Looking for a .41 wadcutter?

[arlon]

I'd like to find a a .41 wadcutter mold. DEWC or button nose, prefer DEWC. Does anyone still make such a mold? I want one to shoot paper with my Redhawk and some hard cast for my S&W 58 that is a hiking carry gun. I think the defense potential of a full wad cutter is way under estimated.

What would really be nice is to find something extra heavy like a "pin buster" bullet..

[runfiverun]

http://accuratemolds.com/img/bullets/detail/41-220Z-D.png

[Walla2]

Did you look at LBT?

[JonB_in_Glencoe]

There isn't many 41 WC molds out there, I opted for an Accurate Button Nose design, that was already in Accurate's catalog.

http://i640.photobucket.com/albums/uu127/JonB_in_Glencoe/100_1383.jpg (http://s640.photobucket.com/user/JonB_in_Glencoe/media/100_1383.jpg.html)

http://i640.photobucket.com/albums/uu127/JonB_in_Glencoe/rightsidecastpicsubmission1-13-12.jpg (http://s640.photobucket.com/user/JonB_in_Glencoe/media/rightsidecastpicsubmission1-13-12.jpg.html)

[runfiverun]

Tom's button nose is a semi close copy of the Lyman boolit.

I'm too lazy to go look at the number on the side of my mold right now but it's basically a blown up 358091

the one I show is a pin buster mold, it's reversible, and can be gas checked.

[arlon]

Who makes the pin buster mold?

[runfiverun]

it's also an Accurate design.

[bdicki]

https://www.mp-molds.com/e-shop/molds/hb-molds/mp-411-hb-wc-2-cav

[dbarry1]

Nice mold & ruger JonB.

[Thekid]

I found my lee 410-208wc mold on eBay... but I haven't seen another since.... 193068

[too many things]

there is one listed now on feebay

[gwpercle]

NOE 413 - 215 - WC - PB , nice 41 wadcutter , 215 grain can be had with hollow point options, Just checked the NOE store and they are all in stock ready to ship if you want one.
I ordered one, have been fondling it , after newness wears off I might mess it up casting with it.
This design in 38/357 ( the discontinued Lyman #358432 - 160 grain) is a tack driver, I've seen them refered to as a type III wadcutter design, I'm not sure what that is but in 38 in the 160 grain weight it's more accurate than a normal 148 WC. With a hollow point this would be a heck of a " man stopper"
This mould will be used for the Model 58 in my avatar. Two model 58 owners....we have a MODEL 58 CLUB !
Gary

[Paul D. Heppner]

I have two. One is a hollow base and the other I small round button nose. Both are Lyman moulds. Might be interested in selling them once I find them and get the numbers off them.

[arlon]

there is one listed now on feebay
Someone must have grabbed it or I just couldn't find it.. )-:]

[arlon]

NOE 413 - 215 - WC - PB , nice 41 wadcutter , 215 grain can be had with hollow point options, Just checked the NOE store and they are all in stock ready to ship if you want one.
I ordered one, have been fondling it , after newness wears off I might mess it up casting with it.
This design in 38/357 ( the discontinued Lyman #358432 - 160 grain) is a tack driver, I've seen them refered to as a type III wadcutter design, I'm not sure what that is but in 38 in the 160 grain weight it's more accurate than a normal 148 WC. With a hollow point this would be a heck of a " man stopper"
This mould will be used for the Model 58 in my avatar. Two model 58 owners....we have a MODEL 58 CLUB !
Gary

We could never get anything done in this club. We need a third!
Really like the model 58. Have had a few 57s come and go but just won't get rid of the 58. It'a tool..

[pauly]

G'day from Downunder . [smilie=s:

G'day Mate , I have a 5 cavity Lee full waddcutter mold if you still need one I have never used it I think it is new or as good as , if you need it contact me at paulbertram@live.com.au

Regards Paul . :smile:

P.S. I have an RCBS semi waddcutter as well that is set up for a magnacaster but has a manual sprue plate setup by tom at accurate on it now.

[gwpercle]

We could never get anything done in this club. We need a third!
Really like the model 58. Have had a few 57s come and go but just won't get rid of the 58. It'a tool..

LIKE....why don't we have a like button ?

I agree about the model 58, just something about it that is just right , it's my pet big bore.
I jokingly told my wife that when I pass , tuck it in the box with me because I am taking it with me ! The Good Lord is probably a revolver man too !
Gary

[arlon]

LIKE....why don't we have a like button ?

I agree about the model 58, just something about it that is just right , it's my pet big bore.
I jokingly told my wife that when I pass , tuck it in the box with me because I am taking it with me ! The Good Lord is probably a revolver man too !
Gary

Two of my favorite S&W revolvers are the 58 and 13.. They are both surprisingly accurate. I'm just a fan of the fixed sight guns for some dumb reason. Have a few 1917s and MPs to go with them but the 58 is still at the top of the list. If I could ever only have one revolver, it might boil down to the 58. It may well be the best tool in the shed.

[arlon]

G'day from Downunder . [smilie=s:

G'day Mate , I have a 5 cavity Lee full waddcutter mold if you still need one I have never used it I think it is new or as good as , if you need it contact me at paulbertram@live.com.au

Regards Paul . :smile:

P.S. I have an RCBS semi waddcutter as well that is set up for a magnacaster but has a manual sprue plate setup by tom at accurate on it now.

Email sent!