DUKE NUKEM
05-11-2012, 06:42 AM
NOE Copy of RCBS 82054 bullet mould .45-500-FN for 45-70 .460-461" diameter
This is for the 45-70 Winchester 1886 and Marlin 1895.
https://shop.rcbs.com/WebConnect/MainServlet?storeId=webconnect&catalogId=webconnect&langId=en_US&action=ProductDisplay&screenlabel=index&productId=3343&route=C12J059
http://i921.photobucket.com/albums/ad54/LEVERACTIONSHOOTERS/82054.jpg
Seems as though the RCBS mould drops small
It is close to being right but in my experience it is hard to get an RCBS mold the right diameter, most are under size. Mine drops .429" as does my 245 RCBS. It is a matter of luck to get a mold cut with a new cherry. Same as my 500 gr RCBS BPCR boolit that dropped at .457".
We use .431" in the .44.
But then you should show us what the boolit does by posting some pictures. That is the best way for a new fella to make a decision.
We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.
Prices will be as follows:
Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $10.00 Shipping/Handling.
Prices are subject to change at any time.
You can mix number of cavities in an order to make 15.
We will offer gas check or plain base on this bullet.
Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.
Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.
We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal account:
pbsco1@qwestoffice.net
Make checks and money orders out to:
NOE Bullet Moulds
Our mailing address is:
NOE Bullet Moulds
1645 W 150 N
Provo, Utah 84601
801 377-7289
Thank you for your interest in this buy.
Swede Nelson
This is for the 45-70 Winchester 1886 and Marlin 1895.
https://shop.rcbs.com/WebConnect/MainServlet?storeId=webconnect&catalogId=webconnect&langId=en_US&action=ProductDisplay&screenlabel=index&productId=3343&route=C12J059
http://i921.photobucket.com/albums/ad54/LEVERACTIONSHOOTERS/82054.jpg
Seems as though the RCBS mould drops small
It is close to being right but in my experience it is hard to get an RCBS mold the right diameter, most are under size. Mine drops .429" as does my 245 RCBS. It is a matter of luck to get a mold cut with a new cherry. Same as my 500 gr RCBS BPCR boolit that dropped at .457".
We use .431" in the .44.
But then you should show us what the boolit does by posting some pictures. That is the best way for a new fella to make a decision.
We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.
Prices will be as follows:
Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $10.00 Shipping/Handling.
Prices are subject to change at any time.
You can mix number of cavities in an order to make 15.
We will offer gas check or plain base on this bullet.
Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.
Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.
We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal account:
pbsco1@qwestoffice.net
Make checks and money orders out to:
NOE Bullet Moulds
Our mailing address is:
NOE Bullet Moulds
1645 W 150 N
Provo, Utah 84601
801 377-7289
Thank you for your interest in this buy.
Swede Nelson