Attention! Attention! Rerun Miha .45-200g Cramer 4 cavity mold

[Triggerhappy]

Back by popular demand! Original thread below:
http://castboolits.gunloads.com/showthread.php?t=97566

Ordering directions, and how the process works.

To make sure everyone's on the same page, below is an outline of how this group buy will work.

This mold will be a brass .45 200 grain 4 cavity mold using an identical cherry used in his last .45 200g run which was very popular. This mold has the base similar to the H&G68 and a Miha designed ogive which is very popular with 1911 shooters. I personally like using this bullet in my XD's because it simply feeds without any problems. This is the same bullet design Miha started out with here in his single cavity, then his 2 cavity Cramer molds.

The mold will be available in two sizes, .452" OR .454". You will also have the choice of a solid bullet mold OR a Cramer style hollow point mold. The hollow point mold can also create solid bullets by turning the HP pins around.

The Hollow point mold will come with round cavity pins. 5 sided cavity HP pins are available for an additional cost. (Most people opt for the extra pins) Cavity size and Solid/HP can not be mixed within a mold. You're getting either a HP or Solid mold in one size per mold. The molds will be offered in either .452" or .454" and should weigh around 200g in HP and slightly more in solid. Standard Lee 6 cavity handles will work with this mold. (Miha also has some higher quality handles available on his site)


1. Choose which size mold(s) you want. The options are either .452" or .454"

2. Choose whether you want a Hollow Point or Solid bullet style. Prices and shipping are below.

"SOLID" = NO Pins - $95 + $15 freight = $110.00 total
"Hollowpoint" - $130 + $20 freight = $150.00
Hollowpoint mold with set of 5 sided pins as well, +$16 extra for a total of $166.00
If you purchase 2 molds Miha will ship both for $25.00

3. Post on this forum thread your mold choice stating HP or SOLID and size, and your contact email address. Please "code" your email address so it can't be gleaned from the site by bots. Example below.
"triggerhappy at domain dot com"

4. I will add you to the list in post #1 and keep a running total just for giggles.

5. When Miha is within a couple of weeks of shipping I will close this thread. Do not get left out, once it's closed the raw materials will be ordered by Miha and we will not be able to slip you in. MAKE SURE YOU OCCASIONALLY KEEP AN EYE ON THIS THREAD.

6. Miha will use the list in post #1 of this thread as his orders list. Please make sure it's correct and what you want. Once the molds are completed, boxed and and ready to ship Miha will email you using the email addresses on this post to send you a payment request through Paypal.

(Do not gripe about Paypal here. I agree it's lousy and has it's problems, but it's what usually works. Remember Miha is in Slovenia.) Pay via Paypal or another agreed upon method between you and Miha. The Paypal requests go out in batches, so be patient, you'll get yours. The system can only handle so many at one time.

7. When this group buy closes depends on how many people get signed up. The more interest the sooner these will get built.

8. Once your mold has been funded Miha will ship it. Delivery within the US usually takes a couple of weeks. Sometimes a little more, sometimes less.

That about sums it up. If you have any questions please post on this thread or send me a PM.

If you have ordering information please only post it on this thread. Do not send me ordering information in a PM. I prefer to keep the record on this thread so there are no questions.

Thanks!

TH

------------------------------------------------------------------
I'll start it off...

brian at macgurus dot com - (triggerhappy) .452" HP All pins
medicq at comcast dot net - (MedicDQ) Need your size preference
mirelandv at gmail dot com - (mebe007) .452" HP All pins
g(underscore)blomquist(at)msn(dot)com - (2hawk) .452" HP All pins
devilsace at hotmail dot com - (Thinktwicez71) .454" HP All pins
lpeden at frontiernet dot net - (1911GrayWolf) .452" All pins
krantzent at googlemail dot com - (Snoopz) .452" HP All pins
icecold at izoom dot net - (icecold) .452" HP All pins
imprezions at yahoo dot com - (TravelingMan0491) .454" HP All pins
dragonrider at charter dot net - (dragonrider) .454" HP (ROUND PINS ONLY)
auzzie101 at msn dot com - (auzzie101) .452" HP All pins
huntnman at swbell dot net - (huntnman) .452" HP All pins
pattardi (AT) comcast (DUH) net - (phillip) .454" HP All pins
gocaptainawesome at hotmail dot com - (captain_awesome) .452" HP All pins
gwdisney02 at newwavecomm dot net - (firewalked1) .454" HP All pins
Bodydoc447 at aol dot com - (Bodydoc447) .452" HP All pins
jcgraeler at gmail dot com - (double00) .452" HP All pins
stfagen at msn dot com - (MightyThor) .454" HP All pins
danielklamfoth at gmail dot com - (denielk) .452" HP All pins
agrijag42 at mac dot com - (MikeS) .452" HP All pins
tcbnick at sbcglobal dot net - (tcbnick) .452" HP All pins
jamesallen1954atyahoodotcom - (jmcghee) .452" HP All pins
nathancampbell79 at gmail dot com - (tayous1) .452" HP All pins
kjhowler AT gmail DOT com - (Chapped Lips) .454" HP (ROUND PINS ONLY)
1DBBEHR AT COX DOT NET - (1dbbehr) .452" HP All pins
Junghc at sbcglobal dot net - (powderburner) .452" HP All pins
kevin dot ord at frontier dot com - (lostinthetrees) .454" HP All pins
ericl1 at charter dot net - (ltdshooter) .452" HP Round HP pins ONLY
fivegunner at sbcglobal.net - (fivegunner) .452" HP All pins
brucemartin13 at yahoo dot com - (chiefappraiser) .452" HP All pins
Kschuma1 at san.rr.com - (Baja_Traveler) .452" HP All pins
Diamondean at hotmail dot com - (DiamondD) .452" HP All pins
sthwld64 at gmail dot com - (castblast) .452" HP All Pins
69roadrunnerboz at comcast dot net - (edler7) .454" HP All pins
mpbarry1 at gmail dot com - (mpbarry1) .452" HP All pins
anthonybennett at comcast dot net - (AnthonyB) .452" HP All pins
mlkeith45 at aol dot com - (mtmark45) .452 HP All pins
mlaustin(at)ucdavis(dot)edu - (mlaustin) .454" HP All pins
rwhyte at wi dot rr dot com - (midnight) .452" HP All pins
kfreeouf at neb dot rr dot com - (freeokw) .452" HP All pins
sugdenjw AT msn DOT com - (Iron Mike Golf) .452" HP All Pins
imb123 at bellsouth dot net - (Fire_Stick) .452" HP All pins
E @ edsanford at cox dot net - (Echo) .454" HP All pins
Colt_SAA at RocketMail.Com - (colt_saa) .452" HP All pins
wahnehega at usa.com - (Spartacus) .452" HP All pins
wahnehega at usa.com - (Spartacus) .452" HP All pins - customer wants two molds
debent55 at frontier dot com - (Don1955) .452" HP All pins
tfehlhab at swbell dot net - (TFF) .452" HP All pins
tfehlhab at swbell dot net - (TFF) .454" HP All pins - customer wants two sizes
jeremy dot brewster at gmail dot com - (buyobuyo) .454" HP All pins
rsh at att dot net - (zipdog) .452" HP All pins
jjjordan at bellsouth dot net - (jjjds230) .452" HP All pins
FLYERTRYER at AOL dot COM - (45-70 shooter) .452" HP All pins
frosstyx_at _gmail_dot_com - (Noxi0uS) .452" HP All pins
engine4on at gmail dot com - (engine4on) .452" HP All pins
gary.banas at gmail.com - (gary0529) .452" HP All pins
e kellams 8 at g mail dot com - (Edward429452) .452" HP All pins
gunsmoke4570 at aol dot com - (Gunsmoke4570) .452" HP All pins
dshankin at gmail dot com - (d0n) .454" HP All pins
Caleb. Branscome at gmail. Com - (DrB) .452" HP All pins
willsfxsts at msn dot com - (hotwheelz) .452" HP All pins
Roger.Ronas0 at gmail dot com - (Roger Ronas) .454" HP All pins
davidaker at hotmail dot com - (davidaker) .454" HP All pins
vickiandbob at frontier dot com - (shotstring) .452" HP All pins
louiestanfield at gmail dot com - (CPL Lou) .452" HP All Pins
liljohnnie69 at gmail dot com (liljohnnie) .454 HP ROUND PINS ONLY
bobkelley1 at comcast dot net - (old wonderer) .452" HP All Pins
5090shiloh at gmail dot com - (Aaron) .454" HP All pins
mtheath at mchsi dot com - (tomme boy) .452" HP All pins
wind28631 at gmail dot com - (johnfl) .452" HP All pins
sidneyjanetsnow at bellsouth dot net - (JoeBob) .454" HP All pins
skeepes at comcast dot net - (Harry Callahan) .452" HP All pins
Stoneaxe42 (At) Yahoo (doot) Com - (Ozarklongshot) .452" HP All pins
codya at potlatch dot com - (cba257) - .452" HP All pins
kbcombrink [at} att {dot] net - (KCcactus) .452" HP All pins
Dirtdgger3355atyahoodotcom.(dirtdgger) - .452" HP All pins
justingrosche at yahoo dot com - (justingrosche) - .452" HP ROUND PINS ONLY
mikael[at]ritzen[dot]st - (Mikael) .454" HP ALL Pins
Duxr2shoot at sbcglobal dot net - (Okie2) .452 HP All pins
frankedwardthompson at gmail dot com - (Fthomp) .452" HP All pins
kentuckycajun at juno dot com - (kentuckycajun) .452" HP All pins
Ebashyagrill at aol dot com - (bxchef29) .452" HP All pins
robertzanoni at yahoo dot com - (dagunnut) .452" HP ALL Pins
Mhooper at amaonline dot com - (castblaster) .452" HP All pins
ydoibuy at verizon dot net - (TractorCrawl) .452" HP All pins
LCEL at hotmail dot com - (LabGuy) .454" HP All pins
mymodel52atcomc.net - (thebigmac) .454" HP All pins
brtram at comcast dot net - (ocelott) .452" HP All pins
alchucks at cableone dot net - (GREYGHOST) .452" HP All pins
Stevecsnare at gmail dot com - (Silver_Silver) .452" HP All pins - Updated email address
chuck doa 2002 at yahoo dot com - (Chuck4570) .454" HP All pins
mkstarling at gmail dot com - (mstarling) .452" HP All pins
crittrcallr at sbcglobal dot net - (Sheriff) .452" HP All pins
LeeCorley at frontier dot com - (Tripod6324) .452" HP All pins
jeff5tg at yahoo dot com - (PB234) .452" HP All pins
bennyritter at yahoo dot com - (slide) .452" HP All pins
wade plummer at gmail dot com - (wl620) .452" HP All pins
pardue10 at comcast dot net - (uaskme) .452" HP All pins

THIS BUY IS NOW CLOSED!

107 molds on order so far... HP BUY CLOSING SATURDAY THE 10TH

Solid mold list moved to post 307.

[Triggerhappy]

Medicdq, I need what kind of mold you want, and a size please. Also, please double check your name as I have medicdq as your handle but your email address is only medicq.

Let me know,

Thanks!

TH

[Triggerhappy]

Please check your handle and email address to make sure I got them moved over correctly.

[Triggerhappy]

Now for some bait.... These photos are the same bullet but in a 2 cavity mold. The mold you're ordering is a 4 cavity model.

http://castboolits.gunloads.com/attachment.php?attachmentid=26636&d=1289171004

http://castboolits.gunloads.com/attachment.php?attachmentid=26637&d=1289171090

[mebe007]

add me in for the additional pins

also to be honest just double checking, the #'s you listed shouldn't it be $166 with both sets of pins?

thanks,
mark

[Triggerhappy]

http://castboolits.gunloads.com/attachment.php?attachmentid=26638&d=1289171148

[cbrick]

Are these ALL four cavity, even the Cramer HP's? Two cavity? I read through your post twice, could have missed it I guess but . . . .

Rick

[Triggerhappy]

mebe007, Done.

[Triggerhappy]

http://castboolits.gunloads.com/attachment.php?attachmentid=26639&d=1289171210

[Triggerhappy]

cbrick, it's in the title, and I just added it in the body so it's a little more clear. Sorry about that, easy to overlook. This is a 4 cavity mold. The pics I posted are from the older 2 cavity version because I don't have pics of the 4 cavity version yet. Should be able to post some soon.

[mebe007]

last question as a double check, is it true that one can flip the pins for a solid rn fp?

[Triggerhappy]

mebe007, As far as I know, nothing has changed in the design of this mold to preclude you from flipping the pins for solids. I'll be able to verify that when I get the new mold from the last order. I'll specifically try it and post come pics. I know it worked on the 2 cavity version and this should be a 4 cavity copy of that.

[mebe007]

last question and i know there can be no exacts given here. but generally in group buys how long does it take for this thread to turn into molds at the door? i apologize for this question i am just new around here.

[Triggerhappy]

mebe007, No worries, happy to try to answer that question. It all depends on how fast we get a group of buyers signed up and how quick we can close this buy as well as what else he's working on.

The last .45-200 mold I opened the group buy thread on November 7th, 2010. We got great response and Miha closed the buy on 1-31-2011 with 112 molds ordered, so he could order the materials. 3-8-2011 Miha posted that we was about to receive the mold blocks. I expect we'll get our bills for the molds this week or next and receive the molds a week or two after that.

It takes time, these are custom molds of the highest quality. Miha also had several other very large orders to get out like the H&G68. It's all relative to the number of people we get signed up and what else is on the machine. Wish I could give you an exact date, but at least this gives you some idea.

TH

[mebe007]

no its all good. basically i was looking at the time frame for hoarding the money in my slush fund. gotta make sure i have my wiggle room. so now i know if i can get that 452460 mold to hold me over with some more casting fun

so it would be a couple months minimum to delivery essentially

[Triggerhappy]

I think it's safe to say a few months to completion. At least.

I'm in the same boat, have to juggle funds when the molds get close to shipping.

[TravelingMan0491]

HELL YEAH! I've been waiting for this to come back around. Put me in for one:

.452 hollow point with all of the pins

imprezions at yahoo dot com

[Triggerhappy]

TraveingMan,

You're on the list, finally! Welcome!

TH

[tonyjones]

TH,

Put me down for a .452" solid. tony dot jones1951 at att dot net. Could you post a photo of the solid nose version?

Thanks and regards,

Tony

[Triggerhappy]

Tony,

I'll post a photo of the solid once I get the first version of the mold, should be soon. I have never cast the solids because I prefer HP's. The solid looks just like the HP, with the front flattened off, it's not pointy.

You're down, welcome.

TH

[Triggerhappy]

Look at the bottom photo and just imagine the pins flipped.

[firewalkerd1]

Can one get the 5 sided pins only instead of the round ones?

[tonyjones]

TH,

I bought the Cramer HP version the last time you ran this buy. I'm expecting delivery in the next few weeks. It sounds like the solid will be a RF profile. It should cast faster than reversing the pins in the Cramer mould.

TJ

[Flintlockrecord]

One 4 cav brass .452 solid please. Delivery to New Zealand

ian at knight dot gen dot nz

[rollmyown]

I can hear wedding bells. A new Ruger 1911 and one of these beauties!.
Now what diameter? I can't slug it cos I don't have it - yet. I'd rather not size excessivley. What do you think?

[Triggerhappy]

firewalkerd1, I can put a note on the list if you want. the round pins are the standard, the 5 sided pins are an extra cost. We'll see what Miha can do. I wouldn't expect it to be a problem. The round pins are nice too, I use mine all the time.

TH

[Triggerhappy]

Tony,

The solid mold will certainly cast faster than the HP version with flipped pins. It's still a nice option to have that ability. Especially for people that can't buy two molds.

I like shooting the HP version because it saves a little lead each time, (almost 10%) and I can push them a little faster which works for what I'm doing.

TH

[Triggerhappy]

Flintlockrecord, You've been added to the list in post #1. Welcome.

I think you'll be the only person in NZ with this mold.... And you'll love it.

TH

[Triggerhappy]

rollmyown, I can't answer that for you. Most of the Miha .45 molds I have are .452" and they work great, especially in 1911's. If you don't want to size a great deal go with the .452", should work great for most alloys.

[Triggerhappy]

Don't wait to get on this list guys. You'll be sorry if you miss it.

[Triggerhappy]

Shamelessly borrowing Miha's latest photos of this mold... And no, yours aren't ready yet, these are from the last run of molds. Yours will look similar.

http://castboolits.gunloads.com/attachment.php?attachmentid=31835&d=1303825254

[Triggerhappy]

http://castboolits.gunloads.com/attachment.php?attachmentid=31837&d=1303825287

[Triggerhappy]

http://castboolits.gunloads.com/attachment.php?attachmentid=31838&d=1303825321

[dragonrider]

OK I'll take a 4 cavity .452 HP, round pins only,
Here is a question, is it possible to get a blank set of pins UNassembled, that is with the guide pins but not screwed together????
Thanks

[Triggerhappy]

http://castboolits.gunloads.com/attachment.php?attachmentid=31839&d=1303825339

[Triggerhappy]

http://castboolits.gunloads.com/attachment.php?attachmentid=31836&d=1303825271

[Triggerhappy]

dragonrider, I'm sure you could work something out with Miha. Please contact him directly for anything outside of the norms of this buy. If we start making it too complicated at this end we'll just have a wreck.

I added you with round pins only. Let Miha know what you want with the spare set of pins.

I need your coded email address for the list, otherwise you won't get notified.

[auzzie101]

I'm in, .452 with all of the pins.

auzzie101 at msn dot com

[Triggerhappy]

auzzie101,

You are now on the list, welcome.

TH

[bpratl]

What would the diameter be of the dropped .452" and the .454" bullets?

[Triggerhappy]

That would be .452" and .454". Of course that depends on what alloy you're using and hot hot you're casting. The target is the actual size of the mold, but there are variables involved. Some people shoot as dropped, most size to true the bullet and provide more size consistency.

TH

[bpratl]

That would be .452" and .454". Of course that depends on what alloy you're using and hot hot you're casting. The target is the actual size of the mold, but there are variables involved. Some people shoot as dropped, most size to true the bullet and provide more size consistency.
TH

I have been using CO WW and sizing to .452" using LEE molds and I noticed that most buyers have ordered the .452" mold. Would I be better to order the .454" if I am going to size to .452"? As you can tell I am new to casting and a little confused.

[Triggerhappy]

No problem. I quite often cast air cooled ww and use a .452" mold, then size to .452" which doesn't take much. Most users will want .452" so that's probably the best place to start.

Unfortunately there's no way i can tell you which size to get.

[mebe007]

I have been using CO WW and sizing to .452" using LEE molds and I noticed that most buyers have ordered the .452" mold. Would I be better to order the .454" if I am going to size to .452"? As you can tell I am new to casting and a little confused.

May try slugging your bore. May set your mind at ease

[icecold]

this is great i cant wait to start casting these..i see im in the list already .452 with all pins.now to start hoarding lead.

thanks
pete

[huntnman]

I'm ready, 1- 452" all the pins.huntnman at swbell dot net. Now if I could get a twin or hp swc only in 44. for my 629!

[Triggerhappy]

huntnman,

You're all signed up. Congratulations!

TH

[Phillip]

Hit me for a .454" HP with all pins.

pattardi (AT) comcast (DUH) net :lol:

[captain awesome]

i am getting into to many of these. hit me up for hp one with all pins. .452

[2hawk]

Thanks for getting this going TH!

[Swede44mag]

Triggerhappy: How long do you think this buy will stay open?
I missed out on the last one didn't know about it untill it was to late.
I just signed back up for another group buy.

I may have to start looking for another 1911 the new Ruger looks interesting.

[firewalkerd1]

This is great news. I'll take a HP .452 with all the pins.

gwdisney02atnewwavecommdotnet (firewalked1)

[Triggerhappy]

Phillip, captain_awesome and firewalkerd1 are added to the list. Welcome.

I need captain_awesome's email address please. Without it we can't send a bill.

Thanks!

TH

[Triggerhappy]

Swede,

There's no way to know at this point how long this buy will stay open. In all honesty I would guess a couple of months. It depends on how many people sign up and what Miha is working on. If he gets slow this may move faster. The faster we get people signed up the faster producing the mold will be.

Wish I had a set date for you, but it doesn't work that way with these custom molds.

TH

[Bodydoc447]

Triggerhappy,

I guess I better get in while the getting is good. I'd like a .452 with all the pins.

Thanks,

BodyDoc447

(Bodydoc447 at aol dot com)

[Triggerhappy]

Bodydoc447, you're good to go. Should be a good one.

TH

[Triggerhappy]

dragonrider & captain_awesome - I need your email addresses for the order please

[captain awesome]

sorry, here it is

gocaptainawesome at hotmail dot com

[Triggerhappy]

ca, thanks, that's what I needed.

[double00]

I will take a hp with all the pins. jcgraeler at gmail dot com

[double00]

that would be in .452

[Triggerhappy]

double00, I'll add you but I need to know what size you want.

[Triggerhappy]

done, thanks

[MightyThor]

Not trying to be greedy, but I would like to get a second mold in .454 for my other 45's

stfagen at msn dot com 1 mold (.454" HP) "MightyThor" All the pins please.

I keep looking at your boolits and get drool on my keyboard.

[Triggerhappy]

MightyThor, you're in! Welcome. Not greedy at all.... It's a sickness.

TH

[danielk]

Put me down for a .454 hp with both sets of pins. danielklamfoth at gmail dot com

[Alan]

I just realized I'm in the old thread as aeatwood2 at yahoo dot com. My paypal has to go through aatwood2 at tx dot rr dot com

[Triggerhappy]

danielk, you're good to go. Thanks!

TH

[Triggerhappy]

Alan, I updated your email address on the old thread. You should send Miha a PM at this point so he's aware of it. He very may well come back to this list, or he may use an old copy of it. If he goes by this version you'll be in good shape.

Cheers,

TH

[MikeS]

Put me in for a .452 with all pins

agrijag42 at mac dot com

[tcbnick]

OK I'll jump, Put me in for 1 in .452 with all pins
tcbnick at sbcglobal dot net
Thanks
Nick

[jmcghee]

Put me down for a hollow pt with extra pins.452 thanks Jim jamesallen1954atyahoodotcom

[Triggerhappy]

MikeS, good to go with the .452".

tcbnick, well, there you go ordering another mold.... Really better not tell the wife.... All set with a .452"

jmcghee, you're in for a .452" HP.

Welcome all!

TH

[tayous1]

Put me down for a hollow pt with extra pins.452 thanks nathancampbell79 at gmail dot com

[MikeS]

I just want to make sure I made myself clear, I want a HP mould with both types of pins. These will be made from brass, not aluminum, right?

[Triggerhappy]

tayous1, you're on the list, welcome!

TH

[Triggerhappy]

MikeS, Brass, HP All pins....

Should be good to go.

Cheers,

TH

[Chapped Lips]

TH......sign me up for one in .452 with all pins.

kjhowler AT gmail DOT com

Thanx for being the pointnanny. :)

Getting this in celebration of the demise of the OBL.

[Triggerhappy]

Chapped Lips, great reason to get this mold! You're on the list.

Cheers,

TH

[1dbbehr]

TH, Put me down for .452 HP with the extra pins.

Thanks,
1DBBEHR AT COX DOT NET

[Triggerhappy]

1dbbehr, you're down! Welcome.
TH

[powderburner]

I would like to get on board for a .452 hp with all pins.
Junghc at sbcglobal dot net

[1lostinthetrees]

Include me for .452 hp all pins
kevin dot ord at frontier dot com

[Triggerhappy]

powderburner & 1lostinthetrees,

You're both on the list. Welcome. And a hearty welcome to the site and the addiction. Once you start with Miha molds you don't go back.

TH

[Ltdshooter]

Triggerhappy,
Put me down for one (1) 4 cavity .452 mould with regular (round) HP pins
Eric

ericl1 at charter dot net - (ltdshooter) .452" HP regular round HP pins

[dragonrider]

dragonrider at charter dot net

[ChuckJaxFL]

TH;

I suppose this run of 4-cavs is going to ensure that another run of 2-cavs isn't going to happen soon at all, or am I mistaken?

I know you can't predict the future. Can you speculate with any degree of certainty?

I'd jump in this w/ both feet, but have pretty bad carpal tunnel. A 2-cav is plenty for me.

[Triggerhappy]

Ltdshooter, you're in, and thanks for making it easy.

Dragonrider, thanks for the email address.

ChuckJaxFL, I doubt that we would get many takers for a 2-cav at the moment. I understand the weight issue. Keep a watch out, I'm sure eventually there will be another 2 cav version buy. You might also be able to purchase one from someone buying a 4-cav. Worth a shot.

TH

[fivegunner]

Hi, could you put me in for a 4 cavity .452 HP with the hex pin`s. fivegunner at sbcglobal.net

[Triggerhappy]

fivegunner,

You're in! Welcome to the best buy on the forum.

TH

[blaser.306]

Any chance that I can change my .452 ( to ) a .454 ? I would rather size down than wish I was big enough ! Seems to be the story of my life !!!!!!

[Triggerhappy]

blaser, As far as I know you're not in on this buy. Please correct me if I'm mistaken.

TH

[blaser.306]

Sorry Brian I am in on the original buy ! Didn't see what I was posting on ! At any rate being it is still runing is it possible to do the change from .452 to .454 ?

[Triggerhappy]

blaser, the molds are done and should get billed next week after packaging this weekend. The only possible way to change your order is to contact Miha directly. It's possible he made some extras and you could exchange sizes. Changing the list at this point won't make a difference.

TH

[chiefappraiser]

Is it too late to get in on this. If not I would like to order a 4 cav .452 with all of the pins.

[Baja_Traveler]

I'm all in for a .452 hollow point with all of the pins.

Kschuma1 at san.rr.com

[Triggerhappy]

chiefappraiser, got you added but I need your coded email address please. Without it we can't notify you about your order.
TH

[Triggerhappy]

Baja Traveler, you're good to go. Thanks and welcome.

TH

[DiamondD]

Any chance a guy could still get in this?

If so I would like a 452 hp with all the pins. What a great looking boolit!

Diamondean at hotmail dot com

[castblast]

I'm also all in for a .452 hollow point with all of the pins.

sthwld64 at gmail dot com

[rollmyown]

I'd like a 4 cav solid in 452 if it's not too late.

[edler7]

I'm in for a .454 HP with all pins

edler7 at hotmail dot com

[mpbarry1]

I was gonna get a lee for my first mold, but what the heck. that one is pretty!

4 cavity, .452, all the pins please! I am about ready to cast my first bullets. :)

[Triggerhappy]

DiamnondD, castblast & edler7, you are all added, welcome.

rollmyown & mpbarry1, you're on the list, but I need your coded email addresses. Without the address you will not get notified of the order.

Cheers to all.

TH

[Triggerhappy]

My apologies for not updating this list over the weekend. I was gone doing some Hazmat training.

TH

[mpbarry1]

mpbarry1 at gmail dot com. Thanks!

[Triggerhappy]

mpbarry1, Thank you, it's been updated.

[AnthonyB]

Please add me in for another .452 mould with all pins. E-mail is anthonybennett at comcast dot net; no spaces.
Tony

[rollmyown]

bert000 at yahoo dot com

Thanks TH!

[Triggerhappy]

AnthonyB, you're good to go.

rollmyown, thanks!, Got it.

[MtMark45]

mlkeith45 at aol dot com (mtmark45) .452 all pins

[Triggerhappy]

MtMark45, you're added & good to go. Welcome to the buy, and welcome to the forum. It's a nice place to hang out.

Cheers,

TH

[eagleotto]

Out of curiosity, has anyone from the last buy tested expansion on these? Might motivate some seeing that.

[mlaustin]

Agh, been trying to avoid it long enough....

454 with all the pins please. My Miha H&G68 is perfect in my 1911's but has issues in my p220 and xd. Guess I need this one too...between this and the H&G503 i'm going to be going bankrupt!

[birdadly]

So I have something to do this coming fall/winter... I'll bite on this as my first-ever mold. Those boolits on page 1 just look too dang nice, especially the 5-sided HP (I'm not sure I've ever seen something like that!).

I'm new, and so worry that I'll buy the wrong thing :) So unless someone tells me this 'definitely' won't work in a 3" 1911 Kimber, then I am in. I haven't slugged my barrel but from reading around, it sounds like I should be safe getting the .452, so will try that.

452 HP with all extra pins
birdadly at yahoo dot com

Now to read on sizing and lubing... ... this site keeps me busy :)

[Triggerhappy]

eagleotto, go look at the last buy for this mold, I posted a bunch of expanded boolits there. They're about halfway through the threads. There's also multiple threads devoted to specifically that, the expansion characteristics of different boolits, alloys etc.

[Triggerhappy]

mlaustin, need an email to place the order.

You're on the list but without an email you won't get the order.

[Triggerhappy]

birdadly, you're on the list and good to go. Welcome.

This bullet will work great in your 3" Kimber, I use it in a 3" Para Ordinance Carry12 for concealed carry. Very accurate and expands great if you use soft alloys. The penta pin is kinda nice, makes them look kinda cool. I think either type of cavity expands well.

[eagleotto]

Put me down for one HP in .452 with all the pins please.
Email: eagleottofh at yahoo dot com

[buyobuyo]

Another quick will it feed question.

I just picked up my first 1911 (a Rock Island Armory) this weekend, which is my only .45. I have a couple of 2-cav Mihec molds already, so I was instantly interested in this one when I saw this GB. However, the manual for my gun states that the barrel ramp is cut to feed RN ammo. I'm wondering if anyone has tried these in a RIA before, and if there are any feeding issues?

Also, is it known yet when this buy will be closing?

Thanks.

[Triggerhappy]

These are about as round as it gets. Should work fine. What the manual is saying is the 1911 is designed to function with hardball, which has a round nose profile.

No one knows when the buy will close.

[Triggerhappy]

eagleotto, need email info for the order....

[Triggerhappy]

if you want to place an order here, please go read post #1.

[eagleotto]

Email info added, sorry trigger.

[buyobuyo]

Trigger, thanks for the information.

Hopefully the wind will behave so I can get to the range this weekend to see how it runs. I'll try some HP ammo if Wally World has any.

Once I can get the barrel slugged I'll put in my order so I know I'm ordering the right size, although 452 will probably be it.

[Triggerhappy]

eagleotto, got the info and have added it to post 1. Thanks.

buyobuyo, sounds great. You'll like it. These will feed a little better than commercial jacketed HP's.

TH

[mlaustin]

forgot the email - mlaustin(at)ucdavis(dot)edu Just so you don't have to scroll back up, I wanted a .454 with all the goodies.

Thanks!

[Triggerhappy]

mlaustin, Most excellent, thank you sir. It's been added.

Cheers,

TH

[rintinglen]

sign me up for an hp mold with just the round pins. ghoglin-at-hotmaildotcom

[Triggerhappy]

rintinglen, need to know what size mold you want.

Thanks,

TH

[midnight]

Put me down for a 0.452 with all the pins!

rwhyte at wi dot rr dot com

Bob

[Triggerhappy]

midnight, you're good to go. Welcome.


TH

[freeokw]

kfreeouf at neb dot rr dot com (1) one 4 cavity mold (452 HP) with both sets of pins, freeokw

(I hope I did this correctly)
Thanks and Semper Fi,
Keith

[Triggerhappy]

Keith,

You're on the list and good to go. Welcome. And Thank You for being a Marine.

Brian

[freeokw]

Thank you Brian! When would you like payment, and in what method?

[Triggerhappy]

freeokw,

Please go read post #1, should explain everything. If you have any questions after reading that I'm happy to answer them.

TH

[Iron Mike Golf]

TH,
Put me down for one of these in .452, with all pins.

sugdenjw AT msn DOT com

[Triggerhappy]

Mauser Rat & Iron Mike Golf,

You're both on the list, welcome! I'll bet this one picks up a little now that the last one is in shipping phase.

TH

[mcyrier]

put me down for one (1) .454, solid, 4 banger brass mold.
thanks.

cyrier at charter dot net

[Fire_stick]

I only have one MiHec mold, and I am relatively new to casting, but it is the best mold I have ever used. Drops bullets of very consistent weight.

Put me down for one mold. HP with all pin options. .452"

imb123 at bellsouth dot net

Thanks TH and MiHec

[Triggerhappy]

mcyrier & Fire_stick, you're both good to go. Welcome....

TH

[Echo]

TH, put me on the list for a .454 w/addl penta-star pins. I understand $165 - right? E @ edsanford at cox dot net.

[Triggerhappy]

Echo, you're on the list for a .454 will all pins for $166.00.

This one is going quick, might not last long.

TH

[Mauser Rat]

Brian (TH),

Thanks for a well organized and extremely efficient GB. I speak for myself, and I am sure many others, in saying that you can part a man from his money more painlessly than almost anyone else that does not have long blonde hair. Seriously though, from the page one post to this point has been the clearest and cleanest GB that I have been in. Would that the whole world was as well run.

Congratulations and if you're ever in this neck of the woods, I'll buy you a cold one.

Thanks to Miha as well. I have two of his moulds already and they are both a work of art and a joy to cast with. If anybody is still unclear on what a service he provides, try to imagine if he had never wandered in here and perfected those great Cramer moulds and agreed to sell them to all of us liquid Pb addicts. Same offer Miha. If you ever take a wrong turn on the way to the shop and end up in Alaska, stop by and let me shake your hand and buy you one Slovenian style!

Kevin :2 drunk buddies:

[Triggerhappy]

Mauser Rat, That's the nicest thing anyone has said to me on this forum. Goes both ways, you ever make it down around here I'll buy you a cold one, or three.

Cheers,

Brian

[colt_saa]

Please include me in this one.

.452 HP

Colt_SAA
at
RocketMail.Com

[Triggerhappy]

Colt, you're good to go, welcome!

TH

[Spartacus]

OK TH, I'll bite. Put me down for 2 of the .452's with all pins.

wahnehega at usa.com

[imsoooted]

i'm afraid to miss out on this one.... i'll take (1) .452 with all pins. thx
john-kirby at comcast dot net

[Don1955]

Put me down for one in 452 w/ HP Pins
debent55 at frontier dot com
thx

[Triggerhappy]

Spartacus, imsoooted & Don1955, you've all been added and you're good to go. Welcome all.

TH

[gcf]

Back by popular demand!

That about sums it up. If you have any questions please post on this thread or send me a PM.

TH



W/ a .452" mold, is it reasonable to expect bullets will drop right at .452" (wheel weights or #2 alloy), or should we expect .452"+?

Thanks!

[TFF]

Please add me to the list! (I tried back in Feb, but was too late - glad the group buy was opened up again)...

TWO sets, one each:

.452" HP All pins
.454" HP All pins

tfehlhab at swbell dot net - (TFF)

Thanks.

[danielk]

trigger, could you change mine from .454 to .452

[Triggerhappy]

gcf, the molds are normalized to drop right at .452", but there are a LOT of variables, the two main ones being mold / lead temp & alloy used. It depends on what you're doing. All molds are the same, if you cast hot the bullets will be a different size than if you cast cooler and slower. Same goes for the alloy, some alloys shrink more than others. For most casters the mold will drop very close to .452", may not be exact for you, depending on what and how you cast.

If you're worried about it being too small get the larger .454" mold. I use the .452" and size it to .452 and it works great for me.

TH

[Triggerhappy]

TFF, you're down for 2 molds, welcome! Sorry you were too late for the last buy on this mold.

danielk, size changed.

TH

[gcf]

gcf, the molds are normalized to drop right at .452", but there are a LOT of variables, the two main ones being mold / lead temp & alloy used. It depends on what you're doing. All molds are the same, if you cast hot the bullets will be a different size than if you cast cooler and slower. Same goes for the alloy, some alloys shrink more than others. For most casters the mold will drop very close to .452", may not be exact for you, depending on what and how you cast.

If you're worried about it being too small get the larger .454" mold. I use the .452" and size it to .452 and it works great for me.

TH

OK, thanks - better to be over then under!

Please put me down for (1) .454" HP mold - w/ all the pins.

gcfron at swbell dot net


Guess I'll be needing a production pot, & some alloy - on a budget... Anyone have any suggestions?

[Triggerhappy]

gcf, you're on the list and good to go.

As for a pot on a budget, look for a Lee pot and a dipper. It's not the best solution for this type of mold but it would get you casting for the least $$. Also start hitting your local tire shops for wheel weights.

If you can afford a little more money look at the Lyman bottom pour pots, they work pretty good with this type of mold.

TH

[buyobuyo]

TH:

Please put me down for a .454 HP mold with all the pins. jeremy<dot>brewster<at>gmail<dot>com

Thanks, Jeremy

[Triggerhappy]

buyobuyo, you're now on the list, welcome.

TH

[zipdog]

I've been trying to talk myself out of this for 2 days, but I can't stand it.
Put me down for a 0.452 with all the pins. That thing is pretty enough to just sit on the mantle as a display piece!

rsh at att dot net

[Triggerhappy]

zipdog, your mantle ornament is on order. Make sure you get some brass polish....

Cheers,

TH

[JJJDS230]

I would like one, .452 with all of the pins.
jjjordan at bellsouth dot net

[Triggerhappy]

jjjds230, you're good to go. welcome to the buy and the forum.

TH

[Echo]

Yo, TH;

I don't see my name on the list - I thought I E'd for all pins.

[Triggerhappy]

Echo,

You're on the list, look again, about a dozen up from the bottom.

Cheers,

TH

[MikeS]

Are getting a set of handles along with the mould an option with this buy? I'm in on the rerun of the #68 and getting a set of handles with those, thought if I could get another set of handles so both moulds are happy that would be a good thing.

[MikeS]

gcf, the molds are normalized to drop right at .452"

I thought Miha said that his moulds will cast slightly over the listed size so the boolits can be sized down to to the stated size easily? I would take that to mean the mould will drop at .453 for the .452 version and .455 for the .454 version. Am I wrong?

[45-70 shoooter]

I'll take a .452 with both pins
FLYERTRYER at AOL dot COM

[firewalkerd1]

Triggerhappy,
Is this offered in PB and BB?

[buyobuyo]

Plain Base only. Read the 1st post for what your options are.

[firewalkerd1]

buyobuyo, I did read the 1st post of options which stated it had a base similar to the HG#68 which Miha is offering in PB and BB. I wanted to know if this was an option. I did not mean to offend anyone by asking a question about something I was not clear about.

[Noxi0uS]

Put me down for a .452 HP w/all pins frosstyx_at _gmail_dot_com

[engine4on]

I would like one, .452 HP with all of the pins.
engine4on at gmail dot com

[Triggerhappy]

My apologies, I've been away for a couple of days doing some Search & Rescue training.

MikeS, Yes you can get handles if you want. I believe they're $23 plus $7 shipping. If you want handles I can put you down for them, but you can also order them direct anytime from Miha's site. Shipping can't be combined. I don't own any of his handles, yet, but I understand they're really nice and much stronger than the Lee handles.

As for size, it all depends on alloy and temp. They should cast slightly oversize allowing you to size and lube easily, but the oversize is hard to say since everyone uses a different alloy and different casting techniques. If you're worried about the mold cavity not being large enough, perhaps go with the larger size.

TH

[Triggerhappy]

45-70, you're good to go, welcome.

TH

[Triggerhappy]

firewalkerd1, Hey, no offense I'm sure. I think he was just making sure you knew where to find that info. My apologies if I didn't make it very clear. This mold uses the Plain Base similar to the H&G68. It's very popular and works well. I think this is by far the most popular mold ever sold through the group buy.

TH

[Triggerhappy]

Noxi0uS & engine4on you're goth good to go. Welcome!

TH

[yancey]

Ok, Ok, I have held out as long as i could. I would like a 452 hp with all the pins
yanceysguns at comcast dot net

[Triggerhappy]

yancey, you're good to go, welcome.

TH

[gary0529]

put me in for 1
.452 HP all pins

gary0529

gary.banas at gmail.com

[Triggerhappy]

gary0529, you're on the list and good to go.

Welcome,

TH

[Triggerhappy]

rintinglen, What size mold do you want?

[Edward429451]

I'm in!

.452 HP plus all extra pins.

How close are we to closing this? It's been awhile since I've done a GB over here, please email me and reiterate payment instructions for a man with no paypal. Thanks!

e kellams 8 at g mail dot com

[Triggerhappy]

Edward, You're on the list, welcome. Please read post #1 about payment other than Paypal. You will have to work that out with Miha directly.

TH

[Edward429451]

Do you have Miha's contact info?

[Triggerhappy]

Edward, Left click on his name on any of his posts and choose either PM or email.

TH

[Gunsmoke4570]

Triggerhappy,

Put me down for a .452" hollow point mold with both sets of pins.

Thanks for being a honcho!

gunsmoke4570 at aol dot com

[d0n]

Hello,

I've been a lurker here for a long time, but I registered just now with hopes of getting in on this group buy (this is my first post). If I can get in on this group buy, I would like the .452 hollow point, also with both sets of pins.

dshankin at gmail dot com

-Don

[Triggerhappy]

Gunsmoke & d0n, you're both on the list, Welcome aboard!

Check out post #1 if you have any questions about how it works.

d0n, welcome to the forum!

TH

[DrB]

.452, with all the pins, please.

Caleb. Branscome at gmail. Com

[hotwheelz]

.452 hollow point with all the pins

willsfxsts at msn dot com

[Roger Ronas]

New to the site but would like in on the GB.

.452 hollow point with all the pins.

Roger.Ronas at gmail dot com

Thanks and cool site.
Rog

[davidaker]

Please add me in as well for .454 HP with both sets of pins.

davidaker at hotmail dot com

Many thanks,

[Roger Ronas]

Need to get a set of handles as well. Where and how?
Thanks,
Rog

[Triggerhappy]

DrB, hotwheelz, Roger & davidaker you're all good to go. Sorry it took me so long to get you on the list, I was away at a 3-gun match all weekend. Shot this bullet in a tactical .45.

Roger, you have a couple of options for handles. You can order them direct from Miha's site online. Or I can add you on this list for a set of handles too, Miha will just bill you for them when he bills for the mold, or you can get ahold of a set of Lee 6 cavity handles which work great with these molds. The Miha handles are far superior and will last you longer. Let me know if you want handles added to your order.

Welcome to the site guys!

TH

[Roger Ronas]

Thanks TH,
If you can add the handles to my order that would be great. Can't use handles till I get the mold anyway. LOL
Thanks again,
Roger

[Triggerhappy]

Roger, got you down for 1 pair of handles. Miha should invoice you when he's ready with the molds.

TH

[Roger Ronas]

Hello TH,
I have a question as far as size to order.
I've never cast, but know that I want to run boolits thru sizing die. Want a finished dia of .452. So do I want to order the .452 or should I change to the .454 so the resizer die will shave some off the boolit?

Sorry for being such a pain on this.
Thanks for everything,
Roger

[shotstring]

TH,

Put me down for a .452 HP with all pins. vickiandbob at frontier dot com

thanks so very much - (glad to finally get in on one of these)

Shotstring (Bob)

[MightyThor]

I posted this in the closed buy thread, but thought I would put it here too. I have been casting and shooting the boolits from my 452 mold and thought I would show a recovered slug. The 452 mold casts at exactly that with my wheel weights I have been running them through my lee sizer just to get the lube set right, but there are very few that show any sign of having been through the the sizer. This recovered boolit was about 6 inches into the soft, wet dirt behind my target. Round nose bullets from the same spot showed very little evidence of having been shot, just bore marks etc. I could probably clean them up and shoot them again, Not so much this hollow point.

http://5rxhxw.bay.livefilestore.com/y1p8muDYsIMOhqbPWb9VbkwHuNmey7Gw5Ctf89mA-o9QcmS71yuYHNxnsxuxo7PRpHiqnpJcBiZD5_lMOuhQ8Qr13zM kKTm9UG0/45.jpg?psid=1

[CPL Lou]

Count me in !

louiestanfield at gmail dot com - (CPL Lou) .454" HP All Pins

Thanks !

[firewalkerd1]

Happy,
Please put me in for a set of handles to go with the mould I all ready have listed.
Thanks Gary

[Triggerhappy]

shotstring & CPL, you're both on the list, welcome!

firewalkerd1, I added a set of handles to your order.

[Triggerhappy]

Roger, For most people the ,452" works great and allows you to size to .452". However, the dropped size of bullets from a mold depend on the alloy used and mold/alloy temp when casting. If you're worried about it go with the larger size and size them down a couple thousandths. There is plenty of lube groove to size them down if you want.

[Triggerhappy]

rintinglen & MedicDQ - Need your size preference please

[Roger Ronas]

Roger, For most people the ,452" works great and allows you to size to .452". However, the dropped size of bullets from a mold depend on the alloy used and mold/alloy temp when casting. If you're worried about it go with the larger size and size them down a couple thousandths. There is plenty of lube groove to size them down if you want.

That's kinda what I was thinking with alloy type and shrinking. I think I'll feel more comfortable getting the .454. If you can change my order to reflect that I would appreciate it.

Still doing a lot of reading, never cast before. LOl

Roger

[CPL Lou]

I need to change the diameter of my mold to .452.
Sorry for any inconvenience.

CPL Lou

PLEASE CHANGE MY MOLD ORDER TO .452

[eagleotto]

Trigger-happy,
I think I would like to make mine .454 as well if that is possible.

[liljohnnie]

I would like to have one.

liljohnnie69 at gmail dot com (liljohnnie) .454 HP ROUND PINS ONLY

[yancey]

This looks like a great GB( but i'm going to have to pull out of this buy)
Please take my name off the list. Thanks, Yancey

[TravelingMan0491]

Triggerhapy,

Could you please modify my order to be a .454 instead of .452. Thank you!

[d0n]

I'm sorry; I'm still learning and reading (I haven't actually cast any boolits yet), and I probably should be going with a .454 + sizer as well. I will be shooting these out of a 1911 and a Ruger Blackhawk. What do you guys think? Sorry again... :oops:

[old wanderer]

Please add me to this list for a 452 size hollow point and handles.

bobkelley1 at comcast dot net

[Triggerhappy]

Roger Ronas, CPL Lou, eagleotto, TravelingMan0491

Your size changes have been noted, please check that I have them right.

[Triggerhappy]

Lil Johnnie & old wonderer have been added, again, please check to make sure I have it right.

Welcome!

TH

[Triggerhappy]

yancey, You have been removes at your request.

Cheers,

TH

[Triggerhappy]

d0n, Is that a request to change yours to the .454" size? I don't want any misunderstandings about what it is you're ordering. If you want to change to the .454" please let me know.

Cheers,

TH

[d0n]

d0n, Is that a request to change yours to the .454" size? I don't want any misunderstandings about what it is you're ordering. If you want to change to the .454" please let me know.

Cheers,

TH

Yeah, I guess I wasn't very clear about that after re-reading my post. I would like to change mine to .454 as well. Sorry about the ambiguity.

[Triggerhappy]

d0n, Happy to make the change, just didn't want to jump the gun if you weren't sure.

Change made.

Cheers,

TH

[TravelingMan0491]

Thanks TH!

[eagleotto]

Mine looks good, thanks again TH!

[birdadly]

...why did I sign up for this whilst knowing that I'm an instant-gratification consumer!!!! Okay, I'll just go fall asleep for a few weeks/months and I'll have one of these in no time! Have a good day everyone!! -Brad

[x101airborne]

After much deliberation, I have come to the conclusion that I will not be able to afford the origional GB 45-200 mold run that I have waited for so long. I would like to offer my mold to the next in line and request being put on the second "re-run" waiting list. I will send what e-mails are necessary to Miha to tell him of the change or Triggerhappy can make the swap himself since he is honcho.

[Triggerhappy]

x101airborne, To be clear, you want to be added to this list? If so what mold do you want?

[x101airborne]

TH, I apologize for any confusion I may have created. Our water heater blew up and ruined sheetrock and such and I was unable to pay Miha for the mold. When I sent the previous message about not affording the mold anymore, I left it up on the screen and my wife saw it. She snuck into my e-mail account and paid for the mold. So please dis-regard previous messages. Thanks. Raymond

[Triggerhappy]

x101airborne, That's a woman to keep. I'll disregard.

Thanks,

Th

[Roger Ronas]

That is a good woman. On a side note, does she have a single sister? You have a keeper.
Roger




TH, I apologize for any confusion I may have created. Our water heater blew up and ruined sheetrock and such and I was unable to pay Miha for the mold. When I sent the previous message about not affording the mold anymore, I left it up on the screen and my wife saw it. She snuck into my e-mail account and paid for the mold. So please dis-regard previous messages. Thanks. Raymond

[Aaron]

.454 Hollowpoint mold with set of 5 sided pins as well, +$16 extra for a total of $166.00

Thanks

Aaron

5090shiloh at gmail dot com

[Triggerhappy]

Aaron, You're good to go, welcome!

TH

[1lostinthetrees]

After some thinking I would like to change my bullet size from 452 to 454.

Thanks!

[tomme boy]

Put me on the list for the .452 with both pins. Thanks. Sent you a PM.

mtheath at mchsi dot com

[johnfl]

Please add me to the list for the .452 mold with both sets of pins. I'd also like a set of his mold handles

Thanks,
John

wind28631 at gmail dot com

[TravelingMan0491]

TH,

Could you put me down for a set of Miha's mould handles as well? Thanks.

[Triggerhappy]

1lostinthetrees, I changed your size to .454"

[Triggerhappy]

tomme boy & johnfl, you're both on the list, welcome!

TH

[Triggerhappy]

TravelingMan0491, handles added.

Cheers,

TH

[Roger Ronas]

Hello Trigger,

Looking over the master list I noticed my addy is incorrect. I checked my post and it's my fault.
The correct addy is:
Roger.Ronas0 at gmail dot com

I forgot the zero in the original post.
I promise to not bother you any more.

Thanks
Roger

[johnfl]

Any idea when these will be made/shipped?

Thanks

[Triggerhappy]

Roger Ronas, change made, no sweat.

TH

[Triggerhappy]

johnfl, No idea, depends on a lot of things but mostly Miha's schedule. He'll fit it in when he can. I wouldn't expect it to take too long considering the speed at which people have been signing up. The last time I ran this buy we had about 120 molds on the order. He waited to build them until two other similar buys were ready then he built all three at the same time. This is a side business of his so it has a lot to do with his schedule and when he can fit it in.

Please be patient, we'll get it done as soon as we can.

TH

[Triggerhappy]

Thinktwice71, name fixed.

TH

[Chapped Lips]

Chapped Lips, great reason to get this mold! You're on the list.

Cheers,

TH

TH.......sorry to modify my order but got a Ruger 45 convertible flattop on order so........

please CHANGE the .452 to a solid........and

ADD a .454 hollowpoint (no penta).

Thanx and my apologies for the change.

[Triggerhappy]

Chapped Lips, you're all set.

TH

[JoeBob]

Hollowpoint with all pins 0.454"

Thanks,
JB

[Triggerhappy]

JoeBob, you're good to go.
Welcome!

TH

[Harry Callahan]

Hollowpoint with all pins .452"

skeepes at comcast dot net

Thanks

[Triggerhappy]

Harry, you're all set and good to go. Welcome!

TH

[Ozarklongshot]

Ok with much thought and justification I'm gonna bail in here and say
yes!!
Hollow point
.452 all pins
Stoneaxe42 (At) Yahoo (doot) Com

I may be new but thats the sweetest thing I've seen in a few moons

[Triggerhappy]

Orzarklongshot, you're good to go! Welcome!

TH