Mihec 429244 Cramer HP

[sffar]

This buy is For a MiHec edition of the classic Lyman/Thompson 429244 HP


http://castboolits.gunloads.com/imagehosting/184884f2715e4ab3f3.jpg ('http://castboolits.gunloads.com/vbimghost.php?do=displayimg&imgid=3682')


.389" crimp to meplat. Ready to load weights of 1) small HP 249 gr. 2) large HP 241 gr. 3) solid 259 gr.

HP Price:
$120/4C + $16 additional pins + $20 shipping
Solid Price:
$90/4C + $20 shipping

Options and details . .
1. Mold will be four cavity brass (a two cavity can also be cut if there's enough interest. If you're interested in a two cavity make a post saying so and I'll assemble a list. Two cavity pricing would be $90/HP and $70 solid. Fifteen minimum.)
2. Available in .432 and .434 diameters (WW). No mixing cavities.
3. If you prefer a solid, that's also available. No mixing of cavities, though.
4. HP molds come with one set of round pins. Additional pin sets are $16. Blank pins–pins you form yourself–also $16. Lastly "plug pins,"–$16–are available to cast solids if you want to avoid the hollow point pins projecting from the bottom of the mold when reversed.

Please include your (disguised) email address with your request. Miha will send out invoices about the time the buy gets closed. Payment's through PayPal (he's in Slovenia). Shipping's direct.

Discussion thread . .
http://castboolits.gunloads.com/showthread.php?t=134318

Sam

[Grandpas50AE]

I'll respond...2 of the following order: 4C Cramer HP with small HP pins, set of pins for penta HP and set for "plug" (solid point), set of handles. According to my calculation, that will run $120, plus $32 for the extra pin sets, plus $20 shipping, plus the handles (let me know the price), times 2. I believe there is a discount on the shipping for two at the same time, so not sure total exact price, I guess Miha will let me know on the final invoice. These are, of course, brass molds.

g50randerson at hotmail dot com

[sffar]

4C . .
1. Grandpas50AE .432 w/large round and plug pins, handles g50randerson at hotmail dot com
2. Grandpas50AE .432 w/large round and plug pins, handles g50randerson at hotmail dot com
3. sffar .432 w/penta and plug pins cheeseburgerfriesandshake at yahoo dot com
4. Dutch4122 .434 w/plug pins dutch4122(at)yahoo(dot)com
5. x101airborne .432 w/penta pins x101airborne at yahoo dot com
6. midnight .432 w/large round and plug pins rwhyte@widotrrdotcom
7. simonjester76 .432 w/penta, large round and plug pins n3efo AT comcast DOT net
8. Beau Cassidy .432 w/plug pins Smallmouth dot catcher at y.a.h.oo.com
9. 2 dogs .432 HP fcgarza0640 AT hotmail DOT com
10. gunsbrad .434 w/plug pins bradhurt2 at yahoo dot com
11. frankenfab .432 solid fdombek at phillipscorp dot com
12. BRobertson .432 solid w/handles akstormy at kpunet dot net
13. doctorggg .432 w/large round and plug pins gggmmg at verizon dot net
14. Reload3006 .432 w/penta, large round and plug pins Dcrop77380 AT aol DOT com
15. Live2Ride .432 w/penta pins Dan underscore harben at msn dot com.
16. tneck13 .432 w/penta and plug pins Telletoo AT comcast DOT net
17. Sheriff .432 w/penta pins crittrcallrATsbcglobalDOTnet
18. Steak Daddy .432 HP sdaley206 (at) gmail [dot] com
19. engine4on .432 w/penta and large round pins, handles. engine4on at gmail dot com
20. white eagle .432 HP whiteeagle 1 att charter dot net
21. shawnsmc .432 w/all pins shawn smc at hot mail dot com
22. SP5315 .434 w/penta, large round and plug pins wmclark AT email DOT com
23. AlabamaEd .432 w/plug pins Pefuehrer at knology dot net
24. Iron Mike Golf .434 w/penta and large round pins sugdenjw at msn daht com
25. IIJSavoy .432 w/plug pins iijsep at gmail dot com
26. twiggs1 .432 w/large round, penta and plug pins twiggs1 toyon.wiggs at gmail.com
27. Nix .432 w/penta and large round pins, handles greg at tacticaladvantage dot ca
28. readr1 4C .432 w/large round pins Readr1(at)yahoo dot com
29. spuddicus .432 HP w/large round and plug pins josh.panos AT geardogz DOT com
30. GlocksareGood .432 HP w/penta and plug pins B underscore maney at verizon dot net
31. Powersgt .432 w/plug pins and handles jlchapin att northstarbullets dot com
32. 3364Deer .432 w/penta and plug pins and handles sbowes At Shaw dOt cA
33. TMenezes .432 w/penta and large round pins Trmenezes "7" at g mail dot com
34. AaronJ .434 w/penta and plug pins aaronjondro at gmail dot com
35. bushog .432 w/penta and plug pins boo-haaa AT hotmail DOT com
36. gustusj .432 w/plug pins gustusj at yahoo dot com
37. Nix .432 w/penta and large round pins and handles greg at tacticaladvantage dot ca
38. RadioactiveMarine .432 w/penta and large round pins knaack(at)roadrunner(dot)com
39. chsparkman .432 solid mrsparkman AT mrsparkman DOT com
40. FLYCUTTER .432 HP r underscore kark AT att DOT net
41. swisscast .432 w/large round and plug pins swisscast AT bluewin DOT ch
42. hoplite .432 w/large round and plug pins hoplite dot junk at comcast dot net
43. PbHurler .432 w/large round and plug pins denneyr AT sbcglobal DOT NET
44. just10mm .432 w/large round and penta pins just10mm at gmail DOT com
45. root .432 w/large round and penta pins armalite_ar50 (at) yahoo (dot) com
46. cja245 .432 w/large round and penta pins cja245 at gmail dot com
47. harley45 .434 w/large round pins Eric at white tiger blog dot com
48. 338RemUltraMag .432 w/penta and plug pins trucker josh 9039 @ gmail . com
49. MDF99 .432 solid FRAROCKET (AT) AOL (DOT) COM
50. sparkz .432 HP Sparkz100 AT Gmail Dot COM
51. vaughan61 .432 HP w/large round and plug pins and handles vaughan61 at cox dot net
52. ben lurkin .432 HP w/large round pins sddnhad(aht)msn(dought)com
53. funshooter .432 w/all pins and handles weldinspector at earthlink dot net
54. kendwell .432 HP w/penta, flat and large round pins and handles kendwell AT searchglobal DOT net
55. bcr .434 HP w/penta, plug and large round pins brichards aat optics dawt arizona daught edu
56. lksmith .434 HP w/penta pins lksmith (underscore) 03 at yahoo dot com
57. BruMatt .432 HP w/penta, large round and plug pins and handles jmwbruce at aol dot com
58. 44 mag nut .434 w/large HP and plug pins magnut44 at gmail dot com
59. ------------------------------
60. Rodfac .434 w/large round and penta pins DLOBERG at BELLSOUTH DOT NET
61. Nabind .432 w/all pin options Drs dot 1964 at yahoo dot com
62.
63.
64.
65.

2 Cavity interest . .
1. rintinglen
2. Irascible
3. AlabamaEd
4. 258bob
5. 3364Deer
6. gustusj
7. 35 Whelen
8. jimb.
9. Rodfac
10. sparkz

[Dutch4122]

Please put me down for:

Four cavity brass mold, .434" diameter, small H/P pins, plus one set of flat nose "plug" pins.

dutch4122(at)yahoo(dot)com

Thanks!:CastBoolitsisbest:

[sffar]

updated.
Dutch4122 we'll need an email address for Miha to send the invoice
Grandpas50AE you've two options for the cast diameter.
Sam

[x101airborne]

Im in. 4 cav 432 diamater round and penta pins. x101airborne at yahoo dot com

[Grandpas50AE]

Sorry sffar, I meant to put that on there. Both in .432

[midnight]

Put me down for one 4 cavity, 0.432, small pins, & plug pins.

rwhyte@widotrrdotcom

Bob

[simonjester76]

Sam,

4 Cavity - .432" with HP pins and add large HP pins as well as "plug pins". Thanks!

n3efo AT comcast DOT net

Simonjester76

[Grandpas50AE]

I don't see my small HP pins on the list (should be small HP pins, Penta pins, and plug pins). It comes with one set, then the other two sets are $16 each set, right?

[simonjester76]

The HP pins are the small pins. The large HP pins are shown in 45 2.1's drawing (as the deeper cavity in the bullet).

Regardless you are correct. The mold comes with a set of "small pins", adding the large or Penta or plug pins would add $16 each.

Simonjester76

[sffar]

This, in fact, is a detail that never got worked out as to which of the two HP pin styles were standard, which were optional and whether one was a penta configuration. Also, the possibility of whether the customer may simply choose which single set of pins might be included. Yesterday I wrote to to Miha about this, and am awaiting a reply. I suggested the smaller HP pins be standard, and the larger be of the penta type and optional. I believe that's the typical arrangement. I've been treating it this way listing the orders. Hope it seems satisfactory, and I'm waiting for confirmation from Miha.
Sam

[Beau Cassidy]

.423 diameter. Large HP with plug pins. Smallmouth dot catcher at y.a.h.oo.com

[IIJSavoy]

Please add me to the list...

1 mold (4C, .432, Small HP, add Large Penta HP Pins) iijsep @ gmail dot com

[gunsbrad]

I'm in for 1 4 cav mould .434, small Hp, and extra set of plug pins. bradhurt2 at yahoo dot com

Can't wait.

Brad Hurt

[frankenfab]

I'll take a 4 cavity solid. .432

fdombek at phillipscorp dot com

Thanks,

Frank

[BRobertson]

I would like:

4 cav .432 small pins, plug pins

akstormy at mtaonline dot net

thanks

[rintinglen]

I'd prefer a 2 cavity mold==those 4 cavity brass molds get heavy fast.

[sffar]

I'd prefer a 2 cavity mold==those 4 cavity brass molds get heavy fast.
I believe many people agree with you, and I hope if they're interested they'll sign up. This could very possibly get run in both two and four cavity versions like the ongoing Mihec 358156 group buy.
Sam

[sffar]

Bump for a classic.

[Lucas]

Hi Sam,
Hope you are doing well. My barrel slugs at 0.430, should I opt for the 0.434? Any advice would be greatly appreciated.
Thanks for the reminder. Been out of the country for a bit, sorry I did not reply sooner. Work computer locks us out of non company sites...

I would really like a 2 cavity in the following orders, but if unavailable I would like to order 1 of each in:

4 cavity Large Hollow Point $120
Small HP pins $16
4 cavity solid $90

Shipping $20 (would it be $20 for a single order of the above?)

Total: $246 (if another $20 shipping is required, no problem)

[sffar]

Hi Lucas,
Measure the throats of your gun(s) and get the size that's close but a little bigger.
I'll put you down for 4 cavity molds, and as interested in 2 cavity's as well.
Just a reminder; you can cast solids with the hollow point mold.
Sam

[simonjester76]

Sam,

Looks like we are very close...

Simon Jester

[Reload3006]

when do you expect to get this rolling? if its a couple weeks to a month out I will take a 4 cavity .432 solid pin penta pin

[sffar]

when do you expect to get this rolling? if its a couple weeks to a month out I will take a 4 cavity .432 solid pin penta pin

Not likely a couple of weeks or a month. More like several months, at least–can't be sure. Let me know what you'd like to do.
Thanks,
Sam

[Reload3006]

Why I asked was because yesterday I just dropped 166 to Miha on a .452-200 cramer LOL so if its going to be months out is even better put me down.

[sffar]

Updated.
Reload3006, sorry I misunderstood your meaning. Billing won't be for a while on this one!
I put you down for penta and plug pins. Thus, you'll have small HP pins, larger HP penta pins and flat pins (which allow the mold to be placed on a hot plate when casting solids). As I believe you know, any of the hollow point pins can be reversed to cast solids but they'll project from the bottom of the mold when doing so.
Answered the PM. Please let me know which address to use. Thanks.
Sam

[Reload3006]

Updated.
Reload3006, sorry I misunderstood your meaning. Billing won't be for a while on this one!
I put you down for penta and plug pins. Thus, you'll have small HP pins, larger HP penta pins and flat pins (which allow the mold to be placed on a hot plate when casting solids). As I believe you know, any of the hollow point pins can be reversed to cast solids but they'll project from the bottom of the mold when doing so.
Answered the PM. Please let me know which address to use. Thanks.
Sam
Great use the Dcrop one.

[Lucas]

Hi sffar,
Thanks for all of your help and advice. Please replace my previous two selections with this one. Please put me down for:

Quantity 1:

0.434" , 4 cavity ($120), Large HP and Small HP ($16), Plug pins (solids) ($16), Shipping ($20)

[sffar]

Updated.
You're welcome, Lucas.
Sam

[skimmerhead]

put me down for a 2 cavity but will settle for a 4 cavity if there is not enough interest in the 2 cav. i want .432 gas check with penta and plug pins.
captainbogg at viscom dot net

skimmerhead :lovebooli

[sffar]

Updated.
Welcome, skimmerhead.
Sam

[sffar]

Movin' on up!

[simonjester76]

Bump to the Top!

[gunsbrad]

oh cmon. somebody else gotta be wantin this one.

Brad Hurt

[tnek13]

If it is not too late please add me to the list. I have not done this before so let me know the process – Thanks
Order = 1 mold - 4C, .432 ($120), Small HP, add Large Penta HP Pins ($16), add plug pins ($16) and handles (?) Shipping ($20)
Email - -----atcomcastdotnet

[sffar]

Hello tnek13,
You've got it all right. I add you name to the list (post#3) and when the time comes for Miha to make the mold he'll send you an invoice. Not long afterwards he'll ship your mold.

Sam

[midnight]

All tnek13 needs to do now is disguise the email address. I guess the crooks have a way of scanning and plucking out email addresses so the can bother you. Telletoo at comcast dot net.

[Grandpas50AE]

Sam,
Please change my Penta HP pins to large HP pins. Thanks.

[sffar]

Sam,
Please change my Penta HP pins to large HP pins. Thanks.

I wrote to Miha some time ago asking about whether Penta pins were part of the design (if they were, probably they'd be the larger pins) but never heard back from him. I'll try again. 45 2.1's drawing certainly showed large and small hollow points, but the question of whether there'd be pentas is still open. If the large are pentas, then getting round ones might be a special request (and vice-versa). I know I need to get a definitive answer on this. I'll take the pentas off your order for now if you like, and I'll push a little harder to get this straightened out.
Sam

[Sheriff]

Might as well get in on this one, too; 1 .432 with large pins, 4 cavity. crittrcallrATsbcglobalDOTnet.

Thanks

[sffar]

Updated.
Welcome, Sheriff.
Sheriff, I put you down for penta pins. At the moment I'm under the assumption the large pins are the penta's, and the small pins come standard with the mold.
Waiting to hear back from Miha to clarify exactly what he has in mind. I'd like to see large and small round, large penta and plug pins all available. We'll see.
Sam

[Steak Daddy]

I'd like a 4 cavity .432 with the large Penta pins.

steak-daddy (at) comcast (dot) net

Thanks a bundle,

Steve
Seattle, WA

[Sheriff]

Updated.
Welcome, Sheriff.
Sheriff, I put you down for penta pins. At the moment I'm under the assumption the large pins are the penta's, and the small pins come standard with the mold.
Waiting to hear back from Miha to clarify exactly what he has in mind. I'd like to see large and small round, large penta and plug pins all available. We'll see.
Sam

Thanks. I'm looking for the 'deeper', 'wider' cavity. I'll be running these in a .44spec, 30:1, at 800 to 900fps.

Russell

[Steak Daddy]

I'd like a 4 cavity .432 with the large Penta pins.

steak-daddy (at) comcast (dot) net

Thanks a bundle,

Steve
Seattle, WA

Just curious, if you still have any extra of the brass, 4-cavity, H&G #68, 200 gr SWC, plain base, 0.452, solid moulds available. I'd like one of those too. Otherwise, I will be first in line for the next run.

[Live2Ride]

I would like a .434 WW four cavity mold with both large and small hollow point pins. Dan underscore harben at msn dot com.

[sffar]

Updated.
Welcome, Steak Daddy. Have a look here . .
http://castboolits.gunloads.com/showthread.php?t=143551
Looks like you're in luck!

Regarding the large pins, still haven't heard back about large round pins, etc.. I do know the large penta pins ordinarily cast about the same weight as round. Looking at the drawing, the opening is approximately the same for large and small, and the large is deeper. I don't expect the large pins, whether penta or round, to produce a "flying ashtray" type boolit.
Soon as I hear back I'll post Miha's answer.
Sam

[Steak Daddy]

Sam, thanks for the tip off, I just sent a PM.

From my perspective, I'm fine with either Penta or Round in the large HP pins, whatever Mihec ends up offering.

Thanks for the welcome.

- SD

[phaessler]

Any idea or thought from Miha on the timeline for this one?
Thanks

Pete

[sffar]

Any idea or thought from Miha on the timeline for this one?
Thanks

Pete

I don't, except that I read Miha is going into business for himself, so maybe that means sooner than otherwise once he's not making moulds after hours.
Sam

[skimmerhead]

please remove me from the buy list. thank you

skimmerhead

[sffar]

Updated.

Welcome, Live2Ride.

skimmerhead, took you off the list.

Sam

[sffar]

Miha got back to me regarding the pin types for this buy . .

"Small, large and pentas will be available for this one."

He also hopes to have some pictures soon! I can't say for sure whether the penta pins will be large or small–usually they're large–but large and small round pins are available. For now we'll say small round are included, and large penta pins and round pins (along with plugs and blanks) are the options.
Sam

[sffar]

bump up

[Grandpas50AE]

Sam,
If small round pins are included, I would like to add a set of large round to both orders. I figure the large round will do nice for .44 Spl. and the small round will do well for the magnum.

[sffar]

Updated.
Roger, I had a feeling you'd go for the large round pins if they were offered. I agree they'll make it nice for a Special.
Sam

[midnight]

Please add a set of large HP pins to my order.

Bob

[Grandpas50AE]

Updated.
Roger, I had a feeling you'd go for the large round pins if they were offered. I agree they'll make it nice for a Special.
Sam

It probably didn't take much guessing on your part...;)

[Beau Cassidy]

Can you remove my request for penta pins? Thanks.

[sffar]

Can you remove my request for penta pins? Thanks.

Done. To the top . .

[2 dogs]

One .432" Dia, 4 cavity, HP mold for me.

fcgarza0640 AT hotmail DOT com

[sffar]

Updated.
Welcome 2 dogs.
Sam

[engine4on]

4 cavity .432 small pin mold. with large round and penta pins, handles

engine4on at gmail dot com

[sffar]

Updated.
Welcome engine4on.
Sam

[sffar]

I heard from Miha in response to my asking about a production date. In short, he's now making moulds full time (as of 5/1), is working double time and says that things should start to happen faster now. So, no firm date, but a big change which should mean there won't be so much waiting.
Sam

[Grandpas50AE]

Thanks Sam, good info for everyone to know.

[sffar]

Bumparoo time!

[Steak Daddy]

Hey Sam,

Upon further reflection, I think I'll be sufficiently happy with just the standard, large hollow point pins and have no need for the snazzy pentagonal pins. Please amend my order as we seem to be approaching the queue.

Thanks

SD
Seattle, WA

[sffar]

Hey Sam,

Upon further reflection, I think I'll be sufficiently happy with just the standard, large hollow point pins and have no need for the snazzy pentagonal pins. Please amend my order as we seem to be approaching the queue.

Thanks

SD
Seattle, WA

SD,
As it stands, I believe the smaller round pins are standard with the mold, while the large round, penta, etc. are options. Don't know for sure if Miha will offer a choice on a particular included set such as large round, but I don't think so. You could probably ask when he sends the invoice.
At any rate, I'll take the penta's off your order. If you'd like me to add large round please let me know.
Sam

[Dutch4122]

Sam-

FWIW would you please edit my order (#4 on the list) to specify small H/P pins in addition to the plug pins already listed.

Thanks,

[sffar]

Hello Matt,
All the HP moulds come with small HP pins. I've only been listing the optional pin sets, as the small HP set is included with all orders that aren't solids. I'd like to avoid changing the existing format so as to avoid confusion.
Miha will read your order as; .434 HP (includes small round HP pins) with optional plug pins added.
Okay with you?
Thanks,
Sam

[AlabamaEd]

I am interested in two cavity mould with small pins. Should this be a group buy please advise.

Thanks Paul

[sffar]

I am interested in two cavity mould with small pins. Should this be a group buy please advise.

Thanks Paul

Paul,
Put you on the interested list for a 2C. It could happen, though it would require some ten or twelve more signing on for it.
Sam

[Dutch4122]

Miha will read your order as; .434 HP (includes small round HP pins) with optional plug pins added.
Okay with you?
Thanks,
Sam

Fine by me. Thanks! :D

[white eagle]

I would like a 4 c deep pin .432
whiteeagle 1 att charter dot net

[shawnsmc]

I'll take a 4 cavity 432 HP all pins
shawn smc at hot mail dot com

thanks,
Shawn

[sffar]

Updated.

white eagle,
The standard pins are the shallower ones. For deep pins–additional–you'll have a choice of large round or penta. Please let me know which you'd prefer and I'll update the order.

Shawn,
I put your order in as requested. That'll include small, the two types of large, plug and grind your own blanks. Just so you know.

Sam

[HighHook]

One .432" Dia, 4 cavity, large HP pin mold for me.

Pvolkman3 at gmail dot com

[sffar]

Updated.

HighHook,
The standard pins are the shallower ones. For deep pins–additional–you'll have a choice of large round or penta. Please let me know which you'd prefer and I'll update the order.

Sam

[258bob]

I'd prefer a 2 cavity mold

[sffar]

I'd prefer a 2 cavity mold

Put your name on the 2C interest list.

Sam

[AlabamaEd]

Please put me down for:

Four cavity brass mold, .432" diameter, small H/P pins, plus one set of flat nose "plug" pins.

Pefuehrer at knology dot net

Thanks,

Paul

[sffar]

Updated.
We're on a tear, here! Welcome to all new buyers.
Sam

[white eagle]

Standard is fine

[sffar]

Standard is fine

Sounds good. Just the standard pins included in the buy.

Sam

[sffar]

Link sent to Miha for schedule listing.
To the top . . .
Sam

[sffar]

To Page 1!
Sam

[simonjester76]

Sam,

Been busy but still most interested. Perhaps Miha may be able to post a schedule before long...

Simonjester76

[sffar]

Sam,

Been busy but still most interested. Perhaps Miha may be able to post a schedule before long...

Simonjester76

I hope he will. According to my own research, there should be one mould separating the 429244 and the 358156. I believe this one's roughly fifth in line right now in the order of buys.
Sam

[BRobertson]

Sam,

At the risk of being a PITA can you please change mine to a solid, and

add a set of handles!!??

I am #12 0n the 4c

Thanks much!!!

Bob

[sffar]

Updated.
No problem at all, Bob.
Sam

[sffar]

Up to the front row . . .
. . . and with enough interest a 2C is also possible.
Sam

[Iron Mike Golf]

1 mold:

.434
4C
Large HP
Small HP
Penta HP

sugdenjw at msn daht com

[sffar]

Updated.
Welcome, Jeff! Small round pins are included, so I added the large round and pentas on your order.
Sam

[Iron Mike Golf]

Thanks, Sam!

[IIJSavoy]

sffar,

Can I jump back into this GB? If I can, I'd like:

1 - 4C .432 HP (small) w/ plug pins iijsep at gmail dot com

Let me know (I'll watch the post).

Thanks,

[sffar]

Updated.
IIJSavoy, welcome back. No problems at all making changes until Miha closes the buy.
Sam

[kbstenberg]

From everything said so far this is strictly a GC bullet?

[sffar]

From everything said so far this is strictly a GC bullet?
Yes, it is. Along the lines of the original.
Sam

[emj]

Put me down for:

Two cavity brass mold, .432" diameter, small H/P pins, plus one set of flat nose "plug" pins.

Thanks,
Ed

[sffar]

emj,
I put you down as interested in a 2C, though it'll take about fifteen people for that to be cut in addition to the 4C. That is, it's not a sure thing right now. About ten more buyers are needed.
Only the 4C is a sure thing right now.
I hope it happens, as Miha's 2C molds are popular for many people who find the 4C mold a bit heavy to handle. Plus, 2C molds are also a bit less money.
Sam

[Dutch4122]

Edited: I just realized this request was already made previously. My apologies.

Thanks.

[sffar]

I just noticed that my order (#4 on the list) does not show that I also want a set of small H/P pins in addition to the "plug" pins.

Please add the set of small H/P pins to my order.

Thanks.

Dutch4122,
The small HP pins are what's standard, so the order only reflects additional parts.
Sam

[twiggs1]

Count me in for a HP four cavity .432 HP with all pins.
twiggs1 toyon.wiggs at gmail.com

Thanks!!

[sffar]

Updated.
twiggs1, welcome. You're #26. If you could, please review your order there for accuracy.
Thanks.
Sam

[sffar]

To the top of the heap!

[Nix]

Put me down for a 4-cavity HP .432 with one set large round pins and one set penta pins plus handles. greg at tacticaladvantage dot ca

[sffar]

Updated.
Nix–welcome!
Sam

[emj]

Sam,

Can you change my order to a .432, four cavity, solid.

Right now I'm #5 in the 2 cavity list.

Thanks
Ed

[sffar]

Updated.
Ed (emj), I'll need your disguised email address for Miha's invoicing.
Sam

[spuddicus]

I'd like to get in on this please....

1. Mold w/ Large pins
2. .432 diameter
4. Extra set of: plug pins, small pins

josh.panos AT geardogz DOT com

[GlocksareGood]

I would like a 4 cavity HP mold with penta pins and plug pins. .432 Diameter
B underscore maney at verizon dot net

[emj]

Sam,

My email is

edward.jansen at att dot net

I'm # 28 on the list.

Thanks
emj

[sffar]

Updated.
Welcome, spuddicus and GlocksareGood.
spuddicus, the mould comes with small pins, so I noted your order accordingly. Feel free to make changes.
Sam

[Powersgt]

Sam,

Please put me down for 1:

.432 4CAV HP W/ extra set of plug pins and handles.

jlchapin att northstarbullets dot com

Thank you,

Jeff

[3364Deer]

Sam my Good Man,

I would like to order one 4 cavity small HP .432 mold. In addition, I would also like to order both the penta pins, plug pins and a set of handles. You could also put my name on the list as interested in the two cavity mold. Many Thanks.

sbowes At Shaw dOt cA

[sffar]

Updated.
Welcome, Powersgt and 3364Deer!
Sam

[TMenezes]

Sign me up for a .432 hollow point with the big pins, and Penta pins if they are available. If they aren't no worries. Trmenezes "7" at g mail dot com

Thanks 8-)

[sffar]

Updated.
Welcome, TMenezes!
Sam

[AaronJ]

I will take a 434 4 cav with penta, small and plug pins please. aaronjondro at gmail dot com

[bushog]

Bushog would like to be included for a 4 cavity .432 w/penta, HP and plug pins. boo-haaa AT hotmail DOT com

[sffar]

Updated.
Welcome, AaronJ and bushog. Molds have the smaller HP pins included, so both your orders have additional plug and penta pins listed.
Sam

[Lucas]

Guys, please pull me from the list. I just received my NOE moulds for 44 mag PB and am shooting one ragged hole at 25 yards. Can't do much better than that. Thanks for all of your help.

[sffar]

Updated.
Sam

[HighHook]

Hey Sam, could you pull me off from the list #22

Thanks

[sffar]

Updated.
Still no word back from Miha on a production date.
Sam

[Irascible]

This looks like a chance to get a 429244 that will cast the right size with out going to Lyman #2 :>) I need to end up with .431 out of 50/50 alloy. so it seems .434 would be best.
I'd like to order a 2 cavity .434 solid. NO pins at all. If the large pins were not so big at the top, I would order a mould with HP pins, but looking at the sketch it looks like a bigger diameter than I want. So, I think I'm better off ordering solid and and having Erik do his magic.

[sffar]

Irascible,
The 2 Cavity mold will only get cut if there's enough interest. For the time being the 4 cavity is what's going to get made. I put you on the 2C interest list, so if you want to order a 4 cavity let me know.
The HP version will come standard with the small HP pins–the shallower of the two lines on the diagram.
Thanks.
Sam

[Irascible]

Does any body know what the diameter of the 2 different pins are?

[sffar]

Does any body know what the diameter of the 2 different pins are?

45 2.1 would have to provide that detail. The smaller cavity amounts to about 10 grains worth of lead.
Sam

[doctorggg]

Please add my order. 4 cavity large hp pins, small hp pins and flat pins.

[doctorggg]

I always forget .432 and gggmmg at verizon dot net

[sffar]

Updated.
doctorggg, welcome! Slipped you into the #13 slot. FYI, the penta pins will amount to large hp pins, as well as the large round.
Sam

[doctorggg]

Many thanks sffar. Greg

[simonjester76]

Sam,

Still in and patiently waiting...

Simon Jester

[sffar]

Sam,

Still in and patiently waiting...

Simon Jester

Glad to hear it!
Me, too.
Sam

[sffar]

BUMP for the New Year!!
Sam

[SP5315]

What the heck, I'm in. 4 cav w/penta and large round, & plug pins. in .434

wmclark AT email DOT com

[gustusj]

If it's not too late, please add me to the list.
2-cavity if it happens, if not I'm good with a 4-cavity, .432, small pin and a plug pin.
gustusj at yahoo dot com
Thanks!
Gus

[Nix]

(1) 4-Cavity Brass, Large-HP Round-Pins and Large-HP Penta-Pins .432 with handles, please.

greg at tacticaladvantage dot ca

[RadioactiveMarine]

Please add - RadioactiveMarine 4 cavity .432 w/penta and large round pins knaack(at)roadrunner(dot)com.

[sffar]

Updated.
Welcome, SP5315, gustusj, Nix and RadioactiveMarine!
Sam

[simonjester76]

Shameless Bump to top...

Simon Jester

[chsparkman]

please put me down for a 4-cav .432 solid. mrsparkman AT mrsparkman DOT com

[FLYCUTTER]

FLYCUTTER , 1 mold, .432 , 4 cavity ,small HP pins, r underscore kark AT att DOT net

[swisscast]

Received my first 4-cavity molds three weeks ago – a 359-640 HP and a 454-640 HP. To say that I’m highly impressed by the design, build quality and ease of work with these two beauties would be a huge understatement… If it’s not too late, please add me to the list: one 4-cavity mold, .432, large HP and plug pins (no pentas).

swisscast AT bluewin DOT ch

Thanks!

[sffar]

Updated.
chsparkman, FLYCUTTER and swisscast–welcome!
Sam
Nice bump, simonjester76.

[hoplite]

One 4-cavity in .432, w/ small, large and plug pins, please.

Thanks for running this buy.

hoplite

hoplite dot junk at comcast dot net

[PbHurler]

Ok, not waiting anymore,

(One) 4-cavity in .432, w/ small, large and plug pins

denneyr AT sbcglobal DOT NET

[just10mm]

I would like a 4-cavity in .432 w/ small round pins, large round and penta pins

just10mm at gmail DOT com

Thank you

[harley45]

I want a 4 cavity solid
.434 dia
Eric at whitetigerblog dot com

[sffar]

Updated.
Welcome hoplite, PbHurler, just10mm and harley45.
Sam

[hoplite]

Thanks Sam. I'm not familiar with your list nomenclature, but please make sure my request, #42, includes both small and large (round) HP pins and plug pins.

Steve



Updated.
Welcome hoplite, PbHurler, just10mm and harley45.
Sam

[sffar]

Thanks Sam. I'm not familiar with your list nomenclature, but please make sure my request, #42, includes both small and large (round) HP pins and plug pins.

Steve

All HP mold orders will include the smaller HP pins, while the optional large HP and penta pins will result in about the same size cavity (and weight). All HP pins may be reversed to cast solids, while the plug pins are an option to allow people who like to preheat on a hotplate to rest the mold flat when doing so.
Sam

[Fernando]

First try at this - If it happens 2 cavity solid .432
What next??

[sffar]

First try at this - If it happens 2 cavity solid .432
What next??
You'll get put on the interested list for a 2C mold. Subscribe to the thread, or check back regularly, and see if enough people sign up to move it forward. If it happens the details will get listed and you can confirm your requested specs along with your email address for invoicing.
Sam

[root]

$120/4C + $16 additional pins + $20 shipping

With Large pin,s and pentagon pins, for a total of 132.00 and shipping of 20.00 for a final total of 152.00

Says it comes with the small pins right?

armalite_ar50 (at) yahoo (dot) com

E-mail with payment details and such.

Thank you

[harley45]

Remove me from this one please. I'm consolidating calibers And the 44 lost out

[root]

I'll take harley45's
Order with the rest of what I listed. ( the extra pins)

Thanks.

[sffar]

Updated.
Welcome, root. I put you in at #45 spot in harley45's prior place. It does include small pins. The size harley45 had listed was .434. Miha will invoice you at the email address when the buy closes.
Sam

[root]

This will be shot in a 629 mountain gun
Marlin 44 lever gun
and taurus 44 spc.

So I will need the .432 NOT the .434

If you could just change that @ the sign up to reflect the 432


Thank you for getting me in on this.

[Live2Ride]

Please change my order number 15 to 432 diameter from 434 diameter.

[sffar]

Updated with changes.
Sam

[root]

Roughly how long does a group buy go on for?

Is it numbers sold or member in?

Just wondering.
Thanks

[cja245]

I'll take a .432 dia. 4C HP mold with small, large, and penta pins.

cja245 at gmail dot com

Thanks

[sffar]

Updated. Welcome cja245.

"Roughly how long does a group buy go on for?
Is it numbers sold or member in?
Just wondering.Thanks."

I suppose you could say roughly a year, but it depends on the maker and how they determine what's next. So far as I know Miha has not stated a policy regarding his scheduling. All I can say is, it's got to be sooner rather than later, or at least I hope so.
Sam

[readr1]

Put me down for a 4 cavity .432 with large and small pins please.
Readr1(at)yahoo dot com

[harley45]

I know I asked to be off this one but a 1894 just fell into my lap so I need a 4 cavity small and large pins gc and in the largest dia possible.
Thanks

[emj]

Could you please take me off this list. I'm #28.

Thanks,
EMJ

[Reload3006]

Sam I am number 14 could you update for Large hp pins Penta pins small hp pins and plug pins please. Dcrop77380 at aol dot com. Hope Miha is getting close to this one. .... One other question just to make sure this is a gas check mold correct? or is that optional? if optional I want gascheck.

[sffar]

Updated.
All HP molds will come standard with the smaller round HP pins, so if it's not listed don't worry. Also, this buy is for a GC mold only.
Welcome readr1 and harley45 (email address needed for invoicing).
Sam

[338RemUltraMag]

Ok I will take a 4 cav with the penta pins and flat pins in .432 diameter, so the total should be $156?

Thanks!

trucker josh 9039 @ gmail . com

[sffar]

Updated.
Welcome 338RemUltraMag.
I figure $172. $120 (mould w/standard pins) +2x16 (additional pin sets) +20 (shipping)
Sam

[jimb.]

This is my first time, so I'm not sure how it's done. I'd like the large HP mould, 2-cavity, .432 (I think .432, anyway - I use 1 part tin, 16 parts lead alloy, cylinder throats .4325", bore is .4295"). So, cost would be $90? If you need any more info., let me know.

I don't know how this system works, so I don't know how, when, or who to pay, etc.

jimb.

[Dwayneinfo]

I am in for a 4 cavity .432 with all pin options please.

Dwayneinfo at yahoo dot com

[simonjester76]

Sam,

Please add large HP pins to my order... Thanks!

(So, I'll end up with small HP [standard], Penta, Large HP and Plug pins)

Simonjester76

[vaughan61]

I would like:

4 cav .432 small pins, large pins, plug pins, and handles

vaughan61 at cox net dot com

[ben lurkin]

I'll take a 4 cavity 0.432" with lg hp pins.

sddnhad(aht)msn(dought)com

[jimb.]

C'mon, everyone! Please go in for a 2-cavity mould!!. I'm really hoping to get one of these in a 2-cavity.

Jimb.

[vaughan61]

Correction to email address for vaughan61:

Correction to correct the email address.
My 03-11-13 request should read:

4 cav .432 small pins, large pins, plug pins, and handles

vaughan61 at cox dot net

[hotbrew]

I am in for a 4 cavity .432 with all pin options and handles please.

guy.jones at gmail dot com

[kendwell]

I'd also prefer 2 cav, but will take 4 cav, penta and plug pins, .432, and handles

kendwell@searchglobal.net

[bcr]

I'll have one. .434" please with all pins, including flat.

brichards aat optics dawt arizona daught edu

[kendwell]

I'd also prefer 2 cav, but will take 4 cav, penta and plug pins, .432, and handle

Update to all available pins, small, large, penta and flat

[35 Whelen]

I take it this buy is still open? Has there been enough interest in the two cavity to warrant production? Hope so as I'm interested.

35W

[harley45]

My email is Eric at white tiger blog dot com

[simonjester76]

Sam,

Gotta be gettin' closer... A number of buys that were posted after this one are closed and awaiting production...

Simon

[35 Whelen]

I don't know. I posted above with no response and I PM'ed sffar with no response from him. Still waiting....

[simonjester76]

35 Whelen,

Sam will eventually reply... He does get busy at times. The buy AFAIK is still open for 4 cavity molds (and will be until Mihec tells Sam to close it). The molds are so good that it is worth the current more than a year from the initial request to now. If nothing these buys have taught me to be very, very patient.

Regards,

Simon

[lksmith]

I just joined this site because of this buy to make sure I didn't miss out when Miha gets these cut


This will be my second MP Mold (I bought 45-200 4 cav) and the quality is certainly worth waiting for
Please put me down for a 4 cavity with set Penta Pins which I show to be $156. I would prefer the large HP as the set that comes with the mold if possible instead of the small ones, but if not I can always use the pins from my other MP mold my Email address is lksmith (underscore) 03 at yahoo dot com.
I just received the following email from Miha this morning:

Hi,

Sorry for late reply.

As we speak I don't have any 429244-Cramer-HP on hands.
I will machine some more, but hard to tell any exact date. I'm prety booooooooked right now.

Best regards,
Miha

[Fernando]

Sorry but you can take me off the 2 cavity wish list.
Just scored a vintage single in the swappin section.
As I was gonna do solids anyways I jumped.
Maybe next time

[Grandpas50AE]

Sam will reply soon.

[sffar]

Updated.
Sorry for the delay, and slow response to PM's. Thanks to Simonjester76 and Grandpas50AE for keeping things rolling.
Welcome, MDF99, jimb., Dwayneinfo, vaughan61, ben lurkin, hotbrew, kendwell, bcr, 35 Whelen and lksmith!
Those who wanted all pins, I put you down for all except the grind your own style. If you'd like that option as well please let me know.
lksmith, thanks for the reply from Miha. I'll try him again. I'll need a size from you, by the way. This buy can't go on forever, though it will be worth the wait provided we don't all become ancient in the meantime.
Sam

[lksmith]

Updated.
Sorry for the delay, and slow response to PM's. Thanks to Simonjester76 and Grandpas50AE for keeping things rolling.
Welcome, MDF99, jimb., Dwayneinfo, vaughan61, ben lurkin, hotbrew, kendwell, bcr, 35 Whelen and lksmith!
Those who wanted all pins, I put you down for all except the grind your own style. If you'd like that option as well please let me know.
lksmith, thanks for the reply from Miha. I'll try him again. I'll need a size from you, by the way. This buy can't go on forever, though it will be worth the wait provided we don't all become ancient in the meantime.
Sam

.434 Since it's easier to size down than up

[hotbrew]

Would you change my 4 cavity .432 to a .434 with all pin options and handles please.

Thanks,
hotbrew

guy.jones at gmail dot com

[BruMatt]

Please put me on the list for a 4 cavity .432 mold with all pin options (small round, large round, penta and flat) and handles.
jmwbruce at aol dot com.

[44 mag nut]

I'll take 4C .434 large HP and plug pins.
magnut44 at gmail dot com

[Darkh2odiver]

I'll take a four cavity, solid, 432 with handles.

darkh2odiver (at) hotmail [dot] {com}

Thank you
Scott

[Rodfac]

Please add me to list: .434 Dia, small, lg and penta pins, two cavity. If only the 4-cavity is run, I'll take that in lieu of the Two cavity.
DLOBERG at BELLSOUTH DOT NET

Best Regards, Rod

[Nabind]

I will take a four cavity .432 with all pin options. Thanks

Drs dot 1964 at yahoo dot com

[Darkh2odiver]

Found 44 mould. Please take me off this GB. Post #198

Thank you

[sparkz]

MiHec edition of the classic Lyman/Thompson 429244 HP

two cavity brass HP mold,, First Choice,,,
four cavity brass HP mold,, Second Choice

.432 as droped, I want to use / size this for our .44mag
(it comes with the 241gn. Large HP Pins Correct?)
Can I reverse the Large HP Pins for a 259gn. solid?
if not I will need a set of Plug Pins,, so I can make a HP or Soild from same mold, just to be clear,,

Sparkz100 AT Gmail Dot COM
What / whos Handles fit this mold?

please advise when Ready
I Can't wait,,,, But Guess I will have to if I want it,,, hahaha
Patrick & Sean Campbell

[lksmith]

MiHec edition of the classic Lyman/Thompson 429244 HP

two cavity brass HP mold,, First Choice,,,
four cavity brass HP mold,, Second Choice

.432 as droped, I want to use / size this for our .44mag
(it comes with the 241gn. Large HP Pins Correct?)
Can I reverse the Large HP Pins for a 259gn. solid?
if not I will need a set of Plug Pins,, so I can make a HP or Soild from same mold, just to be clear,,

Sparkz100 AT Gmail Dot COM
What / whos Handles fit this mold?

please advise when Ready
I Can't wait,,,, But Guess I will have to if I want it,,, hahaha
Patrick & Sean Campbell

Lee 6 cav handles fit

[Dwayneinfo]

Please remove 50. Dwayneinfo .432 HP w/all pin options Dwayneinfo at yahoo dot com

[funshooter]

Put me down for a 4C .432 brass with a gas check and all of the pins and handle.

weldinspector at earthlink dot net

[simonjester76]

Got to be getting closer...

Brass, check... Primers, check... Sizing & lube Die, check, Lube, check... Powder, check... even have the gas checks... Just need the mold now.

[hotbrew]

Please remove me from group buy

53. hotbrew .432 HP w/all pin options and handles guy.jones at gmail dot com

I picked up the 434-640 from Mihec

hotbrew

[simonjester76]

Sam,

Saw your other posting. Glad you are back!

Simon

[sffar]

Hello all,
Thanks, Simon. I'm back in the saddle. Getting caught up with the 358156, and should be getting to this one by tonight or tomorrow.
Sam

[sffar]

Updated.
Welcome Brumatt, 44 mag nut, Rodfac, Nabind, funshooter and sparkz.
sparkz, the smaller round HP pins are standard, Penta, large round, plugs (for laying flat) and blank (grind your own) are optional. The HP pins can all get reversed for casting solids. I left your order with the smaller standard pins. Please let me know if you want changes.
I'll be writing to Miha, and will post any information on when this is likely to get made.
Sam

[lksmith]

Sam,
Thanks for the update, I'm really anxious on this one, bought a Lubsizer (3 actually since it was a good deal), got Gas Checks and sizing die.
Since my 45cal Mihec mold I'm hooked on these custom molds!

[BRobertson]

Hi Sam,

Please change my email to:

akstormy at kpunet dot net

I am # 12 on the 4 cavity list

thanks

Bob

[sffar]

Changes made.

"Since my 45cal Mihec mold I'm hooked on these custom molds!"

I'm hooked, too. Miha's work is first rate and reasonably priced. Can take a while to get, though!
Sam

[Cast of Thousands]

Please put me down for 1 .432 4 cavity large hollow point gas checked brass mold.
Thanks
Ronald rodina at sbc global dot net

[Hamish]

I would be interested in a 2C mould.