225 55Gr. FN (MX3-22)

[SwedeNelson]

225 55Gr. FN (MX3-22)
THIS BUY IS CLOSED

http://i69.photobucket.com/albums/i80/swedenelson/1111-16322555GrFNMX3-22.jpg
HARRYMPOPE thanks for the samples.

Will get this buy on the schedule as soon as we get 15 orders.
We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.

This buy will be on our SB (Small Bore) moulds.
This is a down sized mould for better heat control.

Prices will be as follows:
Single cavity mould (Standard Size mould) $68.00 Ea.
Double cavity mould (2CSB) $72.00 Ea.
Three cavity mould (3CSB) $79.00 Ea.
Four cavity mould (4CSB) $85.00 Ea.
Five cavity mould (5CSB) $92.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $10.00
Prices are subject to change at any time.

You can mix number of cavities in an order to make 15.
We will offer gas check or plain base on this bullet.

Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal acount:
pbsco1@qwestoffice.net
Make checks and money orders out to:
Night Owl Enterprises

Our mailing address is:
Night Owl Enterprises
1645 W 150 N
Provo, Utah 84601
801 377-7289




Thank you for your interest in this buy.
Swede Nelson

[SwedeNelson]

List of orders
1 357 Voodoo 4 cavity GC
*2 Bodydoc447 5 cavity GC
*3 badbobgerman 5 cavity GC
*4 JerryV 2 cavity GC
*5 Wayne S 5 cavity GC
*6 shooter93 3 cavity GC
*7 BCall 5 cavity GC
*8 SmuvBoGa 3 cavity GC
*9 dromia 4 cavity GC drill for probe
*10 Bob Maerdian 4 cavity 2GC 2PB
*11 6.5 mike 3 cavity GC
*12 CWME 5 cavity GC
13 DragoonDrake 4 cavity 4GC
14 DragoonDrake 4 cavity 4PB
*15 dragonrider 2 cavity 1GC 1PB
16 Piedmont ? cavity GC
*17 PB234 5 cavity GC
*18 kirk miller 4 cavity GC
*19 excess650 4 cavity GC
20 RwBeV 4 cavity GC
21 Sewerman68 4 cavity GC
*22 MostlyOnThePaper 1 cavity GC w/HP
23 l h jenkins 3 cavity GC w/HP drill for probe
24 DaveInFloweryBranchGA 5 cavity GC w/HP (holding mould for payment)
*25 Fast Asleep 4 cavity GC
*26 easy ed 5 cavity GC
*27 drmaynard3235 4 cavity 2GC 2PB drill for probe digital therm. w/extra probe lead pot therm.
*28 bart55 5 cavity 3GC 2PB
*29 15bobcat 2 cavity 1GC 1PB drill for probe
*30 kennethF 4 cavity GC (will call at NOE)
*31 Ray H 2 cavity GC
*32 Hanish 5 cavity 1GC 4PB
*33 Pat I. 2 cavity GC
*34 Cariboo 2 cavity 1GC 1PB w/HP
*35 Frankenfab 4 cavity GC drill for probe
*36 cba257 3 cavity GC drill for probe
*37 fa38 4 cavity 2GC 2PB
*38 ohiochuck 5 cavity 3GC 2PB w/HP 1GC
*39 kirb 3 cavity GC
*40 Jhickdog 5 cavity 2GC 3PB
41
42
43
44
45
46
47
48
49
50


(*) = Paid

Thanks
Swede Nelson

[357 Voodoo]

I'm in for a four cavity

thanks

[tonyjones]

I'll take a 5 cavity. Drill for probe.

Thanks,

Tony

[Bodydoc447]

I'll take a 5 cavity all GC, please.

Doc

[badbobgerman]

im in for a 5 cavity .... awesome !

[Wayne S]

I'm in for a 5 cavity , this should suite my 1-12 twist Contender 22 Hornet bbls better that the heavier version.

[HARRYMPOPE]

5 cav

[shooter93]

I'll take a 3 cavity gas check.

[BCall]

5 cavity please!

[SmuvBoGa]

One three cavity with gas checks, pls.

Please drill for Temp Probe, if possible.

Thanks, JohnMc

[dromia]

Four cavity gas check, drilled for probe please. :cbpour:

[badbobgerman]

i count ten we need 5 more

[SwedeNelson]

Updated list
Bump

Swede Nelson

[DAFzipper]

Put me down for a 5 cavity all GC. Drill for probe.

[tonyjones]

We need 4 more.

[badbobgerman]

come-on guys this is an awesome light weight fn great for small game at lower vel. loads

[kirb]

I would like a 3 cav

Kirb

[badbobgerman]

3 more needed ... getting closer

[Bob Maerdian]

I'm in for a 3 cavity, I think.

Bob Maerdian

[tonyjones]

Two more (at least)!

[SwedeNelson]

Updated list

Thanks
Swede Nelson

[Cast of Thousands]

5 cavity GC please
Cast of Thousands

[tonyjones]

One more and we make the schedule.

Tony

[badbobgerman]

Put me down for another , a 5 cavity ... Just to get it on the schedule with the understanding i may back out if we get enough on board say 20 or more ok ? If this is acceptable to the honcho

MY GRANDSON, PRIDE AND JOY MY NEW AVITAR PIC.

[badbobgerman]

Bump to top , and put on the schedule please

[Wayne S]

[smilie=w::bigsmyl2:[smilie=w::bigsmyl2: and NOW the wait begans

[SwedeNelson]

Updated list
Got us on the scheduale - Thanks badbobgerman

Swede Nelson

[badbobgerman]

Updated list
Got us on the scheduale - Thanks badbobgerman

Swede Nelson

It will be my pleasure ..

[6.5 mike]

I'm in for a 3 cavity g/c'ed.

[CWME]

5 Cavity GC please

[DragoonDrake]

I am in. 4 cavity: 2 gas checked and 2 plainbase.

Thanks,
Adam

[RwBeV]

Is it to late to get in on this, this is the first time I have tried this so I'm not sure what I need to do. But I would love to get my hands on a four cavity mold. If some one would let me know I would be grateful.

Bob

[tonyjones]

Bob,

This one is scheduled for production in April so there's plenty of time to get in. Post here "I want a 4 cavity". Look through the order list to see if there are any options that you might want/need. Swede will close the buy a couple of weeks before production and will send a PM to everyone on the order list to request funds. I hope that helps.

Regards,

Tony

[RwBeV]

Thats what I needed to know

Put me down for a 4 cavity

Bob

[badbobgerman]

its not too late unless there is a post stating .. this buy is closed ..., even then some extra's are made and sold on the vendors list , hopefully .when made.... just state ill take one 4 cavity and the honchos will add your name to the list ... they will ask for payment shortly before production

[badbobgerman]

nice mold good for all around hunting fn will hit em hard

[castblaster]

5 cavity GC please

[uncleskippy]

I will take a 5 Cavity GC

Thanks

[dragonrider]

OK I am in for 2, 1 GC and 1 PB

[Piedmont]

I'm in. Let me wait to tell the exact configuration until money is due because I know I'll change my mind in the interim.

[PB234]

Please include me for a 5 cavity gas checked mold, thanks for your effort

[castblaster]

Castblaster 5c GC

[Kirk Miller]

Please put me down for a four cavity GC
Thanks

[excess650]

Swede,
Put me down for a 4 cavity all GC. Thanks!

[RwBeV]

I just realized that I said just a 4 cavity it needs to be a 4 cavity "GC" please.

Bob

[SwedeNelson]

Updated list.
Bump

Thanks for the orders!
Swede Nelson

[jerryv]

I'll take a 2 cavity

[Cast of Thousands]

I regret I must cancel my order for this mold

Cast of Thousands

[Wayne S]

OPPS, wrong mold

[badbobgerman]

Put me down for another , a 5 cavity ... Just to get it on the schedule with the understanding i may back out if we get enough on board say 20 or more ok ? If this is acceptable to the honcho

MY GRANDSON, PRIDE AND JOY MY NEW AVITAR PIC.

moneys tight ill have to back out of one mold so remove line 4, or 5 please . we now have 25 on board im exited to get one of these looks like early next year ... plrase only remove 1 of these from the list
l

[SwedeNelson]

Updated list.
Bump

Thanks
Swede Nelson

[sewerman68]

If its not too late I would like a 4 cavity gc, thanks.

[DragoonDrake]

Hey Swede, I would like to alter my order.

2 molds both 4 cavities, one plainbase and one gas check.

[SwedeNelson]

Updated list
Bump
You can check the scheduale here:
http://castboolits.gunloads.com/showthread.php?t=130122

Swede Nelson

[chuck4570]

Im in for a 5 cavity GC !

[l h jenkins]

i would like a 2 cavity in brass gc drilled for a probe one hp. if brass is not possible 3 cavity in alu. with probe and hp. thank you

[castblaster]

Please take me off the list. Thank you, Matt


Matt Hooper

[Roger Ronas]

5 cavity GC please

[DaveInFloweryBranchGA]

5 cavity GC please

[Roger Ronas]

Can someone tell me what the diameter of the GC stem is?
Thanks
Roger

[SmuvBoGa]

According to the diagram - 0.225.

[Roger Ronas]

Thanks for the reply, but that is the back drive band dia. the stem is a little smaller. I've researched more and have the generic answer I need.




According to the diagram - 0.225.

[Fast Asleep]

I'll take a 4 cavity.

Thanks,
Tim Janke

[Fast Asleep]

OOPS--forgot to say all GC

[SwedeNelson]

Updated list
Bump

Thanks for the orders
Swede Nelson

[drmaynard3235]

AL
I'm in for a 4 cav, 2 PB 2 GC. Drill for probe.
1 digital casting thermometer with extra probe.
1 lead pot thermometer
drmaynard3235

[easy ed]

Please put me down for one 5 cavity with gas check.

Thanks

Easy Ed

[Bert2368]

I'm interested- Is there a design discussion thread somewhere on this one? The link in the first post seems to be broken-

[uncleskippy]

Swede,

I hate it, but I am going to have to drop out of this group buy.

[Mark85304]

I'll take a 5 cavity GC.

[SwedeNelson]

Updated list
Bump

Thanks
Swede Nelson

[MostlyOnThePaper]

I'd like a 3 cavity gas check mold please.
Thanks!
Randy

This should be just the ticket for my. 219 Wasp. :-)

[chuck4570]

Sorry, I must pull out of this one guys.

[SwedeNelson]

Updated list
Bump

Swede Nelson

[bart55]

put me in for a five cavity three gc and two pb

[SwedeNelson]

Updated list

Bump

Just so we have no misunderstandings this
buy is on the schedule for July 2012

Thanks
Swede Nelson

[tonyjones]

Please remove me from the list.

Tony

[DAFzipper]

I have to back out on this one. Please remove me from the list. DAFzipper

[Piedmont]

I now know I want mine to be a 4 cavity gas check.

[SwedeNelson]

Updated list

Bump

Thanks
Swede Nelson

[badbobgerman]

money sent #3 on the list sent today via pay-pal for a 5 cavity sent 106$

[mikes farm]

The link to the discussion seems to be broken.
Does someone have a different link ? I have a Encore .223 pistol that I am interested in shooting this in. Is there a discussion about this ? I am only looking to shoot this at 50 yards and not looking for blistering speed. Would these conditions still require a GC ?
Regards
Mike

[badbobgerman]

im not going to use a gas check until i reach 1800 fps this is where i think the check is needed
that is a little faster than 22 rimfire speeds ... , no checks needed there

[HARRYMPOPE]

im not going to use a gas check until i reach 1800 fps this is where i think the check is needed
that is a little faster than 22 rimfire speeds ... , no checks needed there

if you shoot hard metal like Linotype that works fine.Up to 50 yards anyhow.My good buddy tried the no GC thing and got to 2800 without leading in 22's but accuracy degraded badly.At 1600 it shot about 1.5" at 50.

I'd be curious how yours does.

George

[KennethF]

Add me to the list for a 4 cavity GC.

Ken.

[15bobcat]

I'm in for a 2 Cavity 1GC 1PB & Drill for probe please. Pay-Pal sent.

Thanks
-Harold

[Bob Maerdian]

Hello Swede Nelson,

Received a mold from you the other day; #225 62 gr FN. It is an MX-3 22 design 3cavity mold. I don't remember ordering this mold from you so I checked on the list of orders. I am listed as #35, so I checked the requests and # 35 is for a fellow named Felix. I'll keep the mold and pay you for it. I have ordered MX-3 22 a 55 gr FN, I requested a 3 cavity all gc, I WOULD LIKE TO CHANGE THAT TO 4 CAVITY (2 pb and 2 gc) I did send a check for the 3 cavity 55 gr FN MX-3 22, I will send a check with the additional balance, if that is OK.

I have also ordered .311 165RF (RD) in 4 cavities (2pb and 2 gc). I have not sent a check for this mold as yet. If you could let me know What I owe you for all this I will send you a check straight away.

Thank you for your fine molds,

Bob Maerdian (kossuth@pacbell.net)

[SwedeNelson]

Bob

Have your letter and its for a MX3-22-EX 63Gr.
paid with a check dated June 4 2011

Sorry for the mix up.
Will PM you some more information.

Swede Nelson

[Hamish]

Al, I would like:

Hamish 5 cavity 4 PB 1 GC 225 55Gr. FN (MX3-22) GB 108 December 33

Thank you sir.

[Pat I.]

Could you put me down for a 2 cavity gas checked.

[Bert2368]

I would really like to review the discussion thread mentioned in the original post-

The link is broken, and I have not been able to find it by searching the site, some others have asked about this as well- is it gone forever?


225 55Gr. FN (MX3-22)
Here is the link to the discussion thread:
http://castboolits.gunloads.com/showthread.php?t=106634

http://i69.photobucket.com/albums/i80/swedenelson/1111-16322555GrFNMX3-22.jpg

[Pat I.]

A quick question. Are the dimensions on this print drawn for WWs? I've searched around a bit but can't find the answer.

[SwedeNelson]

Bert2368

Sorry - I have tried to find it to, but it looks like it has been removed.
I have no control over it.

Pat I

Yes - WW material
And I have you on the list just havent updated the thread.

Swede Nelson

[Pat I.]

Thank you Swede.

[Cariboo]

Could you put me down for a 2 cavity with 1PB & 1gas checked HP

thanks

[frankenfab]

I would like a 4 cavity gas check, drill for probe, please.

[jixxerbill]

id like to get in on this also please.. 4 cavity gc. thanks

[Plinkster]

Please put me down for a 5 cavity all gas check.

[MostlyOnThePaper]

Swede,
Can you change mine to a single cavity and add the hollowpoint option?
Thanks!
Randy

[Plinkster]

Disregard my post Swede, I just bought a mold from you that will work for me thanks for the quick shipping!

[badbobgerman]

05-31-2012, 07:34 PM #82
badbobgerman
Boolit Master




Join Date: Oct 2010
Location: west coast U.S.A. , foothills
Posts: 954 money sent #3 on the list sent today via pay-pal for a 5 cavity sent 106$
__________________
To disarm the people is the best and most effectual way to enslave them.”
~George Mason

my feedback page:click and give me feedback here,below...

http://castboolits.gunloads.com/show....php?p=1412368
please mark me paid

[SwedeNelson]

badbobgerman

Got it - thanks for the reminder

Swede Nelson

[cba257]

I'll take a 3 cavity all GC and drill for probe please.

[FLYCUTTER]

I'd be in on this if Swede could cut this in a 10 cavity

[Patrick L]

How does this boolit do in a 1 in 9 twist Colt HBAR. Any feeding issues due to the flat nose?

Is there till time to get one?

[SwedeNelson]

Updated list

Bump

FLYCUTTER
Can do - it will be a 2 sided 5 cavity.

Patrick L
Hope some one that has used it will chime in.
This is a first for me. Sorry

Swede Nelson

[Wayne S]

I'd be in on this if Swede could cut this in a 10 cavity

Al,
What would be the cost of one of these 10 cavity set ups ?
Wasn't this 10 cavity set up offered on the 225-55FN ? how many were made ?? and did you get any feed back on how well they worked; ie "% of "keepers"

[Nix]

Please put me down for a 5-cavity with handles.

[SwedeNelson]

Nix

Got you on the list.
Sorry - no handles

Swede Nelson

[kirb]

Please remove me form list (11 kirb 3 cavity GC)

Thanks
Kirb

[doctorggg]

Put me down for a 5 cavity gas check mold please.

[fa38]

I would like a 4 cavity mould. 2 GC and 2 PB

Just received the 2 cav mx3 62 gr. mould yesterday. I cast a couple hundred bullets this morning and they look great. Thanks.

[Nix]

Sorry but I need to cancel this order; just bought a swaging press and dies for .223. Thanks

[HARRYMPOPE]

Pat- my sample to Swede was cast of Linotype i believe.

[DaveInFloweryBranchGA]

Where is this mold on the schedule? I got the other .224 mold, but was wondering about this one.

[Wayne S]

Where is this mold on the schedule? I got the other .224 mold, but was wondering about this one.

look at the "STICKY" at the top of this section ,the one that says


" NOE Group Buy Index and Delivery Schedule"

[Nix]

Hi Swede,

I left a message previously but I think you may have missed it; please cancel my order as I bought a swaging press for my .224 needs, thanks.

[DaveInFloweryBranchGA]

Hi Swede,

Can I add this to my mold at this late date?

"Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra."

If so, I'd like to do so. Gonna be doing some hog hunting it would appear at ranges this bullet ought to be perfect for.

Dave

[DaveInFloweryBranchGA]

look at the "STICKY" at the top of this section ,the one that says


" NOE Group Buy Index and Delivery Schedule"


Thanks Wayne, I'll check it out. Obviously, I've been off the board for a while, all this newfangled information available for everything. I feel I've missed out while I was working on my boat.

Dave

[FLYCUTTER]

Please take me off the list because I purchased a 62 gr. 5 cav. off of Swedes web site.
Thank You

[Mark85304]

Sorry, I have to drop out of this GB.

16 mark85304 5 cavity GC

[SwedeNelson]

Updated list

Bump

Thanks
Swede Nelson

[fullofdays]

will this flat nose design function in a 5.56 AR or will I need the Saeco 221 Round Nose design?

http://noebulletmolds.com/orders/catalog/product_info.php?cPath=24&products_id=87

[SwedeNelson]

Checked list

Bump

fullofdays

I have had no experience with this one
Maybe HARRYMPOPE can give us some insight

Swede Nelson

[doctorggg]

I too would like to know if this will function in an AR? If not I don't need it.

[HARRYMPOPE]

will this flat nose design function in a 5.56 AR or will I need the Saeco 221 Round Nose design?

http://noebulletmolds.com/orders/catalog/product_info.php?cPath=24&products_id=87

Being that the bullet is tapered quite a bit it may be the best for magazine loading. If seated long to engage the throat it will only be held by the rear band. It's at its best seated long to engage the throat in a bolt action. If seated deeper it will be at a diameter that is under .225 and may not have enough neck tension(at the case mouth) and may wiggle arround and not be very concentric.It is my opinion standard two diameter bullets like the SAECO 221 or RCBS 55 SP is a better option. Those are the two I have used n AR15's anyhow.

George

[doctorggg]

Thank you very much for that information George. Merry Christmas to you. Greg

[Piedmont]

Please take me off the list for this one. I was able to buy a couple of molds while waiting.

[SwedeNelson]

This is a last call on this one
Get your order in if you want one
Will close Thursday the 20th
Will start sending out PM's for payment next week

Thanks
Swede Nelson

[doctorggg]

Please drop me from the list. #41

[jhickdog]

Hey Swede, add me for a 5 cavity mould. 3 pb and 2 gc.

Thanks
Jhickdog

[ohiochuck]

Hi!
Can anyone tell me if this design will work well in a bolt .221 Remington or are other designs possibly better. I currently have several molds lighter than 55 g.
Thanks!
Jim

[HARRYMPOPE]

I have shot it in 1-14 222's and it should also be a wonderful bullet for the 221 FB. It shoots better than the SAECO 221 and the RCBS 55 SP in my 22-250 and 222's.

George

[ohiochuck]

HI
I will take a 5 cavity mold 2 PB; 2 GC & 1 GCHP
I mailed the money order to you today, Dec.18,2012.
Thanks!
Jim

[kirb]

put me down for a 3cavity gas check

Kirb

[SwedeNelson]

This buy is closed
Will be on the mill next week

Thanks for the orders
Swede Nelson

[Bodydoc447]

Al, please double check your payments. My check for this one cleared your bank on 12/31.

Thanks,
Doc

[SwedeNelson]

Start shipping today

Bodydoc447
Got it, just a little slow posting it.

Swede Nelson

[Bert2368]

If there are any extra, I'd love to hear about it- was out of the country for a bit and just catching up.

[SwedeNelson]

This buy is closed and over.
All paid orders are shipped.

Thanks to all that participated.
Swede Nelson

[CWME]

Awesome, I thought this got bumped to Feb based on the schedule but good to hear it is in the mail! I look forward to getting some of these down range!

[Bodydoc447]

Got the mould today, Al. Another work of art. You are truly on a roll.

Thanks for everything,

Doc

[badbobgerman]

+1 , got mine today also... nice workmanship ! thanks swede , and harry m pope for making this possible...badbob

[MostlyOnThePaper]

Got mine today, it's a beauty!
+1 on the thank you's.

Randy