View Full Version : Intrest in NOE 453 230 RN Re-Run?
04-02-2012, 06:18 PM
I would like one of these molds anyone else?
04-02-2012, 06:26 PM
04-02-2012, 06:55 PM
2 down, 3 to get on the schedule
04-02-2012, 08:36 PM
I would take one.
04-03-2012, 02:23 PM
I will take 2, so that really leaves 1 to get this started
04-03-2012, 06:05 PM
I'm in for one, too. So I guess we're good to get put on the schedule.
04-17-2012, 03:45 AM
04-17-2012, 03:55 AM
Any other details like umber of cavities? Aluminum or brass? Cost?
04-17-2012, 07:39 AM
I would say the standard NOE options and costs for this mold. As for aluminum or brass that depends on the consensus here.
04-17-2012, 07:57 AM
I'm in. Would prefer a brass mold, but can deal with aluminum if that is the concensus of those interested. 5 cavity would be great
04-17-2012, 08:23 AM
My preference would be for a 5 cavity aluminum mould but I could use a brass 4 cavity if that is what the group decides on.
04-17-2012, 08:57 AM
I'm in for 1 of the 5-cav aluminum moulds if you get this going... Have 2 from the last GB but would like a back-up mould just 'because'
04-17-2012, 10:33 AM
Brass would be cool, but aluminum would be more practical
04-19-2012, 08:07 AM
I would be interested. I need this bullet for my kimber. Any idea how far out we are before production? Little short on funds and will have to try and get it together between now and then.
04-19-2012, 10:30 AM
Looking at the noe schedule which we are not officially on yet, it would most likely be a year before this mold was made.
04-19-2012, 11:42 AM
Okay, Thanks. Go ahead and put me on the list. I would like to have one of the brass molds.
04-24-2012, 10:26 PM
I figured I would put the Aluminum V. Brass mold block question up for a vote, If there is 5 or more on each side both could be done it would require a separate spot on the schedule
04-25-2012, 07:07 AM
We have the tooling for aluminum so 5 orders will get it going.
But brass will take new tooling so it would take 15 orders to get it going.
04-25-2012, 07:41 AM
I voted for aluminum in the hopes that this could be done faster. If we get close on the numbers for brass, I'd rather have brass
04-25-2012, 01:32 PM
It seems like we have plenty of intrest for AL mold blocks, I will leave the discussion open for a few more days, though I feel that it will be much easier to get on the schedule for 5+ molds rather than the 15 for brass to cover the tooling. For those of you who wanted brass, is AL deal breaker? If so let me know so Ivan get an accurate count.
04-27-2012, 12:48 AM
Is this the mould that is a clone of the H&G #34? If so I would be interested, but only in a 4 cavity BRASS mould. I already have a 5 cavity aluminum mould that works great, but would love to get this boolit in a brass mould. If it's a different boolit, can you post a drawing or picture of it?
04-27-2012, 04:36 PM
It's not the h&g 34
05-07-2012, 08:57 AM
Any status updates? Are we on NOE's schedule?
10-27-2012, 01:20 PM
Powered by vBulletin® Version 4.2.1 Copyright © 2013 vBulletin Solutions, Inc. All rights reserved.