NOE 358477 150Gr. SWC

[SwedeNelson]

358477 150Gr. SWC
Here is the link to the discussion thread:
http://castboolits.gunloads.com/showthread.php?t=95418

http://i69.photobucket.com/albums/i80/swedenelson/1111-158358477150GrSWC.jpg

http://i69.photobucket.com/albums/i80/swedenelson/1111-158358477150GrGCHPSWC.jpg

Will get this buy on the schedule as soon as we get 15 orders.
We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.

Prices will be as follows:
Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.
RG2 cavity HP mould $96.00 Ea.
RG4 cavity HP mould $126.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $10.00 Shipping/Handling.
Prices are subject to change at any time.

You can mix number of cavities in an order to make 15.
We will offer Gas Check or Plain Base on this bullet.

Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal account:
pbsco1@qwestoffice.net
Make checks and money orders out to:
NOE Bullet Moulds

Our mailing address is:
NOE Bullet Moulds
1645 W 150 N
Provo, Utah 84601
801 377-7289




Thank you for your interest in this buy.
Swede Nelson

[SwedeNelson]

List of orders
*1 357 Voodoo 4 cavity PB
*2 Bodydoc447 5 cavity PB
*3 Love Life 4 cavity 4PB
*4 Love Life RG2 GC
*5 376Steyr 5 cavity PB
6 Muleshoe Slick 4 cavity GC
*7 UnderDawgAl 5 cavity 1GC 4PB
8 DiamondD RG4 PB
*9 milbo 3 cavity PB
*10 kirk miller 5 cavity PB
11 hollow-point RG4 GC
*12 Shome10x 4 cavity PB
*13 sffar 5 cavity PB drill for probe
*14 Bill*B 4 cavity GC
*15 james wisner 4 cavity PB
*16 nicholst55 4 cavity PB
17 taminsong RG4 GC
*18 par50 5 cavity PB
*19 trmungle RG2 PB
*20 Hardcast416taylor 4 cavity PB
*21 9.3X62AL 4 cavity PB
*22 GRS1 5 cavity PB
23 Shawnsmc 5 cavity PB
24 blaser.306 5 cavity PB
25 Lucas RG2 PB
26 Lucas 2 cavity PB
*27 huntnman RG4 PB
*28 shedhunter RG2 PB
*29 smlkid 5 cavity PB
*30 tudor8055 RG2 PB
31 johnny356ER 4 cavity PB
*32 maximumbob54 RG4 PB
*33 ratboy 4 cavity PB
*34 jethunter RG4 GC drill for probe
*35 41cal 5 cavity PB drill for probe
*36 CBH 5 cavity PB
*37 nooneimportant RG4 PB
*38 slide RG4 PB
*39 hcr RG4 PB
*40 fullofdays 5 cavity PB
41 101 coolcars 5 cavity PB
*42 HighHook RG4 PB
*43 ColColt 3 cavity PB
*44 Dschuttig RG4 PB
45
46
47
48
49
50


(*) = Paid


Thanks
Swede Nelson

[SwedeNelson]

This is a list of interest to run brass moulds
We would need 15 orders to run.

The prices would be as follows
Single cavity brass mould $90.00 Ea.
Double cavity brass mould $94.00 Ea.
Four cavity brass mould $111.00 Ea.
RG2 cavity HP brass mould $118.00 Ea.
RG4 cavity HP brass mould $152.00 Ea.

List of orders
*1 357 Voodoo RG2 PB
*2 H.Callahan RG2 PB drill for probe
3 That'll Do 4 cavity PB
*4 tinsnips 4 cavity PB
*5 ddixie884 4 cavity PB
*6 pbhurler 4 cavity PB
*7 NebraskaCAK 4 cavity PB
*8 Moonman 4 cavity PB
*9 454gene 4 cavity PB
*10 376Steyr 4 cavity PB
*11 Joe Bob RG2 PB
*12 bradbn4 RG4 PB drill for probe
*13 IIJSavoy RG4 PB
*14 skimmerhead 4 cavity GC
15
16
17
18
19
20

(*) = Paid


Thanks
Swede Nelson

[357 Voodoo]

swede put me down for a 4 cavity al and a rg2 brass all pb

thanks

[Bodydoc447]

Please put me down for a five cavity PB in Al blocks.

Thanks,

Doc

[tonyjones]

Al,

I'll start off in the brass column with:
1-4 cavity and 1- RG4; drill both for temp probe.

Tony

[Love Life]

I'm definately in on this one.

Put me down for a 4 cavity PB in aluminum blocks please and a RG2 PB also in aluminum blocks

Thanks,
Dick

[H.Callahan]

Ok, I will go with a brass RG2 (the pins are reversible, right?), PB, drill for thermometer.

[376Steyr]

I'll take a 5 cavity PB, in Aluminum. Thanks!

[UnderDawgAl]

I'm in for a 5-cavity aluminum. 4 PB + 1 GC, none of them HPs. Thanks!

[DiamondD]

I would like one RG4 PB please.

[Muleshoe Slick]

Put me down for a 4 cavity, with GC

[Love Life]

DiamondD and Muleshoe Slick- What mould material did you want those in? Aluminum or brass?

[Muleshoe Slick]

Aluminum is fine for me.

[That'll Do]

I would be interested in a 4 cavity BRASS mold.

[Love Life]

Bump to top

[H.Callahan]

BTT

So where is everyone that expressed interest in the original thread?

[Mibo]

I would like a 3 cavity aluminum all PB

[Kirk Miller]

I'll take either a 5/cav al. or a 4/cav brass. All plain base. Which ever comes online first.
Kirk

[UnderDawgAl]

We're halfway there on the Al mould.

[Muleshoe Slick]

bump to top

[That'll Do]

I'm surprised more folks haven't joined in on this group buy. This bullet is a great one, very versatile in both 38 Special and 357 Magnum.

Come on folks, you know you want one (or two).

I'm hoping we get enough people signed up for both the aluminum and brass versions. I prefer brass, but if it comes down to it, I'll go with aluminum if means getting enough people to complete the GB.

[tinsnips]

I will take a 4 cav. PB brass.

[H.Callahan]

To the top with thee!

[SwedeNelson]

Up-dated list
Bump

Swede Nelson

[hollow-point]

i would like RG4 GC. hp thanks and a three cavity PB/ alum. is fine

[Love Life]

WooHoo! Almost there on the aluminum side of the house.

[Love Life]

To the top. Come on gents. You know you want one... or two.

[Shome10x]

I'm in for this one also....4 cavity pb...

Thanks,

shome10x

[tonyjones]

Swede,

Please change my order to aluminum:
One-5 cavity, PB, drill for probe
One-RG4, PB, drill for probe

That should get the aluminum mould orders to 15 and get this one in the schedule. By the way, have you updated the schedule recently? If so, I haven't seen it.

Thanks,

Tony

[sffar]

What the heck, I'll take an RG2 PB aluminum.
Thanks,
Sam

[hollow-point]

swede is it possible to remove 3-cavity plain base from this run?

[SwedeNelson]

Updated list
Have 15 so we are on the schedule.

Thanks for the orders and keep-em coming.
Swede Nelson

[H.Callahan]

I would like to hold out for the brass for a while. How long do we have to make a final decision to jump ship to aluminum?

[Bill*B]

I'll take a 2 cavity Al block GC base, and if possible cut it a tad small, so it drops at .358" or just a bit over.
Regards, Bill*B

[SwedeNelson]

H.Callahan

We have some time.
It would be great to run both Brass and Aluminum!
11 more brass and we can do it.

Swede Nelson

[H.Callahan]

It would be great to run both Brass and Aluminum!I totally agree. Actually, I can't understand why more people are not wanting this in brass.

I might eventually defect to the dark side, but I REALLY would like to get a copy of this in brass.

[Love Life]

No shame in this bump. This is a great 38 special and 357 Mag boolit.

[James Wisner]

Sign me up for a 4 cavity Alum. plain base mold.

Jim Wisner

[ddixie884]

4 cavity brass, plain base, please.............

[nicholst55]

What is the anticipated 'run' date for this mold? I hafta count my pennies, you know...

[sffar]

The NOE schedule thread . .
http://castboolits.gunloads.com/showthread.php?t=83330
Looks like January

[nicholst55]

I'm in for an RG4 plain base, in aluminum; I'll have it shipped to Maryland.

I've got a single-cavity Lyman mold in this design; it shoots great, but it's definitely on the S-L-O-W side!

[UnderDawgAl]

To the top for what should be a nice boolit.

[PbHurler]

I'm in for a 4 Cavity Plain Base Brass

[SwedeNelson]

updated list
Bump

Thanks
Swede Nelson

[taminsong]

Swede,

I would like an RG4 gas check, but I want to know when you are going to
collect the money for this.

Thanks.

[sffar]

The NOE schedule thread . .
http://castboolits.gunloads.com/showthread.php?t=83330

[357shooter]

I'll take a 5 cavity plain base, aluminum.

[trmungle]

I would like a 2 cav. H.P. mold. Thank you, Tom

[trmungle]

What does RG mold mean? thanks, Tom

[tonyjones]

Rube Goldberg.

[trmungle]

I see Swede lists a RG2 & RG4 mold. I would like to know the diff. in these molds and the reg molds. Tom

[357 Voodoo]

Tom, the RG moulds are a 2 and 4 cavity hollow point mould where all cavitys are hp'd with captive pins. They will make a mess of hp'd boolits in a hurry.

here is a pic that Sweede posted for one of his other moulds that shows the rg2&4.
http://i69.photobucket.com/albums/i80/swedenelson/452250GrRFMould002.jpg

[trmungle]

Thank you 357. Tom

[trmungle]

Hi Swede, I want the RG2 cav. mold. Thank you, Tom

[taminsong]

sffar,

Thanks for the link. Am afraid he will collect the money soon.

Swede,

I'm in one RG4 - GC.

[sffar]

taminsong,
Payment's requested about the time the mold's are scheduled to get made, so you've got a few months to save up.
Sam

[JBL]

Wrong post I thought I had the 360160 Double Crimp Groove SWC Group Buy , please diregard below

I need one RG4 cavity HP mould with gas check & one 5C plain base mold

[par50]

--------------------------------------------------------------------------------

Please put me down for a five cavity PB in Al blocks.

[sffar]

Please change my mold to a 5C PB aluminum. Thanks.
Sam

[trmungle]

I do not see my name on the list. I want a rg 2 plain base mold. Thank you, Tom

[mick27]

hi swede,

please put me down for a RG2, plain base.. in aluminum

thanks,
mick27
mick jones
08560

[NebraskaCAK]

Figured I'd make my first post a good one....
Please put me down for a 4C PB brass

Thanks

NebraskaCAK

[Bill*B]

Please change my order to an aluminum 4 cavity GC, cut a little small (.358"). Regards, Bill*B.

[mick27]

swede,

please withdraw my order, for this mold..

thanks,
mick27

[SwedeNelson]

Updated list
Bump

Thanks for the orders
Swede Nelson

[nicholst55]

I need to change mine to a plain 4 cavity aluminum mold.

[9.3X62AL]

If there's still time to subscribe.......I would like an aluminum 4-cavity mould, no hollow point or gas check modifications. My Lyman 2-banger version of this classic has about had it, after 30+ years, and I'd like to sample Al's work after all the great reviews his tools have received. My first Group Buy participation, too--though I've bought a couple "leftovers" and "over-runs".

Thank you!

Allen Paine

[Hardcast416taylor]

If this is still open I`ll take a 4 cavity plain base solid nose mould.Robert
Aluminum mold construction please.

[Hardcast416taylor]

Have I missed this GB or is it still open to "wants"?Robert

[SwedeNelson]

Hardcast416taylor
This one is on the scheduale for February

Updated list
Bump

Swede Nelson

[9.3X62AL]

Thank you, sir! Standing by and looking on.

[ddixie884]

I'm on the road a lot PM me with info when it is time to pay....THANX

[GRS1]

I'll take a 5 cav. plain base in aluminum please

[SwedeNelson]

Updated list
Bump

Swede Nelson

[MT Gianni]

Please put me down for an RG2. Thanks, Gianni.

[Love Life]

And the list keeps on growing. With my PB check maker I'll have these bad boys screaming!

[9.3X62AL]

It is a good boolit design that has done well for me in 38 Special and more recently in a tight-sized Colt Police Positive in 38 S&W. I don't recall ever running it in 357 Magnum, though. #358156 and #358430 got the nod for the heavier caliber, and still do.

[LouisianaMan]

I'd like an RG 2 plain-based, aluminum. These HP's should be beautiful in my .38 S&W's!

9.3 x 62AL: the 38 S&W bug still bites, doesn't it?? Would be interested in any info you're willing to share on what alloy, powder and velocities you have run successfully in this caliber, so please PM me if convenient.

[SwedeNelson]

Updated list
Bump

MT Gianni
Do you want GC or PB?

Thanks
Swede Nelson

[Moonman]

Swede,
Please put me down for a 4C PB Brass if you could.
MOONMAN

[MT Gianni]

Swede PB please.

[SwedeNelson]

Updated List
Bump
You can check the scheduale here:
http://castboolits.gunloads.com/showthread.php?t=130122

Swede Nelson

[454gene]

Please put me down for a brass 4 cavity PB.
This will be my second mold after casting for the first time last week with a Mihec brass 200 gr SWC. I shot Bullseye and like to drag a revolver to a match for a change.

[LouisianaMan]

Hi Swede,
Sorry, but I need to hold off on this one after all (see post #80), so please remove me from the list. Wouldn't do this to you on short notice or otherwise endanger the success of the GB--I certainly appreciate the fine work you do and the comradeship here on CB.
Thanks,
LAMan

[shawnsmc]

Put me down for a five cavity aluminum please.

[blaser.306]

Might as well put me down for a 5 cavity PB (DFP) Thanks for all your work thru the year and merry X-as to you and yours from all us members up here in the frozen north.

[Lucas]

Hi Swede,

If still open, could you please put me down for:

RG2 HP Plain base, 150 gr, aluminum

Thank you sir.

[IIJSavoy]

If not too late, I'd like to get in on this one.

RG4 Plain Base, Aluminum

Please let me know and thanks.

[SwedeNelson]

Updated list
Bump

Thanks
Swede Nelson

[MT Gianni]

Swede please remove me from this buy as I am in on the 360160 leftover RG2. If that falls apart for any reason, keep me on this one. Thanks, Gianni.

[SwedeNelson]

Checked list
Bump

Swede Nelson

[huntnman]

If still open would like RG4 pb.Thanks Greg

[SwedeNelson]

Updated list
Bump

Thanks
Swede Nelson

[376Steyr]

I would also like a BRASS 4 cavity PB. Please add me to that list as well. If we somehow got to 15 brass moulds before the aluminum buy closes, would they run at the same time? Or would the brass go to the end of the schedule? Thanks!

[Lucas]

Hi Swede,
Could you also please add a 2 cavity PB solid mould for me. I know I am on for a HP as well. Thank you sir!

[Shedhunter]

Put me down for a RG2 plain base aluminum. Thanks

[smlekid]

Hi Swede Put me down for a 5 cavity Aluminium PB please If still open

[tudor8055]

I would like an RG2 PB aluminum.

[johnny356ER]

Swede,

I would like a 4 cavity Aluminum all PB.

Thanks,
johnny

[Maximumbob54]

Can I sign up for this:

"RG4 cavity HP mould $126.00 Ea."

Aluminum please. Can it be made Plain Base? If not then I would still like it.

[ratboy]

i would like a 4 cavity plain base in aluminum please sir.
payment was sent via paypal

[SwedeNelson]

Updated list
Bump

376Steyr
We would run them together.

Thanks
Swede Nelson

[SwedeNelson]

Bump
We are about 3 to 4 weeks behind.
Will get a PM for payment out in about 2 weeks.

Swede Nelson

[9.3X62AL]

That's cool, Al. Thanks for the updated info.

[ratboy]

i hope it doesnt create a problem sending my payment early. i wanted to make sure it was done before i ran out of monies.
:mrgreen:

[jethunter]

Please sign me on for one RG4 GC, drilled for probe.
Does NOE sell gas checks?

Payment by paypal, shipping to Canada.

[skimmerhead]

please put me down for an rg4 gc with extra set of blank pins, aluminum. thanks

skimmerhead

[Love Life]

Can I get my 4 cavity mould changed to all plain base? Last change I swear.

[JoeBob]

Please put me down for an RG2 Plain Base Brass.

If the brass doesn't get enough to run I'll take Aluminum RG2 Plain Base.

Only 4 more to run BRASS!! C'mon, you know you want one...or two.

Thanks,sid.

[SwedeNelson]

Updated list
Bump

Thanks
Swede Nelson

[41cal]

I'm in, Put me down for a 5 cavity pb alum and drill for probe. Thanks

[CBH]

I'll take a 5- cav. PB alum. please, Thanks

[nooneimportant]

I'll Take one.

RG4 cavity HP mould Plain Base bullet. aluminum $126.00

[slide]

I'll take an RG-4 HP plain base. Thanks.

[slide]

I forgot, aluminum, sorry

[hcr]

Please put me down for a RG4 Plain Base in Aluminum. I will send payment this week. Thanks hcr

[bradbn4]

RG4 cavity HP brass mold - PB, drill for thermometer
If pins are not reversible - set of blank pins

Note: The link is dead referencing the discussion.

Both HP and non HP show 150 grains - is that correct?
There is no overall length on the second picture for HP - I "assume" it's the same overall size because it's basically the same mold configured to accept the pins.

[fullofdays]

I'll take a 5- cav. PB alum mold as well please...

[101coolcars]

I would like a 5 cav plain base in aluminum.

Thanks
Terry

[PbHurler]

Pleeeeeeeeeease,
We only need 4 more to get this run in brass

[bradbn4]

Pleeeeeeeeeease,
We only need 4 more to get this run in brass

There is some hope; It looks like my request 119 has not made it to the list.

[UnderDawgAl]

Swede,

Dropped a check for $102.00 in the mail today. I'm #7 on your list of orders.

Regards,
UnderDawgAl

[SwedeNelson]

Updated list
Bump

What the heck -
I'll get a order in for the brass tooling.

Thanks for the orders
Swede Nelson

[IIJSavoy]

Since you're going to do the mold in brass anyway, can I bump to the brass mold.

I'm number 30 on the AL mold list.

Let me know...

[454gene]

I'm on the list for the brass and alum. molds as it seemed the brass mold was dead.Would prefer a brass one if it's not a problem. Will accept either one without any reservations.
Thanks

[ddixie884]

Swede, If you don't get 15 for brass I will take an Xtra to help out, OK. THANX.............

[H.Callahan]

Ok, I am confused. Are brass going to actually get done? I kinda dropped away from this thread because I didn't think we were going to get enough for brass.

If we ARE doing brass, then when? Do I need to get my money in?

[skimmerhead]

please change my order to a 4 cav solid gas check brass instead of rg4 aluminum. i don't own an noe brass mold so this will be the first.

skimmerhead

[johnny356ER]

Swede,

Sorry, but can you remove me from the list on this buy?
I hate to back out, but I'm still not back to work...
Thanks,
johnny

[SwedeNelson]

Will close this buy Saturday.
Start to get out a PM for payment today.

H.Callahan
What would you like to order? and I will get it on the list
and a PM out for payment

Thanks to all that have ordered.
Al Nelson

[H.Callahan]

Swede,

I am already on the the list for a brass mold (Post #3, 2nd person on the list). We are doing the brass inspite of not getting 15 orders?

[Love Life]

Payment sent! Now the anticipation grows greater!

[ddixie884]

The check is in the mail.......................

[skimmerhead]

Hi Al, i'm #14 on the brass mold list and you have me down for a pb mold, i posted a gc mold. please make mine a solid 4 cav gas check. thanks

skimmerhead

[H.Callahan]

PO Money Order incoming.

I can't stand the anticipation!

[PbHurler]

Al,
Check's going out tomorrow (May 4, 2012) Thank you

[Shedhunter]

Payment Sent! Thanks!!!

[GRS1]

Payment sent Swede! Thank you

[Dschuttig]

If it's not to late, can you put me down for an RG4 PB? Thanks, Dan

[ColColt]

Late comer myself. If any are left over or if it's possible to still get in, I'd like the PB 3 cavity aluminum, no HP.

[trmungle]

Payment sent today. Thanks, Tom

[HighHook]

I would like one RG4 GC please.

[SwedeNelson]

OK - Had computer problems so didn't close buy until today.
This buy is closed.
Will update list with orders and get payed orders on the list.

Thanks
Swede Nelson

[skimmerhead]

about how long before these are ready to begin shipping ? thanks

skimmerhead:lovebooli

[SwedeNelson]

skimmerhead

This one has two before it.
Mould blocks are ordered and about done.
Sprue plates are about done.
Hardware is on hand.

You can check our schedule here:
http://castboolits.gunloads.com/showthread.php?t=142415

Thanks
Swede Nelson

[skimmerhead]

skimmerhead

This one has two before it.
Mould blocks are ordered and about done.
Sprue plates are about done.
Hardware is on hand.

You can check our schedule here:
http://castboolits.gunloads.com/showthread.php?t=142415

Thanks
Swede Nelson
sounds good, thanks

skimmerhead

[H.Callahan]

Yeah, it's kinda like waiting for Santa Claus to arrive, isn't it?! :kidding:

Since we have a little time on our hands...

This will be my first brass mold. Is there any particular break-in procedure or special tricks that I should use? I have mostly used iron before. I tried aluminum and had such poor luck with them that I won't buy them again unless there is absolutely no other alternative.

So, what should I know about brass?

[shawnsmc]

paypal sent today

Thanks,
shawn

[H.Callahan]

Hey Swede!

I noticed on your latest update to the schedule that this GB had dropped off. Does that mean (be still, my heart!) that these are done (or close) and I should pitch a tent by my mailbox?

[SwedeNelson]

H.Callahan

This buy is next on the mill.
Have a small run started that needs to be done first.

Swede Nelson

[H.Callahan]

Ok, I'll hold off driving in the tent stakes for the moment, then!

Thanks for the update.

[slide]

I was just checking the schedule and the aluminum mold was supposed to be shipped yesterday! Hope we are still on track.

[9.3X62AL]

I've been looking forward to this buy's completion. It has been a much-used design for me, and will be my first NOE mould. Just like Christmas as a kid, for sure! :)

[SwedeNelson]

slide

Just finishing up a buy and
this one is next on the mill.

Swede Nelson

[slide]

Outstanding!!!!!

[H.Callahan]

The fact this thread has been moved to the Closed/Waiting for Delivery/Shipment forum is a VERY good sign, I'd say!

(This is WORST than Christmas!)

[smilie=w:

[SwedeNelson]

Just Proofed the form tool and its on the mill.
http://i69.photobucket.com/albums/i80/swedenelson/358477150GrSWCF640x480.jpg

Thanks
Swede Nelson

[H.Callahan]

*drool*.....

[sffar]

Looks super! Been looking forward to getting this mould.
Sam

[Shedhunter]

Look great, can't wait to get this mold.

[Love Life]

I can't wait.

[slide]

Wow, those are sure pretty!!!!

[slide]

I was reading Glen Frywell's "From ingot to target". He said that for the 38 special this was his favorite plinking bullet, very accurate in a variety of guns. Check it out.

[SwedeNelson]

Picked up moulds today, cast with them this afternoon.
Dimensions right on. Weight with my WW material 150.9Gr.
HP 143.6Gr. GC a easy snap fit.
http://i69.photobucket.com/albums/i80/swedenelson/358477150GrSWCF640x480-1.jpg
Lead pot temp. 698F
Mould block temp 396F

Will finish QC and box them up

Shop is still running the brass moulds.
Have to make enough changes that you
cant just run them, have to treat them like
another buy.

Another kick-ya in the but slow down.

Thanks to all that ordered
Swede Nelson

[nicholst55]

Looking good, Al! I'm anxious to see mine - it should work quite well with my S&W M640.

[PbHurler]

These photos have the Carly Simon song "Anticipation" going on in my head.
Thanks for posting them Al.

[slide]

Amen to that Brother!

[H.Callahan]

Shop is still running the brass moulds.
Have to make enough changes that you
cant just run them, have to treat them like
another buy.

Another kick-ya in the but slow down.
As one that was instrumental in pushing for the brass option on this, sorry about that. What makes the setup for brass vs aluminum so different?

[SwedeNelson]

H.Callahan

It uses a different form tool.
So all the offsets are different.
Feeds and speed are different.
The basic set up is the same (as on all buys)
it just needs to be proofed and every thing reset.

I think a better question is what is the same.

Not a problem
They are coming along.
Swede Nelson

[9.3X62AL]

Thanks for keeping us in the loop, Al. Those boolits look MAHVELOUS!

[H.Callahan]

H.Callahan

It uses a different form tool.
So all the offsets are different.
Feeds and speed are different.
The basic set up is the same (as on all buys)
it just needs to be proofed and every thing reset.

I think a better question is what is the same.

Not a problem
They are coming along.
Swede Nelson

Thanks for the explanation. I wouldn't have guessed it was that different. ...and I'll remember that before I stick my nose in again! :oops:

[Love Life]

I got a shiiping notice from NOE today! Neener neener neener!

Time to set up an observation post at the mailbox.

[slide]

Got one too! Looks like the wait is just about over.

[slide]

I just checked track and confirm. My mold is in the post office. It is 0752 here. They open at 0900.

[slide]

I got the mold picked up. This is my first aluminum mold. Very impressed with the workmanship. Putting it through the seasoning procedure. Going to do it four times. Anybody else got theirs yet?

[Love Life]

Mine should be here either today or tomorrow. I can't wait. The last NOE mould I got was the bee's knees!

[Hardcast416taylor]

DANG!!! Now you guys have got me hopping from one foot to the other in anticipation!! The last time I did this routine while waiting for a GB mould from Swede I kept falling over!!:bigsmyl2:Robert

[slide]

Did you get a u.s.p.s. shipping notice by e-mail? The mold shouldn't be far behind.

[Love Life]

Mine is at the post office and will be delivered today!!!! [smilie=w:[smilie=p::guntootsmiley::happy dance:

[CBH]

Got mine today. Typically beautiful workmanship. I'm sure it will cast great boolits. Thanks, Swede!

[nicholst55]

Got mine yesterday. Typically beautiful workmanship. I'm sure it will cast great boolits. Thanks, Swede!

+1, with the minor alteration that it arrived yesterday. It'll be a while before I get to try mine out, but I'm confident that it'll work just as well as my other NOE molds!

[UnderDawgAl]

Got my mould today, and it looks great. I did not get a shipping notice in advance, so don't be alarmed if you don't get a notice.

[sffar]

Got mine, too. Looks great!
No shipping notice received, so a nice surprise.
Sam

[SwedeNelson]

Still getting the hang of the new Click-n-ship
postage from the USPS. Some times trying to get a batch
order to send out a shipping notice doesn't seem to work.
Or I over look something.

Swede Nelson

[H.Callahan]

Swede, are the brass molds on the machine now?

[9.3X62AL]

Al--

The mould arrived yesterday in good order, and is BEAUTIFUL WORK. Many thanks, sir!

[SwedeNelson]

H.Callahan / others

Picked up brass moulds late yesterday.
Cast with them this morning.
Every thing checked out OK.
Will get them boxed up and on the way.

Again thanks to all that ordered.
Swede Nelson

[sffar]

Again thanks to all that ordered.
Swede Nelson

And thank you, Swede! It's always a pleasure doing business with you.
Sam

[Love Life]

I need to take some pictures, but these moulds cast sweet! I made it rain 358477 solids cast of ACWW, and made a 15 pounds of hollowpoints cast from 20:1 lead:tin. Life is good.

[shawnsmc]

I have not got a click to ship email yet and looked at the first post and see I am marked as not paid. I sent payment via Paypal on June 1st for a 5 cavity aluminum mold. Any info would be very appreciated,

Shawn

[slide]

Send a pm to Al if you haven't done so .

[SwedeNelson]

shawnsmc

Its on its way!

Thanks
Swede Nelson

[Hardcast416taylor]

The way I shook hands with Alvin, my mail carrier, you would have thought I was working a pump handle on a dry well! Thanks Swede for a sweet mold.Robert

[trmungle]

Recieved my mold today.Very nice. Thank you, Tom

[Kirk Miller]

Al. great job. Another perfect mold. Looks good and casts even better.
Thanks again
Kirk

[slide]

Yesterday I casted around 200 each of the soilds and the hollowpoints. Followed Al's instructions that came with the mold and had no problems. Today they will get sized and lubed,then loaded.The one thing I appreciated was the difference in the weight. This is my first aluminum mold.

[skimmerhead]

Hello Al, i got my aluminum mold at the begining of the week and i have to say i was impressed! buttttt i got my brass mold in today and i was flabergasterated,WOW, thats is nice, better than expected! thanks a bunch.

skimmerhead[smilie=w::bigsmyl2:

[PbHurler]

Hey Skimmerhead,
Wait untill you cast with your brass mould; you're gonna love it! I managed to drop about 450 saturday morning before the oppressive heat set in, as cast weights averaged 150.4 gr. (plain base mould) and .360" dia's with my alloy.
It looks like my 2-banger Lyman mould will be getting it's retirement papers.

Thanks again Swede for running this mould, and in brass. Another fine mould!

[HiVelocity]

Check this out:

http://castboolits.gunloads.com/showthread.php?t=158681

HV

[H.Callahan]

My brass mold showed up this morning. All I can say is ... WOW!!. Damn thing looks so good, I almost don't want to cast with it. It seriously looks like something that should be in a glass display case for viewing -- and with infrared beams guarding it. It is, seriously, the best looking mold I've ever seen. The cavities appear to be perfect. I can not wait to try it out (but am going to have to, until at least the weekend).

Thanks Swede, for a wonderful job. It was worth every penny and I haven't even cast with it yet! (BTW Swede, the thermometer arrived along with the mold. Thanks again!

BTW, as this is my first brass mold, do the instructions supplied apply to it as well? I want to get it broken in correctly and keep it in good shape!

[357 Voodoo]

Got my brass and my aluminum moulds today Exelent as all ways Thanks Al for the fine work

H.Callahan What i do with my brass moulds is a Good scrubbing with dish soap than one heat cycle and one last scrubbing assemble and cast away.