CLOSED - Mihec 311410 Rerun - .311, .312, .313, or .314 Blackout/other

[DukeInFlorida]

Miha reports: PLEASE CLOSE THIS ONE

This is a re-run of the vastly popular .311" 130 grain boolit perfect for the 300 Blackout. It's been run a couple of previous times, and every time it was a sellout. So, we are doing it again. The 300 Blackout continues to be a popular chambering. It's also an awesome boolit for the M1 Carbine.

This buy will be available with some variations:

2 or 4 cavity, please specify which version you desire
plain base or gas checked, please specify which you desire
Available in hollow point or solid, please specify which you desire
Available as .311", or .314", please specify which you desire


218659 218660
218661
218667 218668 218669
218670
218671
218672

Here are the options:
1) 4 cavity Hollow Point, Plain Base or Gas Checked - Hollow Point set, includes three point types, including a pin set to make solid nose bullets PRICE: 114.75 Euros
2) 2 cavity Hollow Point, Plain Based or Gas Checked - Hollow Point set, includes three point types, including a pin set to make solid nose bullets PRICE: 80.75 Euros
3) 4 cavity Solid, Plain Based or Gas Checked - Solid Bullets ONLY PRICE: 80.75 Euros
4) 2 Cavity Solid, Plain Base or Gas Checked - Solid Bullets ONLY PRICE: 63.75 Euros
5) Can be added to any version of this buy, DHL shipping is an additional $8 (US) Please specify if you desire this shipping method. Otherwise shipments not designated as DHL will ship regular postal service.
6) I need your zip code so that we can provide tracking and shipping confirmation for regular post service shipping. No Charge, need zip code in all listings, please.

These prices are the 15% discounted price.

Add a set of high quality handles to any mold order for only 20 Euros extra, the handles will ship with the molds.

NOTE: Each of these molds can be produced for you in any dropped bullet diameter, including .311", .314". That will allow you to size and load these in a variety of cartridges and rifles. AR/AK, whatever. They are well suited for a number of uses. NO MIXING OF Bullet types or diameters in any mold.

We require 25 molds, total, to proceed with this buy. All prices are quoted in Euros. Miha will issue PayPal invoices in Euros, which when paid, will be paid at the current exchange rate in US Dollars. You do NOT have to use PayPal to pay the invoice. The invoicing system will allow you to use any credit/debit card for paying the invoice. Please provide your preference for number of cavities, plain base or gas checked, and size of bullet, zip code, and whether you want the handles and the DHL shipping method.

If you are building a 300 Blackout, or any gun which would benefit from this boolit, get on the list ASAP. I would expect that this one will go quickly. If any questions, please PM me here.

We'll need the obligatory 25 HP orders as is Miha's need for re-buys on hollow points. It has to do with the minimum purchase he has to make for the pin sets. We are already at 28 Hollow Point orders, plus the three solid nose. When we get to 25 HP's, Miha will close the buy, so this one will likely go quickly!

NOW AVAILABLE WITH ALL MOLD ORDERS - HANDLES! Handles (which fit all MP-Molds), ordered separately, are normally $23 Euros, which includes shipping. If you order any handles with the molds, Miha will reduce the price to $20 Euros, and will ship the handles with the molds. So, this is a great opportunity to get a set of Miha's wonderful handles at a great price. Please advise if you want handles shipped with your mold(s).

Please provide your disguised email address, as Miha will use that when the molds are ready, for invoicing purposes. Include number of cavities, and whether gas checked or plain based, and with or without handles. All prices include shipping. If you order the mold with handles, the handles will invoice at a discounted price (additional 20 Euros), and will ship in the box with the mold.

To assist with providing you tracking and shipment confirmation details, I will also need your ZIP CODE. And, finally, we will offer, for an additional fee of $8 (US) the option to ship your mold(s) via DHL Rapid Delivery. That's three days, door to door. It's an extra fee, but will get your mold(s) to you very fast, even during the upcoming holidays when everything else historically slows to a snails pace. So, if you are in on any of the MP-Molds group buys, please provide your honcho with your zip code, and whether you want the DHL shipping.

Here's the active buy list:

*Four Cavity HP Gas Checked/Plain Based, with all pins indicated - 114.75 Euros. Indicate if adding handles, 20 Euros additional
1) DukeInFlorida - (1) Four Cavity Hollow Point, gas checked, with all pins, .311", with HANDLES and DHL shipping, please - castboolits at sebagosales dot com, 32127 Zip Code
2) grn - (1) Four Cavity Hollow Point, gas checked, with all pins, .311" - garyneb at Comcast dot net, (no handles)
3) ryan - (1) Four Cavity Hollow Point, gas checked, with all pins, .311" - dearborn416 AT yahoo DOT com (no handles)
4) GoodAlloy - (1) Four Cavity Hollow Point, gas checked, with all pins, .314" all pins - Amadaus 101 at outlook dot com (no handles), 43150 Zip Code
5) Ramslammer - (1) Four Cavity Hollow Point, gas checked, with all pins, .314" all pins - namovlov at bigpond dot com (no handles)
6) Jason 2111 - (1) Four Cavity Hollow Point, gas checked, with all pins, .311" - jason_postman at yahoo dot com, (no handles)
7) MstrEddie - (1) Four Cavity Hollow Point, gas checked, with all pins, .311", with HANDLES, - eddymartinez13 at gmail dot com , 33027 zip code
8) Meadmkr - (1) Four Cavity Hollow Point, gas checked, with all pins, .311" - meadmkr at yahoo dot com, 20165 Zip Code (no handles)
9) Rockwell - (1) Four Cavity Hollow Point, gas checked, with all pins, .311" - rockwell5926 at gmail dot com, 82930 zip code (no handles)
10) Thraxx - (1) Four Cavity Hollow Point, gas checked, with all pins, .311" - vfluckey at midco dot net, With DHL Shipping, 57110 Zip Code (no handles)
11) Glockinstein40 - (1) Four Cavity Hollow Point, gas checked, with all pins, .311" - with HANDLES - Glockinstein40 at yahoo dot com, 49286 zip code
12) leetkd - (1) Four-cavity hollow point, gas checked, .311" with all pins, leetkd at gmail dot com, with HANDLES, with DHL, 55024 Zip Code
13) Bagdadjoe - (1) Four-cavity hollow point, gas checked, .311" with all pins, with DHL shipping, miller814452 at bellsouth dot net, 40601 Zip Code (no handles)
14) autodidact - (1) Four Cavity Hollow Point, gas checked, with all pins, .314" - with HANDLES - jbpaul at suddenlink dot net - 71111 zip code
15) autodidact - (1) Four Cavity Hollow Point, plain base, with all pins, .314" - with HANDLES - jbpaul at suddenlink dot net - 71111 zip code
16) .36navy - (1) Four-cavity hollow point, gas checked, .311" with all pins, sgardner106 at gmail dotcom, 67016 Zip Code (no handles)
17) hlvabeach - (1) Four Cavity Hollow Point, plain base, with all pins, .311" - Vtech26 at yahoo dot com, 23451 Zip Code (no handles)
18) shortlegs - (1) Four-cavity hollow point, gas checked, .311" with all pins,, with HANDLES, with DHL shipping - janefike at mindspring dot com 35005 Zip Code
19) fivegunner - (1) Four-cavity hollow point, gas checked, .311" with all pins, fivegunner at sbcglobal dot net , 49331 Zip Code ( no handles )
20) bpatterson - (1) Four-cavity hollow point, gas checked, .311" with all pins, rocpyro at gmail dot com, With Handles
21) evoevil - (1) Four-cavity Hollow Point, gas checked, with all pins, .311"- evoevil at aol dot com (no handles)

*Four Cavity Solid Nose Gas Checked or Plain Based. 80.75 Euros. Indicate if adding handles, 20 Euros additional
1) schemelschelm - (1) Four Cavity, Solid Nosed, gas checked, .311", - vefa01-raps (at) freenet (dot) de. (no handles)
2) kens - (1) four cavity, solid nose, plain base, drop dia. .314" , with HANDLES, kenschott2 at gmail dot com 31324 Zip Code
3) James Wisner - (1) Four Cavity, Solid Nosed, gas checked, .311" diameter, DHL SHIPPING, jwisner at compprime dot com, 98522 Zip Code, (no handles)
4) sutherpride59 - (1) Four Cavity, Solid Nosed, gas checked, .311", Brian dot Allen dot Hancock at gmail dot com, 31548 Zip Code, (no handles)
5) lreed - (1) Four-cavity Solid Nosed, gas checked, .311", lreed39 at yahoo dot com, 42066 Zip Code (no handles)
6) Smk SHoe - (1) 4 cavity Solid Point, gas checked .311", paul dot a dot shoemaker1 at gmail dot com, 28326 Zip Code (no handles)

*Two Cavity HP Gas Checked/Plain Based - 80.75 Euros. Indicate if adding handles, 20 Euros additional

1) Stmtrn - (1) Two Cavity Hollow Point, gas checked, with all pins, .311" size - bbenj1967at gmail dot com 97701 Zip code (no handles)
2) Teemu - (1) Two Cavity Hollow Point, gas checked, with all pins, .314", with HANDLES - paska_10 at hotmail dot com
3) gmfowler2 - (1) Two Cavity Hollow Point, gas checked, with all pins, .311"- gmfowler2 [at] gmail [dot] com 43232 zip code (no handles)
4) Alaskan100 - (1) Two Cavity Hollow Point, gas checked, with all pins, .311" with HANDLES - alaskan100 AT hotmail DOT com 43830 zip code
5) Miko a - (1) Two Cavity Hollow Point, gas checked, with all pins, .311" - miko_a at hotmail dot com, 41339 Zip Code (no handles)
6) georgerkahn - (1) Two Cavity Hollow Point, Gas checked, with all pins, .311" - kahngr at potsdam dot edu, 13676 Zip Code (no handles)
7) jblee10 - (1) Two Cavity Hollow Point, Gas checked, with all pins, .311" - jblee10 at hot mail dot com, 96130 Zip Code
8) KMac - (1) Two Cavity Hollow Point, Gas checked, with all pins, .311", kevmcclain at gmail dot com (no handles) DHL Shipping 75070 zip code

*Two Cavity Solid Nose Gas Checked/Plain Based - 63.75 Euros. Indicate if adding handles, 20 Euros additional
1)
2)

*Handles ONLY, no mold 23 Euros
1)
2)

We have achieved enough mold orders that Miha has declared that this group buy is closed. He's ready to run production!!
I am moving this buy to the CLOSED area. Miha will likely make a few extras, but not many. If you have been on the fence about this buy, get off the fence and join in. Last Call!

[grn]

1- Four Cavity GC Hollow Point with all pins. .311

[schemelschelm]

Price for a 4 cavity solid .311 gas checked?

[bluejay75]

Interested...are the only solid options listed?

[evoevil]

would it work in a 30/30 ?

[Fastleo]

What does this weigh with no hp

[DukeInFlorida]

Handles or no handles? And, I need your disguised email address please


1- Four Cavity GC Hollow Point with all pins. .311

[DukeInFlorida]

95 Euros


Price for a 4 cavity solid .311 gas checked?

Yes, two and four cavity only, you choose gas checked or flat based, and the diameter of the dropped boolit.


Interested...are the only solid options listed?

Yes, the nose should be flat enough to avoid the primer issue


would it work in a 30/30 ?

130 grains in solid


What does this weigh with no hp

[schemelschelm]

95 Euros
Yes, two and four cavity only, you choose gas checked or flat based, and the diameter of the dropped boolit.


Nice!

And is a diameter of .309 as cast possible? If .311 is the smallest, it will be horrific to size down to .309, or?

[Gamsek]

Nice!

And is a diameter of .309 as cast possible? If .311 is the smallest, it will be horrific to size down to .309, or?

I have the same MP 311410 4cav HP and I size it to 0.3095” with no problems. I then powdercoat it to get 0.311” which works best in my 300 BLK. Great boolit, very useful with short and long HP pins!
https://uploads.tapatalk-cdn.com/20180419/bf7e2fb686cd5c2e03ecaddad5ca7635.jpghttps://uploads.tapatalk-cdn.com/20180419/8c7e61334c548c607b832eb24b68c572.jpg

[evoevil]

1- Two Cavity GC Hollow Point with all pins. .311
evoevil ,,,,,AT....aol.....DOT....com
my zip is 20705

[schemelschelm]

Thanks @Gamsek!

Ok, so please put me down for one 2 cavity Hollow Point .311 gas checked + one set of handles.

vefa01-raps (at) freenet (dot) de

[grn]

Handles or no handles? And, I need your disguised email address please

no handles

garyneb at Comcast dot net

[Teemu]

.313 2-cavity HP GC and handles

paska_10 at hotmail dot comm

Thanks

[DukeInFlorida]

I'll presume that you are somewhat new to casting. It's quite common to buy a .311 mold when you want to end up at .309. Easy to do with one pass.


Nice!

And is a diameter of .309 as cast possible? If .311 is the smallest, it will be horrific to size down to .309, or?

[DukeInFlorida]

Updated orders, thanks

[schemelschelm]

Easy to do with one pass.

Great, thanks!

[Law.man]

Just to be clear, is this GB also subject to 15% discount off the listed price?

[ryan]

(1) Four Cavity Hollow Point, gas checked, with all pins, .311" (no handles)
dearborn416 AT yahoo DOT com

Thanks,
Ryan

[gmfowler2]

(1) two cavity hollow point with all pins, gas checked .311 no handles.
gmfowler2 [at] gmail [dot] com

[DukeInFlorida]

Yes, of course




Just to be clear, is this GB also subject to 15% discount off the listed price?

[DukeInFlorida]

Added,
thanks


(1) Four Cavity Hollow Point, gas checked, with all pins, .311" (no handles)
dearborn416 AT yahoo DOT com

Thanks,
Ryan


(1) two cavity hollow point with all pins, gas checked .311 no handles.
gmfowler2 [at] gmail [dot] com

[schemelschelm]

Thanks @Gamsek!

Ok, so please put me down for one 2 cavity Hollow Point .311 gas checked + one set of handles.

vefa01-raps (at) freenet (dot) de

@DukeinFlorida:
Please change my order to a 4 cavity solid, .311 gas checked + 1 set of handles. Thanks!

[GoodAlloy]

Please add me to list for;
4 cavity HP, GC, .314" all pins
Amadaus 101 at outlook dot com

[Law.man]

Yes, of course

Thank you my good sir! In that case I'll have a 4 cavity solid, plain base, .314 and a set of handles.
worgen(dot)wiki(at)gmail(dot)com

[Ramslammer]

G'Day
Could I have a 4 cav hollow point gas check in .314 please?
namovlov at bigpond dot com

[DukeInFlorida]

schemelschelm, your order has been corrected to your specifications, thank you/


@DukeinFlorida:
Please change my order to a 4 cavity solid, .311 gas checked + 1 set of handles. Thanks!

These additional orders have been entered. Thanks.


Please add me to list for;
4 cavity HP, GC, .314" all pins
Amadaus 101 at outlook dot com


Thank you my good sir! In that case I'll have a 4 cavity solid, plain base, .314 and a set of handles.
worgen(dot)wiki(at)gmail(dot)com


G'Day
Could I have a 4 cav hollow point gas check in .314 please?
namovlov at bigpond dot com

[Jason_2111]

(1) Four cavity hollow point, gas checked, all pins, .311 (no handles)
jason_postman AT yahoo.com

Thanks! :)

[schemelschelm]

@DukeinFlorida:
Please change my order to a 4 cavity solid, .311 gas checked + 1 set of handles. Thanks!

Delete the handles please.

[MstrEddy]

Duke, put me in for 1 Hollow Point, gas checked, with all pins, .311", with HANDLES, please - eddymartinez13 at gmail dot com

[DukeInFlorida]

MstrEddy, is that a TWO cavity or FOUR cavity HP mold that you want? You weren't specific enough.


Duke, put me in for 1 Hollow Point, gas checked, with all pins, .311", with HANDLES, please - eddymartinez13 at gmail dot com

[DukeInFlorida]

Waiting for final confirmation from Miha, but effective with all new buys, you will have an option of having Miha ship your molds via DHL for an additional $8 (US) more. Shipping will be 3 days! Once Miha replies back to all honchos with the final details, we will add that option to the buys. IF you want your mold shipped via DHL (with full tracking details), the cost will be an additional $8 US added to your invoice.
219740

Also, we are working on a system whereby even standard Post Office shipments will get tracking details. This will be done via ZIP CODES. Effective immediately, the MP-Molds honchos will require your zip codes, which we will add to your order listing. So, please provide that detail for every active group buy you are part of. Thanks.

[MstrEddy]

Duke,
4 cavity please.

Zip - 33027

[DukeInFlorida]

Yessir! Thanks. DHL? Or, regular Postal delivery?


Duke,
4 cavity please.

Zip - 33027

[MstrEddy]

Duke,
DHL please.

Thanks!

[DukeInFlorida]

Yessir! Perfect. Thanks. You are in.


Duke,
DHL please.

Thanks!

[gmfowler2]

Regular post, 43232

Sent from my SAMSUNG-SM-G900A using Tapatalk

[DukeInFlorida]

I am hoping to reach everyone via this post, but will send PM's to everyone that misses my inquiry here........

Needing to add two additional details to all of my active group buys, so please reply here (or PM if you feel the need)
1) I need your mailing ZIP CODE. We are working on a system whereby future Postal Office shipments will generate tracking details. I'll provide confirmation links at the tail end of each closed Group Buy which will allow you to check on the shipment status, and see where it is. Regular Postal service shipping is included in the cost of the mold.

2) We are now offering DHL rapid shipping (three days door to door) for an additional $8 US, which would be added to your invoice at the time of shipping. Unless you specify DHL shipping, all shipments will go regular Postal Office shipping. Here's the upcoming issue............ As the holidays gets closer, the really really fast postal office shipments that we have recently been enjoying will slow down to a snails pace. We'll all go from celebrating fast deliveries of molds to lamenting that "Aunt Martha's Christmas Cookies" seem to get delivered before your molds do. So, we offer, on all Group Buys from here on in, DHL shipping as an option, for a flat rate of $8 (US) additional. Unless you specify DHL when you give me your order, the mold will ship via regular Postal service, whether it's soon or during the holidays. Seems to me that an additional $8 (US) is a cheap price to assure that the mold gets here quickly by a reputable delivery service, and with tracking details that are pretty solid. So, specify DHL or regular shipment when you place your order.

Now, as I pointed out in 1), your zip code will provide us with a mechanism for providing some tracking details for regular postal service shipments. That will be free, and should be fine for some people.

If you would, therefore, please provide me with your zip code, and whether you prefer DHL shipping for the additional $8 (US).

[Law.man]

ZIP code 60200, standard shipping

[DukeInFlorida]

Thanks, added that detail to your order.


ZIP code 60200, standard shipping

[DukeInFlorida]

Alaskan100 ordered via PM. Added his 2 cav version to the list, thanks.

[Miko_a]

Two Cavity PB Hollow Point with all pins. .311 (no handles)
miko23lof ,,,,,AT....gmail.....DOT....com
my zip is 41339 via regular post

[meadmkr]

Put me done for one...

(1) Four Cavity Hollow Point, gas checked, with all pins, .311" - meadmkr at yahoo dot com, (no handles) zip is 20165

[DukeInFlorida]

I have both orders entered. Thanks.


Two Cavity PB Hollow Point with all pins. .311 (no handles)
miko23lof ,,,,,AT....gmail.....DOT....com
my zip is 41339 via regular post


Put me done for one...

(1) Four Cavity Hollow Point, gas checked, with all pins, .311" - meadmkr at yahoo dot com, (no handles) zip is 20165

[Rockwell]

4 cav HP all GC .311
rockwell 5926 (at) gmail (dot) com
82930

[DukeInFlorida]

Added, thanks.
I am presuming that there isn't really a space between rockwell and 5926, otherwise it would look like rockwell_5926
I removed the space. Hope I have it right.


4 cav HP all GC .311
rockwell 5926 (at) gmail (dot) com
82930

[Rockwell]

That is correct. Thanks.

[Law.man]

Could you take me out of this one? I decided to go heavier for my AK. Thanks

[thraxx]

looks like another good one

(1) Four Cavity Hollow Point, brass, gas checked, with all pins, .311 - vfluckey at midco dot net

[Glockinstein40]

4 cavity gas check hp all pins .311 brass with handles,
Glockinstein40 at yahoo dot com

[DukeInFlorida]

Removed


Could you take me out of this one? I decided to go heavier for my AK. Thanks

Added, thanks. Please supply your zip code so that when the molds get shipped, we can provide some tracking details.


looks like another good one

(1) Four Cavity Hollow Point, brass, gas checked, with all pins, .311 - vfluckey at midco dot net

Added, thanks. Please supply your zip code so that when the molds get shipped, we can provide some tracking details.


4 cavity gas check hp all pins .311 brass with handles,
Glockinstein40 at yahoo dot com

[DukeInFlorida]

Reminder: When you indicate your order, I need all of the details indicated in the opening post, INCLUDING your zip code. That will assist us with providing you with tracking details when the molds ship. We have tested the tracking system, and it works quite well, including showing when it reaches Customs, leaves Customs, etc.... If you want that detail, get me your zip codes.

Also, even if you don't want handles or DHL shipping (you'll be begging for DHL come the holidays), please provide your specific instructions with regard to both those details. It will make my job a little easier.

[thraxx]

Reminder: When you indicate your order, I need all of the details indicated in the opening post, INCLUDING your zip code. That will assist us with providing you with tracking details when the molds ship. We have tested the tracking system, and it works quite well, including showing when it reaches Customs, leaves Customs, etc.... If you want that detail, get me your zip codes.

Also, even if you don't want handles or DHL shipping (you'll be begging for DHL come the holidays), please provide your specific instructions with regard to both those details. It will make my job a little easier.

zip: 57110
no DHL at this time.

sorry i missed the part about the zip code in the original instructions. If this hasn't shipped before the holiday season, I might change to DHL shipping. :D

[leetkd]

(1) Four-cavity hollow point, gas checked, .311" with all pins, leetkd at gmail d0t c0m, with handles, with DHL, zip is 55024

[DukeInFlorida]

Thank you


zip: 57110
no DHL at this time.

sorry i missed the part about the zip code in the original instructions. If this hasn't shipped before the holiday season, I might change to DHL shipping. :D

Added, thanks! Gets us even closer to shipping.


(1) Four-cavity hollow point, gas checked, .311" with all pins, leetkd at gmail d0t c0m, with handles, with DHL, zip is 55024

[Glockinstein40]

Duke , 49286

[Stmtrn]

I ll take a 2 cavity with gas check and hollow point pins. .311 size. Reg shipping B###benj....1967@@@@@gmail......com
Zip 97701

[DukeInFlorida]

Thank you for the detail. It will assist us with getting you tracking details.


Duke , 49286

Thanks, added. BTW, no need to over do the disguising of the email addresses. something like this will suffice, "name at somenetwork dot com". We don't want to make it too confusing when Miha is in the middle of creating invoices to send out your molds. I end up having to fix all of them. Thanks for your understanding.


I ll take a 2 cavity with gas check and hollow point pins. .311 size. Reg shipping B###benj....1967@@@@@gmail......com
Zip 97701

[Bagdadjoe]

(1)Four Cavity HP, gc, with all pins, .311, no handles
miller814452 (at)bellsouthdotnet
zip 40601
Thanks, Joe

DHS shipping

[DukeInFlorida]

Added, thanks, Joe. Could I kindly get your zip code, so we can provide you with tracking details when they all ship?


(1)Four Cavity HP, gc, with all pins, .311, no handles
miller814452 (at)bellsouthdotnet
Thanks, Joe

DHS shipping

[autodidact]

autodidact - (1) Four Cavity Hollow Point, gas checked, with all pins, .314" - with handles - jbpaul at suddenlink dot net - 71111 zip code

autodidact - (1) Four Cavity Hollow Point, plain based, with all pins, .314" - with handles - jbpaul at suddenlink dot net - 71111 zip code

[Bagdadjoe]

Oops....
Zip code is 40601.

[DukeInFlorida]

Added, with the specigfied one mold gas checked, and one mold plain base.


autodidact - (1) Four Cavity Hollow Point, gas checked, with all pins, .314" - with handles - jbpaul at suddenlink dot net - 71111 zip code

autodidact - (1) Four Cavity Hollow Point, plain based, with all pins, .314" - with handles - jbpaul at suddenlink dot net - 71111 zip code

Added the zip code, thanks


Oops....
Zip code is 40601.

[MstrEddy]

Duke,
I'd like to change my order to standard shipping, please.

[kens]

4 cavity, plain base, solid nose, drop dia. .315"

kenschott2 at gmail dot com
zip 31324

OK, I'll take it at .314"
regular shipping

[James Wisner]

Sign me up for a mould in the following.

Solid, 4 cavity, gas check, .311 diameter

No handles, DHL shipping

zip 98522

jwisner at compprime dot com

[DukeInFlorida]

Changed to standard shipping


Duke,
I'd like to change my order to standard shipping, please.

kens, I need your disguised email address and zip code please. See James Wisner listing, just below yours for proper formatting of details I need. I am presuming that you do not want to pay a little extra for two day DHL shipping. Added, but I still need details. thanks
Finally, the two offered diameters are .311" and .314". I am not able to change the original "title of the thread" which indicated other diameters are available. Miha was very clear, when we discussed this that 311 and 314 were able to cover all the US and AK style bullet needs (.314 will size easily to 314, 313, 312, and even 311. The 311 will size easily to .311, .310, .309, and .308). So, unless you have massive heartburn with the ordered entered as .314", that's how it will be made.


4 cavity, plain base, solid nose, drop dia. .315"

Added, thank you.


Sign me up for a mould in the following.

Solid, 4 cavity, gas check, .311 diameter

No handles, DHL shipping

zip 98522

jwisner at compprime dot com

[kens]

my post is updated, see above
Thx

[DukeInFlorida]

Thank you, added those details to your order


my post is updated, see above
Thx

[georgerkahn]

I will be privileged to be added to the list, and purchase:
2) One 2 cavity Hollow Point, Gas Checked - Hollow Point set, in 0.311", includes three point types, including a pin set to make solid nose bullets PRICE: 80.75 Euros
georgerkahn
kahngr at potsdam dot edu
My zip code is 13676

[DukeInFlorida]

Added, thanks


I will be privileged to be added to the list, and purchase:
2) One 2 cavity Hollow Point, Gas Checked - Hollow Point set, in 0.311", includes three point types, including a pin set to make solid nose bullets PRICE: 80.75 Euros
georgerkahn
kahngr at potsdam dot edu
My zip code is 13676

[georgerkahn]

I believe my order is for a GAS CHECK version specified in my post (#70), here above. Copied and acknowledged vis Post #71. However, Mr Murphy (as in Murphy's Law ;) ) changed my request when it was listed in first page orders as: 7) georgerkahn - (1) Two Cavity Hollow Point, PLAIN BASE, with all pins, .311" - kahngr at potsdam dot edu, 13676 Zip Code (no handles)

Kindly, please change things so I will receive the gas checked version I desire?

Thanks much!
geo

[DukeInFlorida]

Per my pm, your comment about solid nose was what was confusing. Normally, a lot of solid nose orders are for plain base molds. So, your order should have just said, " 2 cavity, hollow point, gas checked, all pins, .311"

I have corrected your order. please accept my apology.



I believe my order is for a GAS CHECK version specified in my post (#70), here above. Copied and acknowledged vis Post #71. However, Mr Murphy (as in Murphy's Law ;) ) changed my request when it was listed in first page orders as: 7) georgerkahn - (1) Two Cavity Hollow Point, PLAIN BASE, with all pins, .311" - kahngr at potsdam dot edu, 13676 Zip Code (no handles)

Kindly, please change things so I will receive the gas checked version I desire?

Thanks much!
geo

[georgerkahn]

NO apologies necessary! I so appreciate your honchoing this group buy, and am privileged to be a part of it. In those words of Forrest Gump, "Stuff happens" -- and, again, appreciate your change to "gas check". Communication has proved to not be my strongest of skills... An English teacher I once had professed if there was indeed communication where folks clearly understood each other -- there'd probably have been a lot less wars fought, less busy divorce courts, et cetera...
geo

[lreed]

I would like a four cavity .311-solid-gas checked-no handle mold-regular shipping. My zip is 42066. em- lreed39 at yahoo.com
Thanks lreed

[.36navy]

1 4 cavity HP .311 Gas Checked all pins 67016 sgardner106 at gmail dotcom

[jblee10]

I will take one
2 cavity, hollow point, gas checked, .311 diameter. Standard shipping is fine

jblee10 at hot mail dot com
and the zip code is 96130

[hlvabeach]

I want one. 4 cavity, hollow point, flat/plain base, .311 diameter. Standard shipping is fine

Vtech26 at yahoo dot com

and the zip code is 23451

Sent from my SM-G965U using Tapatalk

[DukeInFlorida]

On my way out, and have only 25 minutes to get ready for the day. I'll add these four new orders as soon as I return later today. Thank you all for the orders. I am expecting Miha will be closing this one soon.

(NOTE: My day was a day at the beach. Beautiful sunshine. I had a tumor removed from my T3 vertibre in 2012, and the doctors said that I would only have a 50-50 chance of being able to walk. Well, I walked 4 miles up the beach (two miles each way), and was dog dead tired when I got back to my umbrella. But, I love proving the doctors wrong. I fell asleep when I got home, and woke up at 06:30 this morning. So, sorry that I didn't get the orders entered until this morning. If you are ever in the Daytona Beach, FL area, let me know, and I'd be happy to meet up. But, on't hang out on Daytona Beach itself. Te Cape Canaveral National Seashore Beach is a much nicer beach, not crowded, and is the ONLY beach I go to when I go. Sadly, not often enough)

[DukeInFlorida]

These four orders have been added. Thank you!


I would like a four cavity .311-solid-gas checked-no handle mold-regular shipping. My zip is 42066. em- lreed39 at yahoo.com
Thanks lreed


1 4 cavity HP .311 Gas Checked all pins 67016 sgardner106 at gmail dotcom


I will take one
2 cavity, hollow point, gas checked, .311 diameter. Standard shipping is fine

jblee10 at hot mail dot com
and the zip code is 96130


I want one. 4 cavity, hollow point, flat/plain base, .311 diameter. Standard shipping is fine

Vtech26 at yahoo dot com

and the zip code is 23451

Sent from my SM-G965U using Tapatalk

[shortlegs]

4 cav hp gc with all pins, handles, dhl shipping please. janefike at mindspring dot com zip 35005

[DukeInFlorida]

With a presumption
1) That you wanted .311" size

Added, thanks.

If I am wrong about the presumption, let me know.


4 cav hp gc with all pins, handles, dhl shipping please. janefike at mindspring dot com zip 35005

[shortlegs]

OOOPS! Yes sir .311

[DukeInFlorida]

Need a couple more hollow point orders to get this one moving to production. Miha needs to buy 100 sets of pins. We're very close!

[fivegunner]

Hi, please put me in for a 4cavity brass HP with all pins GC .311 mold . ( no handles ) fivegunner-at-sbcglobal-dot-net . area code 49331. thanks for running this GB. :D

[DukeInFlorida]

Technically, it's a ZIP code, not an area code. LOL

Added, thanks


Hi, please put me in for a 4cavity brass HP with all pins GC .311 mold . ( no handles ) fivegunner-at-sbcglobal-dot-net . ZIP code 49331. thanks for running this GB. :D

[sutherpride59]

Guesstimating within reason do y’all think these boolits would have a greater accuaracy potential than the Lee 312-155-2r with both being gaschecked?

[DukeInFlorida]

OMG, anything Lee will have lesser accuracy potential than these custom HIGH QUALITY molds.

It takes three basic conditions for success with cast lead bullets (more if you get into deeper fine details, but three basic ones):
A) The right alloy hardness for the velocity of the bullet
B) The right diameter of the bullet, in relationship to the bore diameter
C) The right lube for the velocity and length of barrel

A gas check, quite simply, makes up for slight errors in any of those three. Out of round is something that a gas check isn't going to fix.

1) Lee is notorious for out of round bullets. Running them through a lubricizer will make them round, but they will never be CONCENTRIC. They will wobble in flight.
2) Lee is notorious for having their different cavities drop bullets with different weights. It's the reason some people prefer single cavity molds, so every bullet is exactly the same.

The MP-Molds are made with highly skilled craftsmen, on state of the art machining centers, from the highest quality materials. These brass molds are very dimensionally stable. That's whyb these Group Buys are for custom molds, and not for Lee molds. I personally gave up on Lee molds decades ago, and now ONLY buy and use high quality molds. And, you have a no questions asked guarantee for near perfection.

If you haven't yet, I urge you to read the FREE "bible", written by one of our own, on the subject of casting bullets, how to do it, what's important, how it works and why:

From-Ingot-to-Target-A-Cast-Bullet-Guide-for-Handgunners (http://castboolits.gunloads.com/showthread.php?110212-From-Ingot-to-Target-A-Cast-Bullet-Guide-for-Handgunners)


Guesstimating within reason do y’all think these boolits would have a greater accuaracy potential than the Lee 312-155-2r with both being gaschecked?

[sutherpride59]

(1) Four Cavity, Solid Nosed, gas checked, .311", Brian(dot)Allen(dot)Hancock(AT)gmail(dot)com
(no handles)

[DukeInFlorida]

Yessir! And, thank you... If you provide your Zip Code, Miha will provide tracking details for your mold when it ships.

Just waiting for Miha to close this one...


(1) Four Cavity, Solid Nosed, gas checked, .311", Brian(dot)Allen(dot)Hancock(AT)gmail(dot)com
(no handles)

[DukeInFlorida]

Miha has reported that this buy is closed. He's ready to run production!!

He will likely build a few extras, but not many. If you really want this mold, get in now.
I am moving this thread to the closed area. Really.. if you want in, this is last call!!

[sutherpride59]

Sorry 31548


Yessir! And, thank you... If you provide your Zip Code, Miha will provide tracking details for your mold when it ships.

Just waiting for Miha to close this one...

[DukeInFlorida]

Just a reminder....

Even though this BUY is technically CLOSED, Miha always makes a few extras, and I can add you, even at the last minute, if you need/want this mold. But, don't delay!

[bpatterson84]

If you can still add, I'll take a 4 cavity GC HP at .311.

rocpyro at gmail , com

[bluejay75]

J _ bownes at yahoo dawt comm

8 cavity .311 plain base Lee Style

[Miko_a]

Hi duke,

Having problems with my email (gmail), can i change it to miko_a at hotmail dot com just to be sure i get the invoice from mihec?

Thanks

[KMac]

Two Cavity Hollow Point, gas checked, with all pins, .311"- kevmcclain at gmail dot com (no handles) DHL Shipping 75070

[DukeInFlorida]

Do you have the wrong thread????? No 8 cavs in this one....


J _ bownes at yahoo dawt comm

8 cavity .311 plain base Lee Style

[DukeInFlorida]

Added, hoping Miha adds you to his shipping list. Let me know if you don't get an invoice when he indicates invoices are sent.


If you can still add, I'll take a 4 cavity GC HP at .311.

rocpyro at gmail , com


Hi duke,

Having problems with my email (gmail), can i change it to miko_a at hotmail dot com just to be sure i get the invoice from mihec?

Thanks


Two Cavity Hollow Point, gas checked, with all pins, .311"- kevmcclain at gmail dot com (no handles) DHL Shipping 75070

[bluejay75]

Do you have the wrong thread????? No 8 cavs in this one....

Ask him if he can make it...Thanks.

[Smk SHoe]

Any chance someone cancelled. I just ran across this thread and am interested in the
4 cavity Solid Point, Gas Checked no handles. .311
paul dot a dot shoemaker1 at gmail dot com if possible ( would do plain base if that's only option.). zip 28326

[DukeInFlorida]

IF this had come up during the discussion phase, or even earlier in the active phase, I am sure he could have considered it. But, at this point, he has mold blocks ordered, and dedicated for the listed configurations.
Sorry, but the answer at this time is just NO.


Ask him if he can make it...Thanks.

No one cancelled, but....... Miha does make a few extras on popular molds (this being one), and so I will add you to the list, and hope for the best. Let me know if you do not get an invoice, and I will work the magic another way. Thanks for the order!


Any chance someone cancelled. I just ran across this thread and am interested in the
4 cavity Solid Point, Gas Checked no handles. .311
paul dot a dot shoemaker1 at gmail dot com if possible ( would do plain base if that's only option.). zip 28326

[bluejay75]

There are 2 or 3 molds that will get cut before this one. I asked him directly if he could. If the answers is no. I understand. No need to be a jerk about it.

[DukeInFlorida]

With all due respect and apologies, I think I do a very good job of handling my group buys. I was not trying to be disrespectful in any way. Merely that, at this late hour in the equation, asking Miha to make you one very special version of this mold, when he has already ordered mold blocks............. I think you are asking for almost the impossible.


There are 2 or 3 molds that will get cut before this one. I asked him directly if he could. If the answers is no. I understand. No need to be a jerk about it.

[bluejay75]

No need...

I have asked him if he can make it.

[sutherpride59]

Well sh*t if He were offering 8 cav I would have crapped my pants and handed over $500 bucks for that. I barely have time enough to shoot much less cast and reload. I doubt your request will be granted but if I did I would love to get in on that boolit raining action.

[cwlongshot]

REAL good lookin' bullet!

I'll need to watch for the next run.

CW

[DukeInFlorida]

Keep an eye on this thread. Typically, Miha will announce when they are shipping, and commonly has at least a couple left over that you could jump on.


REAL good lookin' bullet!

I'll need to watch for the next run.

CW

[sutherpride59]

Is it too late to change my mind and request the hollow pointed?

[DukeInFlorida]

At this point, mold blocks and tooling for the production are most likely somewhat set in stone.
This buy has been closed for a while. Trust me, you will like the solid nose version.


Is it too late to change my mind and request the hollow pointed?

[sutherpride59]

Any word on when invoices will be sent? Not impatient just curious.

[DukeInFlorida]

Not directly in terms of the formal schedule.
We do know that Miha suffered a back injury that set him back a few weeks. As you may know, back injuries are the worst to recover from. He's back on the mend, and back making molds. He has been finishing up, packing, and shipping a few of the group buys there were ahead of this one, so we should be at the top of the schedule soon. As always, Miha will announce when PayPals are out.

Please use this time to check your listed order, and make sure all is well. Miha has mold blocks already in house for this one, so we could handle only a couple of additional orders (he always makes a few extras).
Let me know if I have made any errors on your orders, or if you need me to change anything (like add a handle to your order for the savings that comes with that - 20 EUROS instead of the normal 23 EUROS-) Or, if you want me to send the mold(s) with really fast (-like two days!) DHL shipping. As we get closer to the HOLIDAYS (Thanksgiving and Christmas, and New Years), when all US Postal mail gets clogged down, the DHL shipping can get very handy.


Any word on when invoices will be sent? Not impatient just curious.

[evoevil]

Can mine be changed from a 2 cavity HP GC to a 4 cavity HP GC ........ evoevil

[DukeInFlorida]

I will make that request. Let's hope that Miha catches it, and can accommodate your needs.


Can mine be changed from a 2 cavity HP GC to a 4 cavity HP GC ........ evoevil

[evoevil]

I will make that request. Let's hope that Miha catches it, and can accommodate your needs.

Thanks, hope so , But a 2 is better than none ….. LOL.

[GoodAlloy]

Forgot my zip code.
It is 43150
Thanks!

[Bagdadjoe]

Miha is a busy man!!! The best is worth waiting on... :-)

[DukeInFlorida]

YES, he is.... and YES, it IS.......


Miha is a busy man!!! The best is worth waiting on... :-)

[Smk SHoe]

Has this buy been invoiced yet. Just want to make sure I didn't miss anything.

[DukeInFlorida]

No, Miha usually posts in the thread that he has sent PayPal invoices out. I have not yet seen that announcement. So, you haven't missed a thing.


Has this buy been invoiced yet. Just want to make sure I didn't miss anything.

[Miko_a]

Good, thought i missed that also.

[Miko_a]

Hi duke! Any chance i can get handles too? Thought the lee would work

[DukeInFlorida]

NP


Good, thought i missed that also.

The LEE handles WILL work. Sorry if I didn't explain it correctly.
However, you will save on Miha's handles, and get shipping basically free (they will ship with the mold).
And, best of all, they put Lee's handles all to shame!!! I'll add handles to your order. Let me know if that changes.


Hi duke! Any chance i can get handles too? Thought the lee would work

[kens]

Can I get 1 handles with mine also, please?

[DukeInFlorida]

I will add that to your order. Good choice!


Can I get 1 handles with mine also, please?

[Miko_a]

Hi duke! If LEE works.. please don’t add one for me anymore. Got too many handles already. Thanks.

Any idea when they will ship them molds out?

[thraxx]

Duke, would you please add DHL shipping to my order? I'm itching to try this one out. :)

thanks!

[DukeInFlorida]

He's moving down the production list as fast as he can. So, soon, although I can't give you an actual date.
No handles for you! LOL


Hi duke! If LEE works.. please don’t add one for me anymore. Got too many handles already. Thanks.

Any idea when they will ship them molds out?

Added, thanks


Duke, would you please add DHL shipping to my order? I'm itching to try this one out. :)

thanks!

[MiHec]

As we speak I'm machining cavities. Expect paypals next week

[Teemu]

Good news. Thanks [smilie=w:

[Bagdadjoe]

Wonderful...thanks!

[bpatterson84]

I'm #20, could we add handles? If not, it's all good.

[DukeInFlorida]

I'll add that to your order.


I'm #20, could we add handles? If not, it's all good.

[Miko_a]

Duke, i noticed most people got the gas checked version. Going to use it for 300blk, would you recommend gas checked?

[DukeInFlorida]

Yes. Basically, there are three things needed for success with a cast boolit:
1) Hardness of the alloy for the velocity (the faster, the harder. The slower, the softer)
2) Diameter of the boolit for the bore (typically .001" to .002" larger than the bore diameter)
3) Proper lube for the WX and other shooting conditions, as well as barrel length, etc.

What a gas check does is act kind of like a piston ring in your engine. It is a gas seal, and "fixes" slight errors in any of those three factors. So, with Rifle molds, and any special pistol molds, I always specify gas checked.


Duke, i noticed most people got the gas checked version. Going to use it for 300blk, would you recommend gas checked?

[Miko_a]

Thanks duke! Can i get the gas check option on mine also? Or is it too late?

Thanks

[DukeInFlorida]

If he's already machining cavities, it's probably too late. I'll add it, and see what happens.


Thanks duke! Can i get the gas check option on mine also? Or is it too late?

Thanks

[psychodad]

If Miha were to make an extra Two or Four Cavity GC Hollow Point with all pins. .311, I know where he could sell it. hint, hint

[Miko_a]

Thanks duke!

[Miko_a]

Thanks duke!

[MiHec]

PayPals are out!
If you missing one send me PM!

[Teemu]

Paid in. Thanks.

[sutherpride59]

Yay got mine and paid!

[Bagdadjoe]

Paid... ;-)

[Smk SHoe]

Just paid, can't hardly wait. Weather is cooling down, so it's time to cast

[DukeInFlorida]

Don't forget to post images of these castings when you get set up. The "eye candy" always helps when the mold comes up again for re-make.

And, also don't forget.................. Miha always makes a couple extras of these molds. So, if you otherwise feel that you missed out on this or any other mold, please contact Miha directly, and ask for the mold you need. He'll be happy to help.

Thanks to all who ordered.

[KMac]

Paid on 09-28. Forgot to post here about it.

[Bagdadjoe]

Delivery notice from DHL..Friday...I know what I'm doing Saturday. ;-)

[DukeInFlorida]

Yup, mine is also coming FRIDAY. (DHL is kinda like Santa.... he's everywhere all the time! Maybe I should leave cookies and milk?)
And, one of the other nice things about the DHL shipments (in addition to the VERY FAST shipping) is that you can go online (it gave me a link in the confirming email that I got) and fill out a form that will allow DHL to leave the package by your door (or wherever you want it placed) without needing a signature. I have always hated having to be home for post office packages. I won't be here on Friday when it gets delivered. However, I know it will get delivered. And, I also know what I will be doing on Saturday!! I am definitely doing the DHL all the time from now on.

[kens]

paid also,,,,,,

[Stmtrn]

Finally got PayPal to play nice, paid up

[lreed]

Yes!!

[KMac]

DHL sent me a notification that mine would be delivered on Monday.
Yes sir!

[MiHec]

Shipping numbers



Shipping No. Zip Post ISO
RH008864603SI 95037-5223 Morgan Hill, CA US
RH008864625SI 2330 ESPOO,UUSIMAA FI
RH008864648SI 4427 Corinth, ME US
RH008864965SI NY 13676-1 POTSDAM US
RH008865334SI KY 40391-7308 WINCHESTER US
RH008865382SI 20705 Beltsville, MD US
RH008865396SI 23451 Virginia Beach, VA US
RH008865572SI MI 49331 LOWELL US
RH008865586SI 71111 Bossier City, LA US
RH008865609SI 71111 Bossier City, LA US
RH008865612SI 43232 Columbus, OH US
RH008865626SI 67016 Bentley, KS US
RH008865643SI 84302 Brigham City, UT US
RH008865776SI 82930 Bear River, WY US
RH008866034SI 31548-5618 Kingsland, GA US
RH008866065SI 33027 Miramar, FL US
RH008866096SI 28326-7011 Cameron, NC US
RH008866119SI 31324 Richmond Hill, GA US
RH008866167SI TAS 7010 GLENORCHY AU
RH008866215SI 86138 VÄSTERNOR BERGEFORSEN SE
RH008866224SI 7546 GERA DE
RH008881748SI 6776 Kjoelsdalen NO
RH008881751SI 20705 Beltsville, MD US
RH008881765SI 35811 Huntsville, AL US
RH008881779SI 42728-9475 Columbia, KY US
RH008881805SI 42728-9475 Columbia, KY US
RH008881898SI 78620 Dripping Springs, TX US
RH008881924SI 78620 Dripping Springs, TX US
RH008884497SI 98908 Yakima, WA US
RH008884537SI AL 35503 JASPER US
RH008884611SI 26726-8238 Keyser, WV US
RH008884660SI MO 65803 SPRINGFIELD US
RH008884727SI 84489 Burghausen DE
RH008884775SI 31803 Buena Vista, GA US
RH008884846SI 80003 Arvada, CO US
RH008887241SI 33322 Sunrise, FL US
RH008887269SI 29169 West Columbia, SC US
RH008887286SI 29907 Beaufort, SC US
RH008887312SI 65552 Plato, MO US
RH008887326SI 1617 Fredrikstad NO
RH008887343SI ID 83404 IDAHO FALLS US
RH008887365SI 48060 Port Huron, MI US
RH008888635SI 83402 Idaho Falls, ID US
RH008888644SI 83402 Idaho Falls, ID US
RH008888658SI 27540 Holly Springs, NC US
RH008888689SI 80701 Fort Morgan, CO US
RH008888701SI 80701 Fort Morgan, CO US
RH008888715SI 80701 Fort Morgan, CO US
RH008888729SI 51702 NORD BERGNEUSTADT DE
RH008889361SI 71111 Bossier City, LA US
RH008889375SI 71111 Bossier City, LA US
RH008889415SI Michigan 4 Oscoda US
RH008889429SI Michigan 4 Oscoda US
RH008889432SI 27540 Holly Springs, NC US
RH008889463SI NY 13676-1 POTSDAM US
RH008903531SI 52754 Letts, IA US
RH008903576SI 84003 Highland, UT US
RH008903602SI MO 65803 SPRINGFIELD US
RH008903655SI 9131 Chemnitz DE
RH008903681SI 77388 Spring, TX US
RH008905872SI 20165 Sterling, VA US
RH008905957SI 94611 Piedmont, CA US
RH008906042SI 53490 VÄSTRA GÖ VARA SE
RH008906201SI 43566 OHIO WATERVILLE US
RH008936835SI 92141 LYCKSELE SE
RH008936852SI 48093 Warren, MI US
RH008936897SI ARKANSAS 72653 MOUNTAIN HOME US
RH008936923SI 27295 Lexington, NC US
RH008936954SI OH 44705 CANTON US
RH008936971SI OH 44705 CANTON US
RH008944465SI CA 96130-4205 SUSANVILLE US
RH008944540SI 43150 Rushville, OH US
RH008944584SI 49128 MICHIGAN THREE OAKS US
RH008944624SI KY 42066 MAYFIELD US
RH008944712SI CA 93309-3240 BAKERSFIELD US
RH008944805SI 95401 CALIFORNI SANTA ROSA US
RH008944862SI 27540 Holly Springs, NC US

[MiHec]

You can track them here:

https://www.17track.net/en

[Bagdadjoe]

DHL delivered mine this morning...just as beautiful as my other Mihec molds.
Thanks!!

[DukeInFlorida]

I also received mine! Gotta love the fast DHL delivery!!

Here's some eye candy, click on image for full sized:

228333

[shortlegs]

finally figured it out and paid mine

[KMac]

DHL just delivered mine. Threw it together to see what it wold look like. My first MP HP mold so it was a little bit of
an education. Hope I can make some time tomorrow to cast some before I have to go out of town till Saturday.
If It looks like I have it together wrong let me know

228489

[sutherpride59]

Nope looks good Kmac

[KMac]

Thanks Sutherpride59.

[Gamsek]

https://uploads.tapatalk-cdn.com/20181009/65af9ee5b45f3d0b8ff64f40f7b723e1.jpg

Not from this GB but a great photo of 311410 with long pins. After cutting sprue I lightly tap on hinge pin to start open the mould halves then I turn mould upside and finish opening with taps and with handles. They fell off pins immediately. Preheat mould on a hot plate for 20min/I use 380C (2cav) and 390C -400Celzius on my furnace for 4cav.

[Teemu]

I got it yesterday
https://img.aijaa.com/m/00847/14624693.jpg (https://aijaa.com/spvZXV)

Thanks again. Exellent quality as always

[gmfowler2]

Yesterday's mail was better than the normal Tuesday junk. Today's weather was not as exciting. https://uploads.tapatalk-cdn.com/20181010/58a7fb5a9b51be052419ef0ca32b3d35.jpghttps://uploads.tapatalk-cdn.com/20181010/d14a37a963803c286fc96d0b31430bd5.jpg

Sent from my SAMSUNG-SM-G900A using Tapatalk

[Smk SHoe]

Didn't realize these were brass when I ordered. Always wanted to try running a brass mold, now's the chance.

[Smk SHoe]

Maybe the picture of the brass mold is the listing I should have looked at :p.Was way to motivated to order to even look at the specifics. Already was on the list for another mold and have a couple on the shelf that I love already. I am thinking this is what I need, knowing that you can run a brass mold a little hotter than aluminum and I like a extremely fast cadence while casting.

[DukeInFlorida]

The description of the metal used for machining the mold is ALWAYS mentioned by the honchos. You don;t have to look at pictures of previous runs of a mold to determine the metal, typically aluminum or brass. Read the actual paragraph of the mold description for the metal information. Especially when it is a brand new mold design.

Sometimes, the mold maker offers options in the mold metal. For example, one of my other group buys lists the 2 and 4 cavity versions as being brass. However, the 6 cavity version is aluminum only.

Welcome to the wonderful world of MP-Mold's amazing molds. I know you will be happy with it. And, that you will consider additional MP-Mold offerings.

Changing the subject:
If anyone has had difficulty in getting their mold, or tracking delivery information, please let me know. I'll do what I can from here to assist.

[Miko_a]

Very happy with mine duke! Got it tuesday also

[Bagdadjoe]

Say....now that I have my beautiful mold, and I *do* mean beautiful...
What data are you guys using for this boolet in 300BLK?

[sutherpride59]

I love this mold, I cast a beautiful pile of boolits today and this mold rains freaking bullets.

[sutherpride59]

Say....now that I have my beautiful mold, and I *do* mean beautiful...
What data are you guys using for this boolet in 300BLK?

+2 on this

[Smk SHoe]

The description of the metal used for machining the mold is ALWAYS mentioned by the honchos. You don;t have to look at pictures of previous runs of a mold to determine the metal, typically aluminum or brass. Read the actual paragraph of the mold description for the metal information. Especially when it is a brand new mold design.

Sometimes, the mold maker offers options in the mold metal. For example, one of my other group buys lists the 2 and 4 cavity versions as being brass. However, the 6 cavity version is aluminum only.

Welcome to the wonderful world of MP-Mold's amazing molds. I know you will be happy with it. And, that you will consider additional MP-Mold offerings.

Changing the subject:
If anyone has had difficulty in getting their mold, or tracking delivery information, please let me know. I'll do what I can from here to assist.

Please don't think I was complaining. Just didn't know it was a brass mold, kinda surprised when I opened the box. Have two other mold from him and a forth in production hopefully. I have reread the first post and can't find where it says brass.

[Ramslammer]

Mihec
Have sent you a pm

[DukeInFlorida]

Yes, you are correct. No mention (in words) about the molds being brass.
However, a couple of things we should all be aware of:
1) Miha likes to make the Hollow Point molds in brass, so most of the time, that is what they will be.
2) The images from a previous make of the mold is a pretty good indicator (although not 100% perfect) of the nature of the current buy manufacturing.

So, thank you for pointing out my omission. I'll try better in the future to be more precise. I'm hoping that you, and all who purchased this mold are happy.

Thank you again for buying MP-Molds, and allowing me to be one of the honchos.


Please don't think I was complaining. Just didn't know it was a brass mold, kinda surprised when I opened the box. Have two other mold from him and a forth in production hopefully. I have reread the first post and can't find where it says brass.

[DukeInFlorida]

Greets from the States.
Anything I can assist with???

I see your name on the list, and hoping the delivery is going well.


Mihec
Have sent you a pm

[sutherpride59]

Is anybody having feeding issues with these in an AR15? I’m seating them to the crimp groove and my gun does not want to grab that first one for anything, fully loaded or with only 10 in the mag. The gun loads them fine during cycling but that initial loading releasing the bolt via the catch or pulling the charging handle it’s fliping the round up too much in the front and almost seems to be pushing the back down.

[DukeInFlorida]

Sounds less like a boolit issue, and more like a mag or feed ramp issue.

There are TWO overall lengths mentioned in all reloading books:
1) The COAL mentioned on the first page (Title Page) of that cartridge is NOT the length to seat all bullets to. That page shows the MAX length that any cartridge can be, and still feed through the magazine, up and into the feed ramp, into the chamber. Anything longer than that COAL will jam in the process.
2) The OAL mentioned on the page where the specific load data is FOR THAT BULLET is the length that you want to use. That is the one that will give you the pressure results that they tested with that bullet.

Now, I know you said that you seated these to the crimp groove. My suggestion is that you ignore the actual location of the crimp groove. And, seat them to a length that is described in a reloading data book.

The 50th Edition of the Lyman book (my usual first resource for any cast boolit load data) doesn't show any loads for a 1340 grain boolit like this one. However, the OAL for the 160 grain (Lyman mold 311672) is 2.050". And, the OAL for Lyman 311332 is 2.110" (another .005" longer).

The trimmed brass length is 1.368"
The nose of the bullet to the crimp groove is .440"
That adds up a bit SHORT ( quick math = 1.808" ) if you seat them to the crimp groove. You might try seating them longer than you have.

I haven't loaded any of these (or even yet casted any) in 300 Blackout yet, and so haven't tested them. What is your OAL when seated to the crimp groove??

[Gamsek]

I have been playing a lot https://uploads.tapatalk-cdn.com/20181019/1f580d0e1fa26e28c1e5e4a88f9f9424.jpgwith 311410 this year and it feeds fine from my Ruger Ranch 300 BLK magazine if my COL is 1.968” (50mm) or longer. https://uploads.tapatalk-cdn.com/20181019/abc6de05813f505a419e464a4fd0208a.jpg

[DukeInFlorida]

Thanks, Gamsek. That confirms my rough calculations.
In the 300 Blackout, making them close to the 2.000" over all length should work fine. Nothing wrong with assembling them to that length. You do not want to be seating them a lot longer. That would so the seating into the lube groove, which would not be productive.

But, seating them, as 300 Blackouts, into the crimp groove, with a semi-auto rifle, might not work well.

Keep in mind that this is a multi-purpose rifle boolit. The 300 blackout is only one of the uses.
It can also be used as a heavy 30 carbine boolit. Or, a light boolit for any of the normal 30 caliber rifles ( .308 win, 30-30, etc). And, the larger diameters can be used for any of the European rifles (91-30, 303 Brit, etc). Lots of options, but each one requires some adjustment. The bolt actions are easier to work through.

[DukeInFlorida]

Has anyone NOT yet received their mold on this one???

[sutherpride59]

Thanks for the advice y’all I’ll try seating them longer.

[lreed]

Hello; My mold finally arrived today,a four cavity,gas checked, .311dia, solid nosed, very well machined mold! I was beginning to be concerned as there was no "buzz"about the molds only "I got mine". I fired up the furnace and started casting,mold was somewhat slow to heat up,it has much mass, unlike many of my molds this one in on spec for size, weight and the gas check shank is perfect. I cast a couple of hundred,installed gas checks and powder coated. I loaded six dummy rds in .300Blk brass and they cycled from the mag without a hitch,this is the primary rifle I'm hoping to use this bullet in. I have been using Lee 155,however the slightest thing will cause stoppage due to the nose dia being on the brink of too large and I powder coat all bullets. If this 130gr bullet performs as it appears it will,I'll be one happy ole man!! Thanks to all who ramrodded the buy! lreed

[DukeInFlorida]

Welcome to the wonderful world of MP-Molds!!! They are all this amazing!

So that it might help others, could you share what OAL you seated the boolits to?


Hello; My mold finally arrived today,a four cavity,gas checked, .311dia, solid nosed, very well machined mold! I was beginning to be concerned as there was no "buzz"about the molds only "I got mine". I fired up the furnace and started casting,mold was somewhat slow to heat up,it has much mass, unlike many of my molds this one in on spec for size, weight and the gas check shank is perfect. I cast a couple of hundred,installed gas checks and powder coated. I loaded six dummy rds in .300Blk brass and they cycled from the mag without a hitch,this is the primary rifle I'm hoping to use this bullet in. I have been using Lee 155,however the slightest thing will cause stoppage due to the nose dia being on the brink of too large and I powder coat all bullets. If this 130gr bullet performs as it appears it will,I'll be one happy ole man!! Thanks to all who ramrodded the buy! lreed

[lreed]

Hello: Yes,gladly share any info that might help! Standard disclaimer - this is what works in my firearm,maybe not yours, the O.A.L. that I used is 1.90,somewhat short by the Lee loading info but has worked fine in my Anderson Am15 .300Blk. I used H110 starting data from Lee for a 140 jacketed bullet. I have not checked velocity yet,only fired fifty rnds for funct check. Always a work in progress! Lreed

[gmfowler2]

I loaded 25 rounds with a starting load of 17 gr. IMR4227 in 30 Herrett. Of course I wind up with a short throat barrel on my Contender. 2.055" oalhttps://uploads.tapatalk-cdn.com/20181101/3fa2a058caed4919e6140cdaeb0e5d4b.jpg

Sent from my SAMSUNG-SM-G900A using Tapatalk

[eagleotto]

Somehow I missed this run. Is there any expectation of another re-run?
Thank you.

[DukeInFlorida]

Miha usually makes a few extras. Check with him, you MIGHT be in luck.


Somehow I missed this run. Is there any expectation of another re-run?
Thank you.

[eagleotto]

Thanks DukeinFlorida. I PMed him. We will see. It appeared there was a line for extras so I will not hold my breath. I am sure another group buy will happen for this one soon enough, even if I have to start it myself :?

[sutherpride59]

If that happens update this thread with the info please. I deeply regret not getting the HP version of this great mold.

[eagleotto]

I will wait for a reply from Mihec. Sutherpride59, did you ask if any extras existed? If none exist, I may wait a few weeks and restart a discussion to see if there is still enough interest. I look forward to seeing pictures from those that got them!

[DukeInFlorida]

The problem with starting a new discussion is that you will often find that MOST people who wanted one of these molds already got one. It will take a LONG time to go around again, and have enough people who add their names. I've seen second go arounds take over a year. The current rules for discussion is that any discussion that doesn't get enough "traction" in 90 days gets pulled from the discussion phase. I've already had a few drop out of the discussions for that reason.

It's best to be checking the discussions as well as the active areas for molds.

[eagleotto]

Well,
If it is gonna take a while might as well get it going :?

[eagleotto]

Moderators: If this is in the wrong spot please move it or let me know so I can. Thanks.
I have a question for those of you using this mold as a plain base:
Has anyone tried Plain base gas checks on one of these boolits?
Thanks for the feedback.

[Youngtimer]

If this would run again I would be in for 1 for sure, possibly 2

[Teknikal]

The problem with starting a new discussion is that you will often find that MOST people who wanted one of these molds already got one. It will take a LONG time to go around again, and have enough people who add their names. I've seen second go arounds take over a year. The current rules for discussion is that any discussion that doesn't get enough "traction" in 90 days gets pulled from the discussion phase. I've already had a few drop out of the discussions for that reason.

It's best to be checking the discussions as well as the active areas for molds.Does this mold work well for the ar platform? I missed out on this run.

Sent from my SM-G960U using Tapatalk

[DukeInFlorida]

Yes, and has been suggested to others, contact Miha directly, and see if he made a few extras. You might be able to get one.


Does this mold work well for the ar platform? I missed out on this run.

Sent from my SM-G960U using Tapatalk

[Teknikal]

Yes, and has been suggested to others, contact Miha directly, and see if he made a few extras. You might be able to get one.What is the best way to Contact him? on here or email

Sent from my SM-G960U using Tapatalk

[DukeInFlorida]

I would suggest BOTH. One way or the other (or both) he will get the request.


What is the best way to Contact him? on here or email

Sent from my SM-G960U using Tapatalk

[eagleotto]

I contacted him and was able to get one. It arrived today. This is my 6th mold from him and it never gets old gazing on the new ones. Time to take some pics then wash and heat cycle. Do contact him.

[eagleotto]

Has anyone working on 300 Blk with this gotten any results they care to share? I am hoping to get some cast this weekend and start load development after a little aging. I would appreciate any updates.
Thanks.
Do I need to I can start a new thread for this question?

[DukeInFlorida]

I would suggest casting with straight wheel weight alloy. Anything else would be too soft. You can also "water drop" the wheel weight castings to speed up the "age hardening".
There are posts in this thread regarding the overall length to assemble them to. I suggest that you carefully learn from those posts.


Has anyone working on 300 Blk with this gotten any results they care to share? I am hoping to get some cast this weekend and start load development after a little aging. I would appreciate any updates.
Thanks.
Do I need to I can start a new thread for this question?

[eagleotto]

Thanks DukeInFlorida,
I have been reading all that I can find on this mold with 300 blk. I do plan on powder coating and gas checking.
I have seen very little range tests and accuracy reports and was hoping someone has found some usable loads.
Thanks again to you and everyone else.

[Gamsek]

Thanks DukeInFlorida,
I have been reading all that I can find on this mold with 300 blk. I do plan on powder coating and gas checking.
I have seen very little range tests and accuracy reports and was hoping someone has found some usable loads.
Thanks again to you and everyone else.https://r.tapatalk.com/shareLink?url=http%3A%2F%2Fcastboolits%2Egunloads% 2Ecom%2Fshowthread%2Ephp%3Ft%3D374793&share_tid=374793&share_fid=9688&share_type=t

Mostly subsonic but you will see you can use very soft lead with GC. Accuracy was nice. Very versatile light varmint/roe deer bullet


Poslano z mojega LM-X210 z uporabo Tapatalk

[eagleotto]

Thank Gamsek, you are the only one I have really seen post much with this combination, at least that I could find. I do plan to shoot supersonic though. I may make a separate thread for this topic. I hope the weather in Al works out this weekend so I can try this out!

[Gamsek]

Thank Gamsek, you are the only one I have really seen post much with this combination, at least that I could find. I do plan to shoot supersonic though. I may make a separate thread for this topic. I hope the weather in Al works out this weekend so I can try this out!

Keep us posted! I too plan to move into supersonic area this summer with N120 and D060, I will use pure lead with 5%tin and copper GC, short pin. Will try to hunt with those.

[DukeInFlorida]

Powder coating isn't as successful as epoxy coating (Hi Tek). However, either type of coating will not benefit from the use of a gas check. To gas check either a powder coated or Hi Tek epoxy coated bullet would require installing the gas check first, and then applying the coating over the gas check. Counter productive in my book.

Basically, the gas check provides somewhat of a piston ring action. It serves to provide some error correction for alloy hardness, sizing, and lube. That's all negated when you coat a bullet. The coating provides the lube, slight oversizing, and fixes any issue with hardness of the alloy.

You might benefit from reading the areas relating to alloy hardness, sizing, lube, and gas checks in Glenn Fryxell's Book, "From Ingot to Target, A Cast Bullet Guide for Handgunners"
It's free, and here: http://castboolits.gunloads.com/showthread.php?110212-From-Ingot-to-Target-A-Cast-Bullet-Guide-for-Handgunners

Glenn might want to update that book with details on coatings, such as powder coatings and epoxy coatings.

In my own tests with both coatings, the powder coats were too hard and crispy, causing bullets to strip the coatings while using an inertia bullet puller to remove the bullets from crimped cases. While the two part epoxy coated bullets (Hi Tek) allowed the coating to remain firmly on the bullet through the inertia bullet pulling process. The difference didn't appear through the normal test, smashing with a hammer. Hammering isn't part of the normal firing process, while the inertia bullet pulling simulates firing theb bullets from a cartridge. So, in my humble opinion, if you are going to coat a bullet, the Hi Tek epoxy coating is the only one to use, and can be done at home. But using a coating negates the need to use a gas check, even on rifle bullets. I prefer the old method of using a proper bees wax type lube on properly alloyed and sized cast bullets, with a gas check installed. No coatings for me.

[Gamsek]

The best simulation of shooting a polyester coated (powder coated) cast bullet is to - actually shoot it.

PC before GC or GC/size before PC - they both work. Use good (Eastwood, Smoke4320’s powders) that gives you smooth thin polyester coating and follow instructions how to apply, bake. Size accordingly to what works best, for my 311410 and R.Ranch it was 0.311”.

Maybe they don’t survive pulling them out of case, but my coated 311410 definitely survived 16” of Ruger’s Ranch barrel and 12” of wet paper.
https://uploads.tapatalk-cdn.com/20190227/7d65b6421cc5bfc6010f8ef1f759d79b.jpg

[eagleotto]

DukeInFlorida,
Those are good reads indeed. Read them a while ago along with all of the LASC articles. I almost pursued a minor in Materials Engineering because of it. I have tried Hi-Tek along with several powder coats, I like Smoke420's PC. I have some expanded 9mm from another MP mold that have retained all of the coating (like Gamsek's 311410s). I plan on trying this 311410 with and without gas checks. I think the gas check may help in catching the rifling. We will see if there are any differences. It would be neat if this mold had PB and GC bases in the same mold.

[DukeInFlorida]

Would be too expensive to make that way.


DukeInFlorida,
It would be neat if this mold had PB and GC bases in the same mold.

[thraxx]

I would think you could have someone mill out the GC on a couple of cavities.

[Gamsek]

I plan on trying this 311410 with and without gas checks. I think the gas check may help in catching the rifling. We will see if there are any differences. It would be neat if this mold had PB and GC bases in the same mold.

Try without GC, I got decent groups (no load development, no ladder test...) at 80m with 4.5grs of TrailBoss without GC sized at .311”https://uploads.tapatalk-cdn.com/20190228/e6ee76c86b50289bc0e46891ca9b049c.jpg same day, same 4.5grs, same bullet with GC sized to 0.3095”, groups were 2x larger.
https://uploads.tapatalk-cdn.com/20190228/2c6805f2de245407704da338d3159cc8.jpg
Exactly this one, deep HP, subsonic into wet paper, pure lead with 5% tin

[eagleotto]

Would be too expensive to make that way.

I am aware, just would be neat. I have watched Mihec's videos and realize it would not work well. Would be very time consuming.
Gamsek, I am considering having one gc shank cut out. That would still leave 3 gc. If it shoots well I could always get another done.
Also, your really making me want to get a TC barrel or bolt action for the 300 with those sub loads.

[eagleotto]

Got a chance to cast some yesterday and sorted them today. I went with one solid pin, two med. hp pins, and one deep pin. Powder coated a small batch then added a few gas checks afterwards. Those went on easily over the powdercoat. The upper right hand bag are lee 150 fn.
237245

[eagleotto]

For the powder coat, I use the piglet method of dry tumble with airsoft bbs. My PC is from smoke420. Here it is on one of these boolits after being pulled. 237247
And also on some expanded mihec 9mm:
237248
I plan on ordering more of his colors to test.

[eagleotto]

In order to not take up anymore space on this thread, I am starting a new one for this boolit specifically with 300 BLK.
Can anyone comment if this should be done in group buy results, or one of the load subforums?

Thank you

[DukeInFlorida]

I would suggest creating a new thread in the casting area, and then coming back to your post here, and providing a link to the new discussion.


In order to not take up anymore space on this thread, I am starting a new one for this boolit specifically with 300 BLK.
Can anyone comment if this should be done in group buy results, or one of the load subforums?

Thank you