Wasalmonslayer
06-18-2019, 12:38 AM
Hello Gentleman I am helping out with this buy it is being run in conjunction with another board to help boost mold numbers so we can get to the magic 100 pin minimum.
If anyone has any questions I can find out the answer.
It fits the 300 Blackout, 300 Savage and 7.62x39, 7.65 BM and several others if orbited larger besides the normal complement of normal 30 calibers. Offered bullet diameters will be 0.311" and 0.313"..... both will cast out about a half thousandth larger dependent on your alloy of choice.
We will need enough to make Miha's pin requirements. We will run this until we get the number we need (probably 34 HP molds due to current supply conditions) or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.
I am offering these choices: 3 cavity PBHP and 3 cavity GCHP on MiHec's two cavity brass blocks , 6 cavity PB solid and 6 cavity GC solid on MiHec's four cavity brass blocks , 8 cavity PB solid aluminum, 8 cavity GC solid aluminum.
NOTE: THIS BULLET IN 0.311" SIZE WILL NOT FIT WHEN POWDER COATED IN TIGHT THROATED RIFLES. They will fit the larger 0.311" military rifles usually.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are -
3 Cavity Cramer HP Brass GC or PB - TBD...... it will be less than a 4 cavity but more than a two cavity
6 Cavity Brass solid GC or PB - (80,75 with discount) including shipping, top punch and allen keys
8 cavity aluminum Lee Style solid GC or PB - (80,75 with discount) including shipping, top punch and allen keys
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address (imashooterATgmailDOTcom), mold choice, base style (PB or GC) and number of molds wanted (one to however many).
Some eye CANDY :)
243747
If anyone has any questions I can find out the answer.
It fits the 300 Blackout, 300 Savage and 7.62x39, 7.65 BM and several others if orbited larger besides the normal complement of normal 30 calibers. Offered bullet diameters will be 0.311" and 0.313"..... both will cast out about a half thousandth larger dependent on your alloy of choice.
We will need enough to make Miha's pin requirements. We will run this until we get the number we need (probably 34 HP molds due to current supply conditions) or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.
I am offering these choices: 3 cavity PBHP and 3 cavity GCHP on MiHec's two cavity brass blocks , 6 cavity PB solid and 6 cavity GC solid on MiHec's four cavity brass blocks , 8 cavity PB solid aluminum, 8 cavity GC solid aluminum.
NOTE: THIS BULLET IN 0.311" SIZE WILL NOT FIT WHEN POWDER COATED IN TIGHT THROATED RIFLES. They will fit the larger 0.311" military rifles usually.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are -
3 Cavity Cramer HP Brass GC or PB - TBD...... it will be less than a 4 cavity but more than a two cavity
6 Cavity Brass solid GC or PB - (80,75 with discount) including shipping, top punch and allen keys
8 cavity aluminum Lee Style solid GC or PB - (80,75 with discount) including shipping, top punch and allen keys
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address (imashooterATgmailDOTcom), mold choice, base style (PB or GC) and number of molds wanted (one to however many).
Some eye CANDY :)
243747