

OK, I'm still all for this group buy, but I'm wondering, especially since it has taken so long and also since we seem to have some 40 moulds, and Miha has ventured into a new area of 4 cavity brass, well could this be offered for those that wish a 4 cavity as well. I would just love to have this done in a 4 cavity cramer, if not a cramer then how about a 4 cavity solid option to go with the 2 cavity cramer? I'm thinking based on shop times we're looking at a couple months anyway, so when he gets the tooling it would be nice to get them all done, rather than run another buy down the road. I can't wait to unleash some forearm wrenching rath with some of these big dawgs.[smilie=w:[smilie=w:

[skimmerhead]

bump


skimmerhead:lovebooli

[Chapped Lips]

any idea when this might be rolled into the active buy arena?

[pps]

any idea when this might be rolled into the active buy arena?

+1. Just a rough estimate on time frame would be nice. Also, how many molds need to be ordered to make it worthwhile to be manufactured?

[skimmerhead]

pps miha said he would do this mold, i suppose it's on his list of molds to do. he's very busy. you can check his site M P molds and check his list. i think he has the cherry. read all the post in this thread, has aa the info.


skimmerhead

[pps]

pps miha said he would do this mold, i suppose it's on his list of molds to do. he's very busy. you can check his site M P molds and check his list. i think he has the cherry.


skimmerhead

Cool. After seeing his other work in some of the other threads I just feel like a kid in a candy shop.

Very nice work on the web page too.

[Heavy lead]

Seems there is enough interest. I would think 43 moulds would be a good number for a group buy.

[Chapped Lips]

just a nudge

[Chapped Lips]

just a ping.....

[geargnasher]

COUNT ME OUT ON THIS ONE.

I'm disappointed. Waited over a year for this to get rolling and can't even get an affirmative answer from the proposed maker as to when he might get around to it. I'm going ot order one from Veral.

Gear

[MiHec]

COUNT ME OUT ON THIS ONE.

I'm disappointed. Waited over a year for this to get rolling and can't even get an affirmative answer from the proposed maker as to when he might get around to it. I'm going ot order one from Veral.

Gear

Sorry. This one is active. 45 2.1 provided drawings and I will open order page in few days.

You must understand I'm one man band (construction, ordering thinks, making things.....).

[Matt_G]

Miha, what do you think of Heavy Leads idea quoted below?
Obviously, we don't know what interest would be in a four cavity solid yet. Heavy Lead is interested, as am I. If your interested in doing this we can gauge the interest in a four cavity solid to go with the 2 cavity cramer.

BTW, thanks for posting and bringing us all up to speed.

OK, I'm still all for this group buy, but I'm wondering, especially since it has taken so long and also since we seem to have some 40 moulds, and Miha has ventured into a new area of 4 cavity brass, well could this be offered for those that wish a 4 cavity as well. I would just love to have this done in a 4 cavity cramer, if not a cramer then how about a 4 cavity solid option to go with the 2 cavity cramer? I'm thinking based on shop times we're looking at a couple months anyway, so when he gets the tooling it would be nice to get them all done, rather than run another buy down the road. I can't wait to unleash some forearm wrenching rath with some of these big dawgs.[smilie=w:[smilie=w:

[Matt_G]

Geargnasher, in light of Miha's post above, do you still want out?

[southpaw]

What is the dia. for this one? I just read all ten pages and all I found was an I think.

Jerry Jr.

[Heavy lead]

Based on the quality and castibility of my new 4 cavity brass in the 270saa, I'd strongly suggest some bandwagon jumping (on, not off) on the 4 banger, THE best mould I've ever had, period.

[geargnasher]

Geargnasher, in light of Miha's post above, do you still want out?

Well, if we're that close, go ahead and count me in again. I wasn't faulting you, Matt, there have been a lot of timeline inquires all along the way and only one or two response from MiHec, and I was getting a little burned out on being in the dark. If I had dozens of customers chomping at the bit to get a product, I'd sure take two minutes to drop a line to them once in a while updating my manufacturing progress/schedule.

How much for the 4-cavity and I'll refrain from ordering one somewhere else?

Gear

[Heavy lead]

I almost was thinking the same way as Gear to be honest, but you know these brass moulds are the best, I really, really want a 4 cavity though if it is at all possible, I just don't see myself shooting a whole lot of hollow points.
I'm waiting, this mould will be worth it.

[Matt_G]

How much for the 4-cavity and I'll refrain from ordering one somewhere else?

This buy wasn't for a 4 cavity mould. It's for a 2 cavity cramer style HP mould.
Now, I am waiting on a reply to my question in post 199 about doing a 4 cavity solid in conjunction with the 2 cavity HP, assuming enough interest is there to make it viable for Miha.

Having said all that, the last few 2 cavity cramer style moulds I bought from Miha had two sets of pins and cost $93.00 plus $15.00 shipping for a total of $108.00

I got in on the 4 cavity solid brass 45-270-SAA mould and that was $80.00 plus $20.00 (heavier) for a total of one C-Note.

@Southpaw:
I'm sending a pm to Miha and 45 2.1 to find out exactly what diameter this was drawn up as.

[geargnasher]

Thanks, Matt.

I'll stick with the original plan of a two-banger with reversible cramer spuds.

Gear

[MDF99]

Please count me in for one Cramer HP-GC mold. Thanks.

[Matt_G]

Time for an updated list:

1. only1asterisk - post #9 design - PB
2 - 3. GLL - post #9 design - PB and GC
4. Heavy lead - post #9 design - PB
5. 2 dogs - post #9 design - PB
6. Nazgul - post #9 design - PB
7. Hardcast416taylor - post #9 design - Base type unknown
8. Roper1952 - post #9 design - Base type unknown
9 - 10. Mohillbilly - post #9 design - PB and GC
11. rvpilot76 - post #9 design - PB
12. Matt_G - post #9 design - GC
13. Denul - post #9 design - GC
14. Lloyd Smale - post #9 design - GC
15. sixshot - post #9 design - Base type unknown
16. alamogunr - post #9 design - PB
17. Highland Drifter - post #9 design - PB
18. Dutch4122 - post #9 design - PB
19. 15bobcat - post #9 design - GC
20. Frozone - post #9 design - GC (no use for a mould that drops smaller than .4545 with WW alloy)
21. NewLeadMan - post #9 design - PB
22. joeb4065 - post #9 design - PB
23. 750k2 - post #9 design - PB
24. geargnasher - post #9 design - PB (As long as it casts .453 with WW alloy)
25. Muskwa - post #9 design - PB
26. Ctkelly - post #9 design - PB
27 - 28. Cayoot - post #9 design - PB and GC
29. medicdave - post #9 design - Base type unknown
30 - 31. sljacob - post #9 design - PB and GC
32. Thaine - post #9 design - PB
33. buckndee - post #9 design - Base type unknown
34. Zeus - post #9 design - GC
35. Skimmerhead - post #9 design - GC
36. pps - post #9 design - PB
37. chadbr - post #9 design - PB
38. DAFzipper - post #9 design - PB
39. cptinjeff - post #9 design - PB
40. Chapped Lips - post #9 design - PB
41. fivegunner - post #9 design - GC
42. MDF99 - post #9 design - GC
43. Southpaw - post #9 design - GC

[Matt_G]

Received an answer to my PM from Miha.
Diameter as cast will be .454
He's hoping to get an order page up on his site for this buy soon.

[Matt_G]

Miha is willing to do a 4 cavity solid brass mould in this design as well.
A companion mould if you will. :)
We will need a minimum of 15 orders to make that a go.

I have started another thread for this companion mould.
http://castboolits.gunloads.com/showthread.php?t=95574

[2 dogs]

Matt, please put me down for a plain base mold, and Im going to sign up for the companion solid mold to this one too!

[Heavy lead]

I would like to only have one of these please, as I've added two 4 bangers, I'd like to have the plain base order kept and cancel the gas check.
Thanks Matt

[Matt_G]

2 dogs and Heavy lead, it's done.
FYI 2 dogs, I put you in the list at #5.

[Old Ed]

Matt, put me down for a 4 cavity plain base and cancel the other one. Thanks.

Any idea when this will be a go?

Ed

[Matt_G]

Matt, put me down for a 4 cavity plain base and cancel the other one. Thanks.

Any idea when this will be a go?

Ed

Ed, I assume you mean cancel this one (cramer 2 cavity HP) and put you down for a PB in the 4 cavity solid. Is that correct?
If so, acknowledge that here and I'll remove you from this buy.

If you wouldn't mind, please post in the following thread to get on the 4 cavity solid buy.
http://castboolits.gunloads.com/showthread.php?t=95574

[southpaw]

Matt,

Put me down for a GC model please.

Thanks.

Jerry Jr.

[Matt_G]

Your on the list Jerry.
Welcome aboard!

[Zeus]

I'll take one with the gas check option!!! Thanks :)

gswaggart at hotmail dot com

[Old Ed]

That's what I meant Matt. I'll post on the other side. Thanks.

Ed

[Matt_G]

Zeus,
Welcome aboard. I put on the list at #35. You took Old Ed's spot in the line.

[jrayborn]

Matt

Please drop me from this mold, I would like to get in on the 4 cavity. I will post in that thread, thanks!

Jon

[Matt_G]

It's done Jon.

[denul]

Matt - if its not too late - change mine from PB to GC -thanks -Denul

[Matt_G]

Time for an updated list:

1. only1asterisk - post #9 design - PB
2 - 3. GLL - post #9 design - PB and GC
4. Heavy lead - post #9 design - PB
5 - 6. 2 dogs - post #9 design - PB and GC
7. Nazgul - post #9 design - PB
8. Roper1952 - post #9 design - Base type unknown
9. Mohillbilly - post #9 design - GC
10. rvpilot76 - post #9 design - PB
11. Matt_G - post #9 design - GC
12. Denul - post #9 design - PB
13. Lloyd Smale - post #9 design - GC
14. sixshot - post #9 design - Base type unknown
15. alamogunr - post #9 design - PB
16. Highland Drifter - post #9 design - PB
17. Dutch4122 - post #9 design - PB
18. 15bobcat - post #9 design - GC
19. Frozone - post #9 design - GC (no use for a mould that drops smaller than .4545 with WW alloy)
20. NewLeadMan - post #9 design - PB
21. joeb4065 - post #9 design - PB
22. 750k2 - post #9 design - PB
23. geargnasher - post #9 design - PB (As long as it casts .453 with WW alloy)
24. Muskwa - post #9 design - PB
25. Ctkelly - post #9 design - PB
26 - 27. Cayoot - post #9 design - PB and GC
28. medicdave - post #9 design - Base type unknown
29 - 30. sljacob - post #9 design - PB and GC
31. Thaine - post #9 design - PB
32. buckndee - post #9 design - Base type unknown
33. Zeus - post #9 design - GC
34. Skimmerhead - post #9 design - GC
35. pps - post #9 design - PB
36. chadbr - post #9 design - PB
37. DAFzipper - post #9 design - PB
38. cptinjeff - post #9 design - PB
39. Chapped Lips - post #9 design - PB
40. fivegunner - post #9 design - GC
41. MDF99 - post #9 design - GC
42. Southpaw - post #9 design - GC
43. Down South - post #9 design - GC
44. Texinoz - post #9 design - GC
45. bbailey7821 - post #9 design - GC
46. WMB30 - post #9 design - PB
47. cast-n-blast - post #9 design - PB

[Hardcast416taylor]

Drop me from the list, I said I was interested - not that I would order a mold.Robert

[Matt_G]

Done Robert.

[2 dogs]

Where are we at on this mold???

I have missed MiHec's "link" to sign up a couple of times and dont want to miss it here!!!

[Matt_G]

He hasn't posted a link yet 2 dogs.
Hopefully that will happen soon.

[Texinoz]

Hi Gents,
I have just joined this forum. I would like to add my name for intended purchase.
My vote is for the post #9 design, 2 cavity brass with Gas Check.

[Down South]

I'm dropping off of the 4 banger solid nose for this one Matt. Put me on the list here for a GC mould. I'll post over on the other thread to help keep things straight.

[Mohillbilly]

Matt now that the 4 cav solid nose is running may I make a change ? I would like to drop the (PB) plain base mold here. and I will go to the other thread and order a 4 cav solid there. Thank you

[Matt_G]

Matt now that the 4 cav solid nose is running may I make a change ? I would like to drop the (PB) plain base mold here. and I will go to the other thread and order a 4 cav solid there. Thank you

Dropped the PB for ya. You still want the GC right?

[Matt_G]

Hey everyone,

Just an FYI to let you know that I have sent Mihec a PM asking for a status update on this one.
As soon as I hear back from him I'll post.

[Down South]

Looks like he will be starting it in about a week acording to the reply that I got from him on a GB that I'm doing. Post #60 in the link below.

http://castboolits.gunloads.com/showthread.php?t=95056&page=3

[Mohillbilly]

Both GC, a two hole HP , and a four hole solid. Thanks john

[white eagle]

Tom at Accurate Molds
has one of those in his catalog
I have one they are sweet

[bbailey7821]

Is this one closed? I would like a 2 cavity GC HP, Penta pins, and a nose punch if it isn't.

[MiHec]

Is this one closed? I would like a 2 cavity GC HP, Penta pins, and a nose punch if it isn't.

Not yet.

Just to let you know I have all prepaired. Now to the machine....;)

[bbailey7821]

Originally Posted by bbailey7821
Is this one closed? I would like a 2 cavity GC HP, Penta pins, and a nose punch if it isn't.

Not yet.

Just to let you know I have all prepaired. Now to the machine....

Please put me down for a 2 cavity GC, w/ Penta pins, and a nose punch

email is bbailey7821 at Hotmail dot Com

[denul]

I hate to do this, but please change me back to plain base HP ;2 cavity, all available pins. Sorry for the confusion. dennis dot a dot ulrich at gmail.com

[Matt_G]

It's changed denul.

[Matt_G]

That's great news Miha!
Thanks for posting and letting us know. [smilie=w:

bbailey7821, you are on the list.
Welcome aboard. 8-)

If anyone else wants one of these moulds, you best get on the list NOW!!

[WMB30]

Put me down for one Plain Base Post # 9 THANKS
wmb30 at att dot net

Bill

[Matt_G]

Welcome aboard Bill. [smilie=w:

[bbailey7821]

Forgive me, but... Is there a drawing of the final version, yet? There may have been one shown in the previous posts, but I wasn't able to ascertain.

[cast-n-blast]

Count me in ! Plain base ! jeffrey dot hoover at montgomerycountymd dot gov

[Matt_G]

cast-n-blast, you've been added to the list, welcome!

bbailey7821 the only pic/drawing is in post #9, first page.
45.2.1 doesn't post fully dimensioned drawings anymore.

[bbailey7821]

That's what I was looking for, Matt. Have a Good Turkey Day!

[2 dogs]

Ive decided I not only would like one of these with a plain base but please put me down for an additional mold with the GC option as well.

Thanks!

[Matt_G]

List has been updated 2 dogs.
47 moulds and counting. [smilie=w: