311290 Dual Brass/Alum GB mould

[Blammer]

From this thread is where it started.
http://castboolits.gunloads.com/showthread.php?t=110516

I will be running the GB and we well be using Night Owl Enterprise (NOE) to make the moulds.

A minimum of 15 orders for moulds is required to waive the tooling cost and be placed on the production schedule for either Brass or Alum.

There will be two separate buys for this, one for Brass and one for Alum. These will be ran at the same time. So state what you want.

Post your order on this thread. I will keep the post below this updated with the orders. When the 15th order has been placed (doesn't have to be paid for) we will then be put on NOE's production schedule.

You may order any number of cavities available. You will just need to pay the appropriate price.
ALUMINUM Mould prices
(there will need to be 15 orders for aluminum in order to get this on the production schedule)
1 cavity moulds are $68 ea.
2 cavity moulds are $72 ea.
3 cavity moulds are $79 ea.
4 cavity moulds are $85 ea.
5 cavity moulds are $92 ea.

BRASS Mould Prices
(there will need to be 15 orders for brass in order to get this on the production schedule)
Single cavity brass mould $90.00 Ea.
Double cavity brass mould $94.00 Ea.
Four cavity brass mould $111.00 Ea.

The hollow point option for one cavity will be the standard $35.
Blank Hollow point pins will be an extra $1.50 each.
There will not be an RG option.

Plain base and GC options are available.
You may mix and match PB and GC in the same mould.
Shipping to you with insurance will be $10

A Lyman, RCBS type top punch is included along with sprue lube.

I'm the honcho

Darrell Steenwyk
112 Old Lime Kiln Rd
Arden, NC 28704

What you must do:
Send me a letter with your handle, your shipping address, what you ordered, and the money. (check or MO is fine)

The buy will remain open until one month prior to production. ONE MONTH PRIOR TO PRODUCTION I WILL CALL FOR PAYMENT. You do not need to pay prior to this, but you can if you want.
When I call for payment I will need all payments in within the week or you will miss out.

For those out of country please PM me for details on payment options and shipping costs.

NOE will ship them all to me and I’ll test cast with a few of them and then if all is well, send out the moulds.

The buy will remain open until one month prior to production, then it will close and a call for payment will be made.

Here is a link to the production schedule.

http://castboolits.gunloads.com/showthread.php?t=142415
Only one size will be ran .312x.302 nose.

Here are the pics with dimensions

http://i54.photobucket.com/albums/g81/blammer8mm/Cast%20boolits/311291/1111-029-311290.jpg

[Blammer]

Alum moulds will be offered in this also.

NOE has decided they will run it in alum, no sense haveing just the brass option. It would be NICE to have 15 or more in the alum but that is not necessary.

If you want to change from Brass to Alum, just post here and I will set it straight, and square the money difference too.

Who wants what for BRASS.
All moulds are GC unless otherwise stated.

1. brassmagnet 4C
2. rockrat 4C
3. mannyCA 4C 2GC 2PB
4. midnight 4C GC drill for probe
5. strikeromalley 4C
6. starbits 4C
7. bwgdog 4CPAID
8. 5. dominicfortune00 4C
9. Blammer 4C + HP; drill for probe
10. Ugluk 2C
11. NYbushbro 2C
12. chboats 2C
13. adk mike 2C
14. semtav 2C PAID
15. 12. mibo 2C
16. hotwheelz 2C
17. shakey jakey 2C
18. chrisw 4C +HP; Drill for probe
19. devers454 2C + HP
20. coltman 4C 3GC 1PB; drill for probe
21. paulinski 2C
22. shakey jakey 4C 3GC 1PB


Who wants what for ALUM.
All moulds are GC unless otherwise stated.

1.
2.
3. C1PNR 4C
4. dromia 4C drill for probe
5. sundog 4C GC PAID I owe some $'s
6. fatnhappy 5C
7. mrpeabody 2C GC
8. wrench 4C 2GC 2PB
9. waynes 5C
10. davidaker 2C
11. Buzzard II 5C + HP;Drill for probe
12.trapaddict 4C Drill for probe
13. cattleman 3C alum 1PB 2GC + HP; + 2 extra pins ;drill for probe

[Blammer]

updated post #10

[starbits]

Been looking like this was going to die, glad to see it is still breathing. I am in for a brass 4 cav GC

Starbits

[no34570]

Blammer
I'll take a 3 Cavity Gc .312 Aluminium please ;)

[bwgdog]

Blammer-one Brass-two cavity-GC. Thank You barry

[RugerFan]

I'll take a 4 cav brass.

[dromia]

I'm in for a four cavity Aluminium please. :D

[Blammer]

updated post #15

[dromia]

Forgot to say, would you drill for probe please.

[no34570]

Forgot to say, would you drill for probe please.

Me too please?

[Mibo]

Put me down for a 2 cavity GC - Aluminum
Thanks

[chboats]

but me down for a 2 cavity brass GC

Thanks
Carl

[Blammer]

updated post #21

[sundog]

Blammer, thanks for running this. Since I was the one who initially started talking about this months ago.

I'm in for a 4 cav aluminium.

[Blammer]

you're welcome!

Just one mould for you? No HP option?:kidding:

[C1PNR]

Yep, a 4 C Aluminum sounds just fine for me as well.

Thanks Sundog for starting the conversation, and thanks to Blammer for starting the the GB.

[Springfield]

I could use a 4 cav aluminum also.

[NYBushBro]

Please put me down for a 2 cavity GC BRASS mold. Thanks.

[Blammer]

updated post #25

[dominicfortune00]

I'll take a 4C GC in brass.

[Blammer]

list updated

[fatnhappy]

Blammer,

Put me down for a 5C Aluminum

[Blammer]

Who wants what for ALUMINUM.

1. no34570 3C drill for probe
2. dutch4122 5C OR
3. dromia 4C drill for probe
4. mibo 2C
5. sundog 4C PAID
6. C1PNR 4C
7. springfield 4C
8. fatnhappy 5C
9. waynes 5C
10. chboats 4C OR
11.
12.
13.
14.
15.

Who wants what for BRASS.

1. starbits 4C
2. bwgdog 2C
3. rugerfan 4C
4. chboats 2C
5. NYbushbro 2C
6. dominicfortune00 4C
7. quasi 4C
8. dutch4122 4C
9.
10.
11.
12.
13.
14.
15.

[quasi]

I am in for a 4 cavity BRASS g.c.

[starbits]

We are half way there. Keep it going.

Starbits

[63 Shiloh]

I am keen for a 4 cav brass mold, just need an idea of production date please?

Looking at a 4 cav brass, 3 GC, 1 PB, dependant upon production date.

Mike

[Blammer]

production date is "who knows" it is dependant on when we get the 15th order. At that point we will be put on the production schedule.

[NYBushBro]

I guess most guys have one of these... but not in BRASS - with a HP!
Hope this stirs some interest...!

[fatnhappy]

Blammer,
I now find myself in possession of a saeco sizer.

Would NOE be willing to grind a saeco style top punch for me, and if so what would be the cost associated with such a service?

[RugerFan]

C'mon folks, get them while they're hot!

[Wayne S]

I'll take a 5 cavity W/ GC ALUM.

[Blammer]

sorry dean, I don't know, you'd likely have to contact NOE directly.

wayne s, you're on the list

[Wayne S]

production date is "who knows" it is dependant on when we get the 15th order. At that point we will be put on the production schedule.

:violin: "can't un-ring a bell" or can we ?? Who would be willing to switch their choice of metals to get this one on the production schedule ??
1. Wayne S ,I would be willing to switch from Alum. to brass

[Blammer]

If you want to switch that's not a problem, I can change it!

[Wayne S]

I asked to see who else would be willing to change to make 15 buyers so this design can get on the schedule and delivered before Christmas.
I'll watch this for a week or so to see who else will be willing to switch either way, and see what the mood is, and go from there

[chboats]

I would be willing to switch to a 4 cav Alum if it would speed this up. I am currently down for a 2 cav brass. Either one is good with me.

Carl

[Springfield]

I'd switch from 4 cav al to 4 cav brass if I had to, but the aluminums are ahead right now.

[Blammer]

updated post #49

[Wayne S]

WE need 5 more for the Alum. GB or 6 for the brass GB, as I'ld be willing to switch to brass. Start telling your fellow casters

[BCall]

I would like one in brass. Haven't decided on 2 or 4 cavity yet, but it will be brass. Thanks, Billy

[Adk Mike]

I'm in put me down for a two cavity Aluminum. Mike

[Blammer]

list updated

[Wayne S]

We NEED 4 more to make 15 for the brass mold WHO WILL SWITCH ????



1. no34570 3C drill for probe
3. dromia 4C drill for probe
4. mibo 2C
5. sundog 4C PAID
6. C1PNR 4C
7. springfield 4C
8. fatnhappy 5C

[Springfield]

When we get down to needing 2 more for brass and 4 for aluminum I will switch, but I still am holding out for more guys to go aluminum.

[Blammer]

updated post #63

[Blammer]

arrgh, I need this like I need another hole in my head.

[C1PNR]

Well, it looks like we still need a few for the aluminum version so let's get on it.[smilie=2:

[NYBushBro]

Nice to see the lists filling up... all we need are 7 brave souls to seal the deal!

[NYBushBro]

bump to top...

[walltube]

Blammer,
I now find myself in possession of a saeco sizer.

Would NOE be willing to grind a saeco style top punch for me, and if so what would be the cost associated with such a service?

"The perfesser"

He may be our new scource for SAECO type top punches.

Y.T.
Wt.

[bwgdog]

Bump to top for brass....

[quasi]

Sorry, I am out. I am going the Accurate molds route, much less of a wait.

[Blammer]

not a problem.

I can understand your not wanting to wait.

[94Doug]

regarding the Saeco sizer, there is also an adapter to make the NOE fit out there. Was that Eric HP service, maybe?

Doug

[NYBushBro]

bump to top...

[RugerFan]

Aw c'mon fellers! We only need 4 more to make the brass run a go. If we get up to 14 fairly soon, I may just order a 2nd to put us over the top. Step right up and order one today!!!

[semtav]

I'm in for a 2 cav Brass GC

[Blammer]

list updated

[bwgdog]

Bump for Brass

[Blammer]

updated post #83

[NYBushBro]

bump to top... for more eager folks.

[RugerFan]

C'mon folks....just a couple more and this one is on the schedule!

[Blammer]

some of you can buy two of them and then sell one later. :)

[bwgdog]

Blammer-Please put me down for another 2C brass-My son in law is getting started with shooting-can,t think of a nicer present than a real brass in spec mold! Barry

[RugerFan]

Ok guys, we need to move this along. In addition to the one I already have on order, I will also take single cav with hollow point. Who's next?

[Alchemist]

I'm in for a 2 cavity BRASS GC. Just 1 more brass mould needed to make the schedule.

[Springfield]

I guess I gotta switch to brass, 4 cavity. That makes 15.

[bwgdog]

Thank You Springfield!!!!!!

[Alchemist]

Thank You Springfield!!!!!!

+1...That 4 cavity in brass is gonna be a bit heavy, but you'll make boolits so fast that you'll have all you can shoot before you know you're tired! :razz:

[Blammer]

updated post #83

[bwgdog]

Blammer-Will this get us on the schedule now? tia Barry

[Blammer]

yes, I'v PM'ed NOE to put us on.

[semtav]

I sent a check your way a couple days ago

[sundog]

Blammer, switch me from 4C aluminium GC to 4C brass GC. Additional funds going in mail today. Thanks.

[SwedeNelson]

Got this one on the schedule.
Will get the brass form tool on order.

Thanks to all that ordered.
Swede Nelson

[Blammer]

sundog, done

[NYBushBro]

HONCHO - please make sure that my order specifically states "2 cavity 2GC" - as it doesn't say that on the list.

[Alchemist]

HONCHO - please make sure that my order specifically states "2 cavity 2GC" - as it doesn't say that on the list.

Ditto

[bwgdog]

Also 2 cavity 2 GC - bwgdog

[Blammer]

updated post #97

[semtav]

HONCHO - please make sure that my order specifically states "2 cavity 2GC" - as it doesn't say that on the list.



All moulds are GC unless otherwise stated.

per instructions

[Blammer]

yep, just added that to clarify, or make it more better easy understood. :)

[Blammer]

list updated

[NYBushBro]

So... is the brass mold a GO?

[Blammer]

yes, brass is a go and we're on the schedule for brass.

I'm leaving the alum up because if enough decide to do alum we'll start that buy too.

[Blammer]

updated

[Mibo]

Please switch me from a 2 cavity aluminum to a 2 cavity brass GC
Thanks
Mibo

[Blammer]

done.

[Bert2368]

Is the brass buy still open, and if so, when is production likely?

[bwgdog]

Link to schedule in post #1

[Blammer]

yes the brass buy is still open, check in the first post for a link to the production schedule.

[Bert2368]

Thanks!

Looks like production would be next July? Decisions, decisions... Wait untill next year or plunk for that (possibly overpriced) Lyman 4 cav on swapping & selling right now???

[Dutch4122]

Please take me off the list for this group buy.

Thanks.

[Blammer]

updated post #103

[Ugluk]

A brass 2-cav GC please.

[Blammer]

updated

[Alchemist]

Fellas,

I'm dropping out of this one...this boolit is gonna work better for me I think.

http://www.castboolits.gunloads.com/showthread.php?t=134233

Blammer, PM coming.

[Blammer]

no problem Alchemist, all set

[8mm]

I'm in for a 2 cavity aluminum. Thanks

[Blammer]

updated post #109

[fatnhappy]

since this buy has enough participation in brass, the tooling and CNC work will go forth. Any chance NOE will cut the orders for aluminum moulds as well?

[Blammer]

not until there are 15 for the alum, as it required different tooling than the brass ones.

[Springfield]

I only want the brass OR the aluminum, not both. Still prefer the aluminum if I had the choice.

[Blammer]

roger on that Springfield, but the brass one is the only one with the go ahead at the moment.

[midnight]

Put me down for one Brass, 2 cavity, GC, drill for probe.

Bob

[Blammer]

updated post #113

[Springfield]

I've been experimenting with a similar bullet and this is just going to be too large for my use, so I am going to have to withdraw from this buy.

[Blammer]

updated

[Leonidas]

I'll take one - 4 cavity GC in brass

[Blammer]

updated post #119

[midnight]

Please change my order from 2 cavity brass to 4 cavity brass. Thanks

Bob

[Blammer]

done.

[chboats]

Blammer - since it looks like the brass version will be produced, you can take my OR off the alum. list

Thanks
Carl

[Blammer]

done.

[fatnhappy]

it certainly appears the only way to get this in a multi cavity mould will be going with the brass option. Blammer go ahead and move me over to a 4 cavity brass mould. No hollow points or other options.

Dean

[Blammer]

updated post #124

[Dschuttig]

Out of curiosity, why can't this be done with diameter options or RG?

[Blammer]

diameter options were tried with a few GB runs and it was very taxing and costly at the manufacturing end, so it was not very viable for the maker.

RG's are not available because the bullet is too light, it won't fall off of the pin, and since you can't take the pin out before opening the mould your just TUFF Puppy.

[Dschuttig]

I've had a few rifle molds converted to cramer type, and I know everyone hates that graphite spray, but it works really well on the hollow point pins. Both for release and cutting surface tension for even Hp cavities. Wondering about the size because I would love to use this in my oversize mil 30's but .312 is just a little to small, and my lyman 311290 cast just under .309, to small.

[dromia]

Darrell as the Brass is a runner put me down for a 4 cavity GC drill for probe. I'll still stay on the aluminium list, as I prefer the lightness of them, in the vain hope that it might at some point come off.

[Blammer]

updated post #129

[hotwheelz]

If its still open im game for a brass 2cavity no hp's

[Blammer]

updated

[wrench]

May as well throw my hat in the ring with this one...

2 cavity GC, aluminum, please.

[Blammer]

updated post #134

[sundog]

Blammer, I switched from aluminium to brass. Take my name off the aluminium list please.

[Blammer]

thanks! I forgot!

[fatnhappy]

bump.

[StrikerOmalley]

Blammer,

Please put me down for a 4 cavity brass GC mould (no HP, no probe).

Thanks,

[Blammer]

updated post #137

[happy7]

I will take a four cavity. Thanks.

[no34570]

Blammer
Could you please take me off the Aluminium buy and I'll take a Brass 4 cavity & drill for probe please?
thank you ;)

[Blammer]

Who wants what for BRASS.
All moulds are GC unless otherwise stated.

1. starbits 4C
2. bwgdog 2C
3. rugerfan 4C
4. chboats 2C
5. NYbushbro 2C
6. dominicfortune00 4C
7. Blammer 3C + HP; drill for probe
8. Ugluk 2C
9. Bcall ?C
10. adk mike 2C
11. semtav 2CPAID
12. bwgdog 2C (yep a second one)
13. ruger fan 1C +HP
14. sundog 4C GC PAID
15. mibo 2C
16. midnight 4C GC drill for probe
17. leonidas 4C
18. fatnhappy 4C
19. dromia 4C drill for probe
20. hotwheelz 2C
21.strikeromalley 4C
22. happy7 4C
23. no34570 4C drill for probe
24. rockrat 4C

[rockrat]

Much prefer an aluminum 5 cav. but that would be a long way out, so put me down for a 4cav GC Brass.

[Blammer]

updated

[Blammer]

updated post #144

[happy7]

my apologies. I found one of these in a lyman so I will need to back out of this mold. Sorry for the extra work, Blammer.

[Blammer]

no problem, glad you found a good one!

[DEVERS454]

I am in for a 2c brass with a single hollow point cavity.

I have set aside $$$ from the swear jar already. ;)

[DEVERS454]

And I want to go with gas checks on both cavities as well...

[Blammer]

updated post #146

[Blammer]

A striking new development!

Alum moulds will be offered in this also.

NOE has decided they will run it in alum, no sense haveing just the brass option. It would be NICE to have 15 or more in the alum but that is not necessary.

If you want to change from Brass to Alum, just post here and I will set it straight, and square the money difference too.

I have sent out a PM to those I saw were interested in an alum mould.

[Blammer]

updated #149

[no34570]

Blammer
I'll go back to Aluminum then, 3 cavity please & drill for probe please?
Later might add HP option,but will think on that ;)

[C1PNR]

Happy to hear this, I'm still in for a 4 C Aluminum with GC. Let me know when to supply $$.

Thanks to both Blammer and Al!;)

[Blammer]

updated on post #2

[dromia]

I'd like to change my order from a 4 cavity brass to a 4 cavity aluminium, drill for probe.

I'm so happy now, thanks Al.

[Blammer]

updated

[sundog]

Switch me back to aluminium, please.

[SwedeNelson]

Doing a update
Will try to keep all buys current on the schedule:
http://castboolits.gunloads.com/showthread.php?t=142415
If you have questions about our policy you can see it here:
http://castboolits.gunloads.com/showthread.php?t=156593

Bump

Swede Nelson

[starbits]

Well Blammer this thread was started 1 year ago tomorrow and we are all the way up to 20 molds. Chances of getting to 30 any time soon seems remote. The NOE schedule already extends to next year and this mold is number 15 of the unscheduled molds which adds another 7 months (July 2013) to that if nothing else changes. Any more popular mold that comes along bumps this mold back farther.

Any chance of having Miha do this mold instead of NOE?

Starbits

[RugerFan]

Sorry, but this new policy is way too convoluted for me. I don’t see this GB happening in a reasonable timeframe. Please pull my 2 mould orders from this list.

[SwedeNelson]

RugerFan
I'm sorry to see you pull out.
You have been one of our best customers.
And I'm very sorry this is such a mess.
But I have to try and do something or we will be gone.

Starbits
You would have been a new customer, just as sorry
to see you go too. A year is a long time and that is
what this is all about.

Again sorry to see you go.

Swede Nelson

[starbits]

Starbits
You would have been a new customer, just as sorry
to see you go too. A year is a long time and that is
what this is all about.

Again sorry to see you go.

Swede Nelson


Actually I do have one of your molds from the 243/6mm GB. I like the mold and certainly want NOE to stay in the mold business. Waiting a year for a quality mold from NOE isn't a problem either, although not ideal.

With the new policy however we could wait a year and find this mold in the exact same position as it is today - at least a year out and not any closer to being on the schedule. That is a problem. Especially if there are other quality mold makers who will schedule it.

I haven't gone anywhere - yet.

Starbits

[NYBushBro]

Yup... one year and counting. Pehaps Miha might do this (in brass) quicker...

I am a sucker for brass molds, but now that aluminum is being offered, I sense mutiny. Not holding my breath for this one to become a reality.

[RugerFan]

RugerFan
I'm sorry to see you pull out.
You have been one of our best customers.
And I'm very sorry this is such a mess.
But I have to try and do something or we will be gone.

Starbits
You would have been a new customer, just as sorry
to see you go too. A year is a long time and that is
what this is all about.

Again sorry to see you go.

Swede Nelson

Swede,
I realize that you are doing what you must to maintain your business. The uncertainty of delivery is my sole motivation for moving on. Your molds are excellent and I wish you much success.

[fatnhappy]

switch me back to aluminum please

[Blammer]

updated

[Leonidas]

Sorry, change of plans, please remove my order (#16).

[Blammer]

updated

[DEVERS454]

Switch mined to aluminum... thanks!

[BrassMagnet]

Sign me up for 4 cavity brass.

[fatnhappy]

DJ,

When you update the list please post a new one. I'm not certain which list you "updated."

It appears that when you switched me back to aluminum you spec'd a 4C for me. I want a 5C aluminum. Always have.

[Blammer]

updated

[mannyCA]

I need a 4 cav brass,solids, 2 with GC & 2 w/o.

[Blammer]

updated

[Mr Peabody]

I'm in for a 2 cavity aluminum GC

[Blammer]

updated

[Blackknight]

Hello,

Put me down for a 2 cavity aluminum.

Thanks,

Bob

[Blammer]

updated

[fatnhappy]

Is this ever going to come to fruition?

[Blammer]

I dunno, I hope so.

[wrench]

I did post an 'I'll take one' at post #125, but don't see myself on the list.
Let's change it, anyway...
One four cavity, aluminum, two cavities GC, two PB.
Thanks

[Blammer]

doh, sorry! I'll fix it

[semtav]

Guess we need to bump this to the top to see if we can get any more aluminum buyers.
I haven't been keeping track since last fall and thought we were on a September schedule. That must have changed with the aluminum re-addition

[no34570]

Another shameless bump,have to do it you know?
If I want these to go ahead,I have to create interest in them,hahaha ;)

[rockrat]

Blammer, put me down for whichever one will go in production first. I am down for a 4 cav brass, but if it looks like the alumnium on will go first, then change it to a 5 cav. aluminum. Thanks

[Blammer]

Will do!

[fatnhappy]

another bump

[chrisw]

I keep thinking of this one... How do you think she would do in a 308 Win?

Thanks!

[Shakey Jakey]

I'll go 2 cav brass

[Blammer]

updated

[Bert2368]

I keep thinking of this one... How do you think she would do in a 308 Win?

Thanks!
Um, maybe real well?

http://castboolits.gunloads.com/showthread.php?96037-Lyman-311290-Cup-Point

[chrisw]

Um, maybe real well?

http://castboolits.gunloads.com/showthread.php?96037-Lyman-311290-Cup-Point

cwillis at mail dot com brass 4c all GC 1HP and please drill for probe


LMAO, thanks Bert and Blammer!

[Blammer]

chrisw, don't expect an email, you won't get one, you'll get a PM when payment is due.

[chrisw]

chrisw, don't expect an email, you won't get one, you'll get a PM when payment is due.

Thank you, just habit...

BTW- are you getting any more .30 cal GC in soon? Thx!

[Blammer]

40,000 don't last long does it.. :)

yes, soon.

[Wayne S]

Put me down for a 5 cavity w/ GC's

[Blammer]

updated

[chrisw]

40,000 don't last long does it.. :)

yes, soon.

lmao, thanks!

[Wayne S]

Blammer / NOE, what is the OAL of this bullet from where the nose goes to .300 to the base ?

[Blammer]

well the nose is specified to .302 so it would be somewhere on the round part of the nose near the very front.

[Blammer]

updated

the gc's are not brass, they are copper

[Blackknight]

Hello Blammer,

I will have to drop out on this order, it will be a good boolit no doubt, but things have changed for me here. I am number 8 on the aluminum list. Thanks.

Regards,

Bob

[Blammer]

updated

[bwgdog]

Blammer-Now that order is 28-will it be moved up the list? tia

[Blammer]

It should be, NOE has updated his list recently but I haven't looked at it.

[davidaker]

Please put me down for a 2 cav alum GC.
Thanks

[Blammer]

updated

[Buzzard II]

Blammer,
Please put me down for one aluminum, 5 cavity, all GC, 1 HP, drill for probe. Thanks!
Bob

P.S. Will .30 cal gas checks be coming soon? I need 3,000. Thanks again! Bob

[Blammer]

updated

[bwgdog]

Take to top for more interest----

[DEVERS454]

I'm back in if this is still open.

2-cavity brass, 1 of them hollow point.

[Blammer]

yep still open, updated

[DEVERS454]

Please note, I want both of the cavities to be cut for gas checks.
Thanks!

[bwgdog]

Up to 30 orders-hope this comes up this summer!

[Trapaddict]

Still time to get in on this one??

[Blammer]

lots of time

[Trapaddict]

Please put me down for a 4 Cavity, Aluminum, All GC and Drilled for probe

Jeff

[Blammer]

updated

[Coltman]

Hi Blammer .. Please add me to the list for one 4Cav in brass + HP : Drilled for probe + .30 Cal Gas Checks .. Thanks Coltman

[Blammer]

updated

[Paulinski]

2 cavity brass please.

Thanks

[Blammer]

updated

[CATTLEMAN]

I'll take a three cavity Alum with probe hole: 1 gas check cavity, 1 plain base cavity and 1 gas check hollow point cavity.

I'd also like two extra pins.

Thanks

[Shakey Jakey]

I'm #17 (brass) please change me
to a 4 cav brass 3 GC 1 PB. Thanks

[Blammer]

updated

[DEVERS454]

Just realized I am on it for both brass and aluminum.

I would prefer just to have brass.

[Blammer]

updated

[Coltman]

Hi Blammer .. Please change my request to 1 brass mould 4 Cav W/ 3GC & 1 PB .. no HP .. drilled !! Thanks Coltman

[Blammer]

updated

[hylander]

Would this bullet function proper in an 03A3's Mag.
Would it be to big to chamber proper ?
I have not tried anything bigger than a 185gr. RN

[Blammer]

hylander, you may have better results asking this in the military section and a link to this thread.

sorry I cannot help with that as I don't know.

[no34570]

Blammer
Sorry,have to pull out of this one,my income has dropped dramatically,so have to re budget,sorry! :(

[Blammer]

no problem