CLOSED - 41 MP Mold 413-265-WNFP

[2 dogs]

This is a heavy .41 caliber with all sorts of potential and versatility. Nose to crimp on this big bad boy is .430" so it should be perfect for the Ruger Blackhawks and Redhawks, I will measure my Smith shortly and get on here and edit that one in. As drawn it shows a Large, Medium, and cup Hollowpoints and of course a Solid Pin option. Gas Check and Plain base options as well as 2 or 4 cavity molds will be available. I can remember shooting a similar cast bullet at a rock at a bit over 600 yards with some friends. It is difficult to explain without having had you there to see, but this style shoots flatter, bucks the wind better, and gets there with a serious WHOP than most of the other sixgun calibers we were shooting that windy day.

As always, to sign up, we need your DISGUISED email address like this: sixgunman AT anynet DOT com
We also need to know 2 or 4 cavity, GC or Plain Base preference.
Invoice is via Email and payment is via Pay Pal.
Miha will set the prices when the time comes.
This mold is being run elsewhere so SIGN UP as it will likely close abruptly.

Large HP = - 17 gr. off bullet weight
Med HP = - 10 gr. off bullet weight
Cup HP = - 6 gr. off bullet weight

All pins come with mold. Large, Med, cup and blank pins. You can request a penta pin but I can't say for sure if Miha will include one or not.

https://i.imgur.com/KJcnklf.jpg

2 Cavity GC List

01. mopedmedic AT hotmail DOT com....1 mold (add penta pins)
02. jem10 AT bellsouth DOT net....1 mold with all pins

2 Cavity PB list

01.
02. bradleyk4860 AT gmail DOT com....1 mold
03. bigben1948 AT mchsi DOT com....1 mold

4 Cavity GC List

01. evoevil AT AOL DOT COM.....1 mold
02. spharper AT sbcglobal DOT net....1 mold (add penta pins)
03. dcw038 AT msn DOT com....1 mold
04. mrsparkman AT mrsparkman DOT com....1 mold
05. shutupandjump AT yahoo DOT com....1 mold
06. tomgarcia15 AT yahoo DOT com....1 mold

4 Cavity PB List

01. Schockley AT icloud DOT com....1 mold
02.
03. j_snover AT hotmail DOT com....1 mold

4 cav PB Hitek

01. greg AT watch mans tower DOT comm....1 mold with all pins
02. jason_postman AT yahoo DOT com....1 mold with all pins

[evoevil]

4 cavity, GC All pins .413
evoevil ..... at ....AOL...... dot......COM

[475/480]

4 cavity, GC - all pins and a pinta pin
spharper... at ....sbcglobal.....dot ...net

[DW475]

2 cavity, GC & all pins.
dcw038 at msn dot com

[Lefty SRH]

4 cavity, PB, all the pins
Schockley at icloud dot com

[2 dogs]

Updated 4 molds

[DW475]

Can I change mine to a 4 Cavity mold, GC with all the pins. Thank You!
dcw038 at msn dot com

[silverjay]

Any chance of getting a 4 cavity with 2 PB and 2 GC?

[jem102]

2 cavity, GC, all pins. jem10 at bellsouth dot net

[osteodoc08]

4 cav PB , all pins

t o m g arc ia 15 at yahoooooo dot cooom

[evoevil]

this should bump up to the top ......... we need more

[2 dogs]

Can I change mine to a 4 Cavity mold, GC with all the pins. Thank You!
dcw038 at msn dot com

Got it. Please check my work Sir.

[2 dogs]

Any chance of getting a 4 cavity with 2 PB and 2 GC?

The Cramer style molds wont work that way Sir.

[2 dogs]

Updated 7 molds

[2 dogs]

this should bump up to the top ......... we need more

This mold is being run concurrently on at least one other website that I am aware of. It is already at 15 molds over there so there is 22 in total thus Miha could close this at any time. I would suggest anyone interested not sit on the fence.

[DW475]

I requested to change from the 2 cavity to 4 cavity but it looks like i'm down for both molds. Please ensure i'm down for just the 4 cavity mold.
Thanks.

[alamogunr]

Put me down for one 2 cavity, Plain Base (If possible). If no one else wants a plain base, I'll take a GC if that makes it easier.

alamogunr AT charter DOT net

BTW My S&W 657 cylinder measures 1.780" OAL. I have seen case lengths up to 1.290". Starline, which I prefer, gives a range of 1.275-1.285. This boolit should work in Rugers and Smiths. Should give 1/16" + clearance. Somebody should confirm that.

[alamogunr]

Please disregard previous post. I don't drink or do drugs but I must have been on something when I posted the measurements of the S&W cylinder. This morning I measured the cylinder length of the Ruger .41 Mag Bisley. It measured 1.672". Something had to be off. Ruger cylinders are not shorter than S&W. I re-measured the S&W 657 and got 1.670.

[NYBushBro]

What style GC's are these meant to take? Data on the GC shank would be extremely helpful.

NOTE: I would be interested in a 2-cav GC (w/ all pins) pending availability of GC's.

mopedmedic AT hotmail DOT com

NOTE: I would be using this in a Model 1910 Win .401... (the ORIGINAL "Hammer of Thor")!

(Edit: this resembles the Ideal 410426 with the nose chopped off... what is the OAL of the cavity?)

[2 dogs]

What style GC's are these meant to take? Data on the GC shank would be extremely helpful.

NOTE: I would be interested in a 2-cav GC (w/ all pins) pending availability of GC's.

mopedmedic AT hotmail DOT com

NOTE: I would be using this in a Model 1910 Win .401... (the ORIGINAL "Hammer of Thor")!

(Edit: this resembles the Ideal 410426 with the nose chopped off... what is the OAL of the cavity?)

The Gator 410397 Gas Check will work and the gas check shank is .393"-.394"

The HP cavity dimensions are the intellectual property of the designer.

Let me know know if you want to be on the sign up list.

[NYBushBro]

Count me in for a 2-cav GC w/ ALL pins (NOTE: Miha - PLEASE do PENTA!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!)

Ya' know... Miha does GB's on his website now... so I'm curious why we are still doing these 1-2 YEAR wait times (AKA: 6.5 Swedish CRUISE MISSILE - which NEVER HAPPENED.) What's the deal here? (Texas hold'em - Is Miha "ALL IN" like WE are?)

I'm not a kid... 64 in October. Every day is a 'day of grace'. (Ask 'Junior42' - gone TOO SOON).

[NYBushBro]

PS (for 'newbies'): JUNIOR was THE SKS HOG RIFLE King.... (www.frugaloutdoorsman.com). I do miss his company on this forum.

(Search for LeveRevolution by Larry Gibson and it will give you MEGA-load data - with pressure test graphs).

[2 dogs]

Count me in for a 2-cav GC w/ ALL pins (NOTE: Miha - PLEASE do PENTA!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!)

Ya' know... Miha does GB's on his website now... so I'm curious why we are still doing these 1-2 YEAR wait times (AKA: 6.5 Swedish CRUISE MISSILE - which NEVER HAPPENED.) What's the deal here? (Texas hold'em - Is Miha "ALL IN" like WE are?)

I'm not a kid... 64 in October. Every day is a 'day of grace'. (Ask 'Junior42' - gone TOO SOON).

NYBushBro, I can put you down for a 2 cav GC with all the pins and a note with a request for the penta point, but what shall I use for your disguised email address please?

[NYBushBro]

mopedmedic AT hotmail DOT com

[2 dogs]

Updated with 8 molds.

[NYBushBro]

bttt...

[Onty]

This morning I measured the cylinder length of the Ruger .41 Mag Bisley. It measured 1.672". Something had to be off. Ruger cylinders are not shorter than S&W. I re-measured the S&W 657 and got 1.670.
I am assuming you measured just cylinders' length, without case rim.

OAL of the loaded round; 1.285+.430=1.715

If so, this boolit will be OK for Redhawk, but I am afraid too long for Blackhawk and S&W, almost flash with front face of the cylinder.

Am I missing something?

[alamogunr]

I am assuming you measured just cylinders' length, without case rim.

OAL of the loaded round; 1.285+.430=1.715

If so, this boolit will be OK for Redhawk, but I am afraid too long for Blackhawk and S&W, almost flash with front face of the cylinder.

Am I missing something?

OK! Lets start over. I went back and measured both the S&W 657 and the Ruger Stainless Blackhawk. I will just call each of them 1.672"(the Smith varied .002 when rotated). I then measured a new Starline .41 Mag case. OAL=1.280" Rim=.050"

1.280-.050=1.230"
1.230 +.430=1.660"
Using MAX of 1.285-.050(rim) +.430=1.665"

Even if brass is max length, this boolit should still work although very close. Trimming brass to 1.280, if necessary, would give a little more clearance.

Again, someone should check my thinking on this.

The Lyman Cast Bullet Manual shows 1.280" as the "trim to" length, same as my actual measurement. Starline website has a range of 1.275-1.285.

[alamogunr]

I would feel more comfortable if someone would either point out an error in my last post or confirm its' accuracy. I sometimes can't see the forest for the trees.

Granted there is very little room at the end of the cylinder. Close to max loads must be well crimped or what little clearance there is will disappear and possibly tie up the gun. I'm going to watch it very closely when I get the mold.

[Onty]

I would feel more comfortable if someone would either point out an error in my last post or confirm its' accuracy. I sometimes can't see the forest for the trees.

Granted there is very little room at the end of the cylinder. Close to max loads must be well crimped or what little clearance there is will disappear and possibly tie up the gun. I'm going to watch it very closely when I get the mold.
That is the reason why I even obtained 357 Maximum BH cylinder, hoping to make full length withing frame, and line bored it. Couldn't find smith in Canada to do the job, so I gave up. On top of that, stainless revolvers are the one I prefer for shooting; much less chance for corrosion, and in case I made scratch, couple strokes with adequate abrasive, and it looks like new.

Do not get me wrong, I just love look of blued guns, but the only one I will have (hopefully) is one of those Webley Wilkinson revolvers.

[Minerat]

Just checked my BH 4-5/8" 41mag.

Componets

MP 413265 Hps & solids
starline 41mag brass
Case trim length 1.283"

Loaded
crimp at grove (heavy)
Col 1.710"
Clearance from boolit to front of cylinder when loaded 0.020
19.5gr H110

Measured using RCBS metal calipers.

No problems with boolit jumping crimp in the BH or my Henry Big Boy.

Hope this helps.

[BK7saum]

I would like a 2 cavity PB with all pins.

bradleyk4860 AT gmail DOT com

[Onty]

Just checked my BH 4-5/8" 41mag.

Componets

MP 413265 Hps & solids
starline 41mag brass
Case trim length 1.283"

Loaded
crimp at grove (heavy)
Col 1.710"
Clearance from boolit to front of cylinder when loaded 0.020
19.5gr H110

Measured using RCBS metal calipers.

No problems with boolit jumping crimp in the BH or my Henry Big Boy.

Hope this helps.

My apology for "Johnny come lately", but I would appreciate if you could tell us what is OAL of boolit itself, with GC.

Thanks

[alamogunr]

My apology for "Johnny come lately", but I would appreciate if you could tell us what is OAL of boolit itself, with GC.

Thanks

Site is up to old tricks. Quoted my post in notifying email but quotes Minerat in the post above.

I only used the crimp groove to nose measurement per the OP. I assume that you would have to get OAL from 2 dogs.

[Minerat]

My apology for "Johnny come lately", but I would appreciate if you could tell us what is OAL of boolit itself, with GC.

Thanks

It will depend on what gas check thickness you use.

Mine measures 0.828" with copper gator check installed (416 Hornaday from Blammer) cast with #2 alloy

FYI, as cast no GC length is 0.812"

[2 dogs]

I'm not real clear on how or what you guys are trying to figure out with all that math up there. Let's try this:

We know ahead of the crimp groove on this bullet (NTC) we have .430" and a 41 Mag case is supposed to measure 1.290" so if we add that up we get an overall loaded cartridge length of 1.724"

You have to measure your own brass because while .41 Mag brass is supposed to 1.290" it will vary.

Now, slip an empty case in your cylinder. Measure from the back of your case head to the front of the cylinder. If it is longer than our hypothetical 1.724" this bullet will fit when seated and crimped in the crimp groove.

We also know there are 41 Specials and GNR wildcats and Lever action Carbines and revolvers of different makes. So be sure this one suits your needs. I hope this answers your questions.

[NYBushBro]

bttt....

[Dr-Greg]

Is there any way I could sign on for a 4 cav PB Hitek version of this bullet?

A 6 cav solid Hitek would also be fine.

I'm not sure whether to go with hollow point or solid on this one.

[2 dogs]

Is there any way I could sign on for a 4 cav PB Hitek version of this bullet?

A 6 cav solid Hitek would also be fine.

I'm not sure whether to go with hollow point or solid on this one.

Well Sir, how about you decide and I will list it! I am pretty sure I would get that 4 cavity hollow point because you can still cast the solids if you like.

[Dr-Greg]

Ok please put me down for a 4 cav PB Hitek version with all pins

greg ((att)) watch mans tower ((dott)) comm

[2 dogs]

Ok please put me down for a 4 cav PB Hitek version with all pins

greg ((att)) watch mans tower ((dott)) comm

Ok Boss, got it down. Let give it a shot.

[NYBushBro]

How many sign-ups needed to get this into production? (Including the other site mold tally?)

[2 dogs]

How many sign-ups needed to get this into production? (Including the other site mold tally?)

That is up to Miha.

[NYBushBro]

bttt...

[Lefty SRH]

I have a new 41mag on the way so Im excited to see this one happen!

[Jason_2111]

If it's not too late, I'd love to jump in for (1) 4-cavity Plain Base Hitek (will be powder coating), with all the pins.

jason_postman AT yahoo DOT com.

Just picked up a 1977 blackhawk that looks like it's never been fired, real safe queen. :)

[2 dogs]

updated.

[NYBushBro]

Any updates on the ETA of this???

[2 dogs]

Any updates on the ETA of this???

No ETA yet however, some of these buys take more than a year. Some even longer than that. Patience is key.

[GrumpyBear]

I'm in for one of each please 2 Cavity GC and 2 Cavity PB

grumpybear323 AT gmail.com

[jem102]

I was just checking the status on this one and noticed that I indicated I wanted all pins but that is not listed behind my order. Please make it so.

Thank you sir!

[JSnover]

I'm in for a 4 cavity PB

j_snover AT hotmail DOT com

[2 dogs]

I was just checking the status on this one and noticed that I indicated I wanted all pins but that is not listed behind my order. Please make it so.

Thank you sir!

I am happy to make changes for you guys, but PLEASE include your email address so I don't have to go hunt for it to make your change. It's a time save for me and Thanks!

Anytime the mold is a Cramer style, all the available pins will automatically be included as per the description. Jem102, I went ahead and made your change. Thanks for checking my work.

Thanks for working me on this fellas.

[jem102]

Much appreciated!

[2 dogs]

Much appreciated!

Happy to do it.

[S.B.]

Can I get this without the hollow point and no gas check.

Steve

[S.B.]

I'll do 1 of this in .413 PB two cavity, just as long as it will fit both a S&W and Ruger cylinder?
bigben1948 at mchsi dot com
Steve

[S.B.]

What's going on with this thread, I posted I'd do one of these above and have never been added to the list? Nor, can I delete my first post/question?
Steve

[alamogunr]

[QUOTE=2 dogs;4355251]This is a heavy .41 caliber with all sorts of potential and versatility. Nose to crimp on this big bad boy is .430" so it should be perfect for the Ruger Blackhawks and Redhawks, I will measure my Smith shortly and get on here and edit that one in. As drawn it shows a Large, Medium, and cup Hollowpoints and of course a Solid Pin option. Gas Check and Plain base options as well as 2 or 4 cavity molds will be available. I can remember shooting a similar cast bullet at a rock at a bit over 600 yards with some friends. It is difficult to explain without having had you there to see, but this style shoots flatter, bucks the wind better, and gets there with a serious WHOP than most of the other sixgun calibers we were shooting that windy day.

As always, to sign up, we need your DISGUISED email address like this: sixgunman AT anynet DOT com
We also need to know 2 or 4 cavity, GC or Plain Base preference.
Invoice is via Email and payment is via Pay Pal.
Miha will set the prices when the time comes.
This mold is being run elsewhere so SIGN UP as it will likely close abruptly.

Large HP = - 17 gr. off bullet weight
Med HP = - 10 gr. off bullet weight
Cup HP = - 6 gr. off bullet weight

All pins come with mold. Large, Med, cup and blank pins. You can request a penta pin but I can't say for sure if Miha will include one or not.


The highlighted parts should answer your question(s). Like you, I probably won't use the HP pins but will keep them. I don't know why you can't delete a post. Never tried to.

2 dogs will get around to it. I don't think he lives on here.

[alamogunr]

This is a heavy .41 caliber with all sorts of potential and versatility. Nose to crimp on this big bad boy is .430" so it should be perfect for the Ruger Blackhawks and Redhawks, I will measure my Smith shortly and get on here and edit that one in. As drawn it shows a Large, Medium, and cup Hollowpoints and of course a Solid Pin option. Gas Check and Plain base options as well as 2 or 4 cavity molds will be available. I can remember shooting a similar cast bullet at a rock at a bit over 600 yards with some friends. It is difficult to explain without having had you there to see, but this style shoots flatter, bucks the wind better, and gets there with a serious WHOP than most of the other sixgun calibers we were shooting that windy day.

As always, to sign up, we need your DISGUISED email address like this: sixgunman AT anynet DOT com
We also need to know 2 or 4 cavity, GC or Plain Base preference.
Invoice is via Email and payment is via Pay Pal.
Miha will set the prices when the time comes.
This mold is being run elsewhere so SIGN UP as it will likely close abruptly.

Large HP = - 17 gr. off bullet weight
Med HP = - 10 gr. off bullet weight
Cup HP = - 6 gr. off bullet weight

All pins come with mold. Large, Med, cup and blank pins. You can request a penta pin but I can't say for sure if Miha will include one or not.

The highlighted parts should answer your question(s). Like you, I probably won't use the HP pins but will keep them. I don't know why you can't delete a post. Never tried to.

2 dogs will get around to it. I don't think he lives on here.

[2 dogs]

Can I get this without the hollow point and no gas check.

Steve

You can get a plain base, but all of these molds will come with all the pins to include a flat pin so you can cast solids.

I'll do 1 of this in .413 PB two cavity, just as long as it will fit both a S&W and Ruger cylinder?
bigben1948 at mchsi dot com
Steve

Steve, I will put you down for a mold, however since brass length varies and so does cylinder length read post #36 and you can measure your own sixguns to be sure.

What's going on with this thread, I posted I'd do one of these above and have never been added to the list? Nor, can I delete my first post/question?
Steve

What's going on with this thread is normal. We build up a list of wants and Miha builds the molds. A big spoonful of patience is required as these buys can take quite a long time. As long as 3 years in my experience. I added you to the list, but if you do not wish to make the wait let me know and I will adjust the list to reflect your wishes. Your first question is a common one and thank you for asking. As to deleting posts check with a moderator.

[alamogunr]

Please remove me from this GB. I just found a 2 cavity plain base 41 MP Mold 413-265-WNFP buried under some other .41 molds. Apparently, a previous GB was run and I forgot about it as well as forgot about having the mold. It has never been used.

[S.B.]

When is this suppose to go to the machines? How many orders do you need to make this happen? Are we close?
Steve

[2 dogs]

When is this suppose to go to the machines? How many orders do you need to make this happen? Are we close?
Steve

See the bottom paragraph in post 61.

updated

[NYBushBro]

bttt... C'mon, guys and gals... let's get this one in production this year!

(NOTE: according to alamogunr, Miha already has the cherry is cut - from prior GB? See post 62.)

[2 dogs]

I wonder how the trade policies have impacted our group buys. Certainly there are tariffs now on steel, but I bet that is true of all metals. I wouldn't be surprised if the cost of our molds from overseas goes up....

This is also why I don't post prices at the outset. So hang on and we will all find out in due time.

[NYBushBro]

I wonder how the trade policies have impacted our group buys. Certainly there are tariffs now on steel, but I bet that is true of all metals. I wouldn't be surprised if the cost of our molds from overseas goes up....

This is also why I don't post prices at the outset. So hang on and we will all find out in due time.

My concerns exactly... which was why I wrote Miha a note about this on his website, asking about the very same thing.

It may behoove us to get this one done before the end of the year (while the "status quo" is just that).

Things go south trade-wise... and all bets (and future GB's) may be off. Just MY 2 cents..........

[NYBushBro]

Bttt....

[S.B.]

BTT, please

[chsparkman]

If I'm not too late, 4 cavity, GC - all pins.
Thanks
mrsparkman AT mrsparkman DOT com

[osteodoc08]

Can I please change mine from. pB to a GC please!

[Beagle333]

4 cav GC, all pins please.

shutupandjump at yahoo dot com

[2 dogs]

Can I please change mine from. pB to a GC please!

First, thank you all for your patience, participation, and your courtesy.

Second, I will be happy to make any changes you request but please remember to include your email address so I don't have to go searching for it. Dr. Garcia, please check my work and let me know if you need other.

Third, remember, although he does speak English, it is not Miha's first language so we need to not be crazy confusing about disguising our email address. If you don't get a invoice in your email you ain't going to get a mold! This format will do: castbulletshooter AT snailmail DOT com

If we need further security than that, we will make changes at that time.

Last, I hope you had a fine Christmas and a have a better than ever 2019!!

[S.B.]

First, thank you all for your patience, participation, and your courtesy.

Second, I will be happy to make any changes you request but please remember to include your email address so I don't have to go searching for it. Dr. Garcia, please check my work and let me know if you need other.

Third, remember, although he does speak English, it is not Miha's first language so we need to not be crazy confusing about disguising our email address. If you don't get a invoice in your email you ain't going to get a mold! This format will do: castbulletshooter AT snailmail DOT com

If we need further security than that, we will make changes at that time.

Last, I hope you had a fine Christmas and a have a better than ever 2019!!
Thank you and I hope the same for you?
Steve

[2 dogs]

Good News. This group buy is CLOSED!

[NYBushBro]

Give us a heads-up when PAYPAL requests are being sent out. Thanks!

PS: Any news from Miha on the PENTA-PINS?

[Beagle333]

Man, I'm ready for it. I only have one .41 solid mold and I'm bored of playing with it. https://www.marlinowners.com/forum/images/smilies/new/bebored.gif
A HP mold with different pins will keep me experimenting for a while.:coffeecom

[MiHec]

i need to box them. expect paypals in aprox 2 days

[JSnover]

Sweet! :drinks:

[DW475]

I'm excited for this one!

[MiHec]

Paypals are out!
If you missing one, send me PM

[Lefty SRH]

Im paid up, thanks Honchos

[Dr-Greg]

Just paid. Zipcode 65552

4 cav PB Hitek

01. greg AT watch mans tower DOT comm...

Would like the tracking # whenever you get a chance. Thank you.

[S.B.]

Just payed and would appreciate the tracking number when you have time, please?
Steve

[JSnover]

Paid!

[DW475]

Paid!!

[NYBushBro]

Paid!

[mudygmc]

Wondering if i can still get in for a 4 cavity GC with all pins?

Adam
mudygmc AT yahoo . com

[S.B.]

Has anyone heard from the manufacture yet? I haven't heard anything in some time?
Steve

[Dr-Greg]

Has anyone heard from the manufacture yet? I haven't heard anything in some time?
Steve

I paid on Feb 20th and haven't gotten it yet. I was asking about a tracking number, because I understand sometimes the molds take longer than other shipments (for example, I've already got the other 4 molds I ordered, but this one for some reason is taking longer) No idea why

[BK7saum]

I received mine today in Oklahoma.

[NYBushBro]

So... we're looking at 2 weeks?

I was gettin' a little nervious... :-)

[NYBushBro]

I paid on Feb 20th and haven't gotten it yet. I was asking about a tracking number, because I understand sometimes the molds take longer than other shipments (for example, I've already got the other 4 molds I ordered, but this one for some reason is taking longer) No idea why

A tracking number from a package from SLOVENIA (Int'l. Post) is like looking for teats on a bull... don't hold your breath.

[Dr-Greg]

A tracking number from a package from SLOVENIA (Int'l. Post) is like looking for teats on a bull... don't hold your breath.

I've bought dozens of these from him and more often than not, there is a tracking number. That's why some people provide their zipcodes in these buys, so that they can identify their tracking number when he posts them all at once.

[JSnover]

Post office tried to deliver mine today but I wasn't home. I'll pick it up in the morning.

[S.B.]

Post office tried to deliver mine today but I wasn't home. I'll pick it up in the morning.
Does he ship these with a signature requirement?
Steve

[JSnover]

Does he ship these with a signature requirement?
Steve

Yes he does.

[Lefty SRH]

Mine arrived today!

[S.B.]

Still no mold still nothing from seller? My patients is wearing thin.
Steve

[BK7saum]

I have never had an issue not getting an MP mold. However, the issue is most likely with customs. Be patient a little longer. You will receive your mold, just a little later than you expected.

[Dr-Greg]

Mine finally did come. Some of them just take longer than others due to getting caught up in customs.

[S.B.]

Well. what are the sellers priorities for shipping, no on has ever said? He's had my money for some time.
Steve

[JSnover]

He has a rock-solid reputation and this mold is amazing. You won't be disappointed.

[BK7saum]

Well. what are the sellers priorities for shipping, no on has ever said? He's had my money for some time.
Steve

It is my understanding that he doesn't send out paypal invoices until the molds are boxed and ready to ship. Standard shipping is Slovenia post. Recently he has started offering DHL for an extra cost in order to provide the buyer a tracking number. I have probably 25 MP molds, all came Slovenia post. Most took 2-4 weeks to come across the ocean and through US customs. It is not a quick process. Most folks that dont want to wait order a custom one-off mold through accurate or NOE. They are domestic and arrive quicker. Knowing that it takes a few weeks for the mold to get here is part of the MP group buy no way around it. Dont worry, you'll get the mold, I know you just wanted it sooner than later.

[S.B.]

STILL no mold and no contact by seller???? I believe he's had my money for over a month now.
Steve

[S.B.]

STILL no mold and no contact by seller???? I payed on 2-20-19? Somebody please give me a good contact for this seller?
Steve

[S.B.]

STILL no mold and no contact by seller???? I payed on 2-20-19? Somebody please give me a good contact for this seller? Never mind I just PMed him.
Steve